U-Reach PRO218 User manual

PRO218 (1-2)
HDD Duplicator
User Guide
EN
V 5.1
EN

2
Index
Disclaimer of Warranties……………………………………………………………………………. 3
Notice & Reminder…………………………………………………………………………………….. 3
Safety Precautions……………………………………………………………………………………… 3
Preparation Tips before You Start………………………………………………………………. 4
Product Features………………………. ……………………………………………………………… 4
Product Overview………………………………………………………………………………………. 5
Function Table…………………………………………………………………………………………… 6
Function Introduction………………………………………………………………………………… 9
1. Copy……………………………………………………………………………………..………….. 9
2. Compare……………………………………………………………………………………….....11
3. Copy+Compare………………………………………………………………………………… 11
4. Erase……………………………………………………………………………………………….. 12
4.1 Quick Erase………………………………………………………………………………….. 13
4.2 Full Erase…………………………………………………………………………………….. 13
4.3 DoD Erase……………………………………………………………………………………. 13
4.4 DoD EraseComp…………………………………………………………………………… 14
4.5 Secure Erase………………………………………………………………………………… 14
5. Utility…………………………………………………………………………..………………....14
5.1 Show Disk Info. …………………………………………………………………………… 14
5.2 Update System …………………………………………………………………………… 14
5.3 System Info. …………..………………………………………………………….………. 16
6. Setup………………………..………………………………………………………….…………. 16
6.1 Copy Area………………………………………………………………………………..... 16
6.2 Skip Error………………………………………………………………………………...... 19
6.3 Language………………………………………………………………………………...... 19
6.4 Advanced Setup……………………………………………………………………...... 19
6.5 Restore Default………………………………………………………………………….. 22
Specification Table…………………………………………………………………………………. 23

3
Disclaimer of Warranties
HDD series duplicators are made specifically for data backup with legal
authorities from copyright owners. Any unauthorized action of copyright is
strictly prohibited, and the manufacturer disclaims all warranties or
representations of illegal actions by users.
The manufacturer also disclaims any liability for any loss or damage due to not
being able to perform its undertakings or provide any of the services
attributable to any events or circumstances beyond our control. Users agree and
accept all statements above as soon as purchasing our products. This manual
contains materials that should be intended for personal use, all right reserved.
No part of this manual may be reproduced, transmitted or transcribed without
the expressed written permission of the manufacturer. The information present
in this manual is subject to change without prior notice.
Notice & Reminder
Read the complete operation instructions carefully, contributes to a better
operation.
Make sure the source device is correct and workable.
To guarantee data consistency, we highly recommend the capacity of source
and targets should be the same.
It is strongly suggested to use "Copy+Compare" to achieve a perfect
duplication.
Safety Precautions
The warranty will expire if damage is incurred resulting from non-compliance
with these operating instructions.
Store the equipment safely when not in use and keep out of the reach of
children/infants.
Please turn off the power before replacing the socket.
Never turn off the power while processing the firmware update.
Use only approved power sources.
The product is only suitable for operation in dry, dust free, clean
environment. Do not allow liquids or foreign objects to enter. Failure to do so
may severely damage your duplicator.

4
Preparation Tips before You Start
Make sure to use stable power supply.
Please use in a clean & dry environment.
Please keep the environment well ventilated.
When the duplicator operates, it is normal for the machine to heat up.
Please do not move the duplicator during operation to ensure better
operation.
Please do not remove HDDs during operation to avoid damage.
Please use power supply of its original manufacturer to ensure working
safety.
Static electricity may cause duplication error. Please pay attention to the
duplicator environment and operators’ equipment. It is recommended to
purchase static electricity elimination equipment to avoid static electricity
shock when in high static electricity environment.
Product Features
Ultra-High Speed
Support Various Interface
High copy speed for duplication and
data comparison.
Support 2.5" and 3.5" SATA HDD, IDE
HDD and SSD.
4 Kinds of Copy Areas
4 Erase Methods
Systems and Files, All Partitions,
Whole HDD, and Percentage Copy.
Quick Erase, Full Erase, DoD Erase
and Secure Erase.
Quick Copy Mode
Bad Sector Check
Quick copy mode copies only Data
and System area can highly increase
the copy efficiency.
Auto detects and shows the bad
sector quantity.
Auto Power Control System
Portable Design
Protect the HDD from damage during
hot removal from the duplicator.
Light weight for easy carry.

5
Product Overview
A. Hardware Overview
B. LCD Configuration
Red: Fail
Green: Pass
Yellow: Powering
Source Port
Target Port 2
UP: Backward
DOWN: Forward
OK: Confirm
ESC: Cancel
Copy x2 2047M
0:11 41% 860M
Target HDD
Total Size
(Source)
Copy progress %
Copied capacity
(Target)
Function
Copied time
Target Port 1

6
Function Table
Function
Description
1. Copy
Copy data from source HDD to targets. (There are four
copy modes for selection at function 6.1)
2. Compare
To compare data bit for bit between source and target
HDDs.
3. Copy+Compare
It makes copy first and then compare target HDD with
source HDD to ensure data correctness.
4. Erase
4.1 Quick Erase
To erase HDD’s index table only.
4.2 Full Erase
To erase whole HDD.
4.3 DoD Erase
To erase HDDs three times complying with USA
Department of Defense (DoD) standard.
4.4 DoD EraseComp
To erase HDDs three times complying with USA
Department of Defense (DoD) standard and bit by bit to
check if data is completely erased.
4.5 Secure Erase
The international authorized high standard Secure Erase
function.
5. Utility
5.1 Show Disk Info.
Shows HDD’s basic information such as HDD model name
and capacity.
5.2
Update
System
5.2.1 Update BIOS
To update the system firmware via a USB
pen drive or a HDD.
5.2.2 Create Update HDD
To format the HDD with a 2GB FAT
partition in order to quickly save
firmware in the HDD.
5.3 System Info.
Show information of the duplicator system, including
controller model number and software version.

7
6. Setup
6.1
Copy Area
Setup copy
mode.
System and Files
Set to copy source HDD's data only.
ALL Partitions
Set to copy source HDD's all partitions.
Whole HDD
Set to copy the whole source HDD.
Percentage (%)
Set up percentage range of HDD for copy.
6.2 Skip Error
Set to skip error of source HDD while Copy / Compare /
Erase.
6.3 Language
Select preferred language.
6.4
Advanced
Setup
6.4.1
Unknown
Format
Copy Unknown
Copy unknown format area.
Skip Unknown
Skip to copy unknown area.
6.4.2
Erase
Master
Disable
Disable erase source HDD.
Enable
Enable erase source HDD.
6.4.3
Erase
Pattern
ONE Byte
A random character to be
written into every byte.
Big Random Data
A set of random character to
be written into a set of area.
6.4.4 Wait HDD Time
Auto start time after plugging HDD from 0
~ 30 seconds.
6.4.5
Copy HPA
Area
Set to copy
HPA or not
No, Keep HPA
No, Clear HPA
No, Setting HPA
Copy and Setting

8
6.4.6
Clear HPA
at Erase
Clear HPA Setting
Keep HPA Setting
6.4.7 Transfer Rate
Select the proper transfer rate UDMA2-7.
6.4.8 Stop Motor Time
Auto running time after stopping motor.
6.5 Restore Default
Back to original manufacturer setting.

9
Function Introduction
1. Copy
It copies data from source HDD to target HDD. You can set following settings
before copy. (You can check more detail in ”6. Setup”.)
I. Set Copy Area of Source HDD →6.1 Copy Area
II. Set Copy Unknown Format Area →6.4.1 Unknown Format
Start to copy
Step 1: Prepare Source & Targets
Prepare a source HDD and target HDDs.
(It’s strongly recommended the source and target are the same capacity.)
Caution
Various adapters are required to copy device with different
interfaces, e.g. IDE, eSATA, mSATA, and etc.
Step 2: Place Source & Targets
Place source HDD at source port, target HDDs to Target port.
Step 3: Enter Function "1.Copy"
Use ▲▼ to select "1.Copy", and then press "OK". Duplication will start to
proceed.
Note
If the user set “6.4.4 Wait HDD Time” at 3-30 seconds, the
machine will start duplicating automatically after HDDs initialize.
If the user set “wait key to start,” need to press “OK" to start.

10
The information below shows on LCD during duplication.
Copy Process
(if there is any bad sector)
Step 4: Completion!
The copy result (Pass/Fail), total copy time and bad sectors will show on
monitor.
Copy result
Pass
Fail
Note
The default setting of error counter is 0. If users want to adjust
the accepted error sectors of the HDD, you can set "6.2 skip
error".
Copy 224M
0:02 85% 190M
Function
Total Data
Copied Data
Copied Time
Copy Process
Bad Sector R:0
0:01 48% W:1
Source bad sector
Target bad sector
Copied Time
Copy Process
Pass 0:05
No Bad Sector!
Fail 0:05
Bad Sector R0 W1
Total copy time

11
2. Compare
It is used to check if the data on source HDD is identical to target HDD after
duplication.
Start to compare
Step 1: Prepare Source and Targets
Prepare the source HDD and target HDDs to compare after duplication is
completed.
Step 2: Place Source and Targets
Place the source HDD to Source port, target HDDs to Target port.
Step 3: Enter "2.Compare"
Use ▲▼ to select “2.Compare” then press “OK”. Data compare will proceed.
Step 4: Completion!
The result (Pass/Fail) and time will show on LCD after comparison completes.
3. Copy+Compare
It makes copy first and then compare copied HDD with source HDD to confirm
the accuracy.
Note
It is recommended to execute Compare after Copy to confirm
the accuracy. Can use the function “3. Copy+Compare”.

12
4. Erase
Please choose the appropriate erase method when you like to dispose or re-
use the HDDs. You can set following settings before erase:
(You can check more detail in ”6. Setup”.)
I. Set Erase mode →6.1 Copy Area
II. Set Erase Master → 6.4.2 Unknown Format
III. Set Erase Pattern → 6.4.3 Erase Pattern
Caution
It will erase the data in the HDD, please make sure you backup
all important data before using this function.
Start to erase
Step 1: Prepare HDDs
Prepare HDDs for disposal.
Step 2: Place HDDs
Insert HDDs for disposal into target ports.
Note
Function "6.4.2 Erase Master" is to determine erase source HDD
or not.
Step 3: Enter function "4. Erase"
Use ▲▼ to select the mode of erasing method, and then press "OK". Data
Erase will proceed.
Note
During erasing, press ▲▼ to view the status of each port. Press
“OK”to see the details for each port.
There are several erase methods:
➊Quick Erase ➋Full Erase ➌DoD Erase ➍Secure Erase
HDD Duplicator
4. Erase

13
4.1 Quick Erase
The function will ONLY erase the index of the HDD. It is the quickest way to
erase HDD.
4.2 Full Erase
The function will erase the whole sectors on the target HDD. It will take a
longer time than quick erase.
4.3 DoD Erase (DoD5220.22 M)
This is to comply with the U.S.A. Department of Defense (DoD5220) standard
to fully erase the HDD three times bit-for-bit to overwrite HDD data and
guarantees data not recoverable. This DoD erase method will erase HDD over
each sector three times: the first time with zeros (0x00), second time with FF
(0xFF) and the third time with random characters.
4.4 DoD EraseComp (DoD5220.22 M)
Besides DoD erase 3 times, this function will also execute comparison to make
sure the random bit is correctly written.
DoD EraseComp Method:
000000000
000000000
000000000
000000000
000000000
000000000
000000000
000000000
00
FFFFFFFFFF
FFFFFFFFFF
FFFFFFFFFF
FFFFFFFFFF
FFFFFFFFFF
FFFFFFFFFF
FFFFFFFFFF
FFFFFFFFFF
FFFFF
#########
#########
#########
#########
#########
#########
#########
#########
####
#########
#########
#########
#########
#########
#########
#########
#########
#####
Step1. 0 x 00
Step2. 0 x FF
Step3. Random
Step4. Compare
[02] 74.5G
Erase (3) [4M] 5.2G
Port No.
Total capacity
Erased capacity
Erase No.
*The third times of erase.
Erase pattern

14
Note
1. The erasing duration of DoD Erase mode is 3 times longer
than full erase mode.
2. The duration of DoD EraseComp is 4 times longer than full
erase mode.
4.5 Secure Erase (NIST800-88)
The international authorized high standard Secure Erase function. It overwrites
every single track on the hard drive with "00". Even HPA/DCO or other data
area which are not able to load, can be erased all together.
Note
If you want to cancel executing work of Copy/Compare/Erase,
you can press “ESC” for few seconds to stop the task.
5. Utility
5.1 Show Disk Info.
This function will show HDD's basic information such as HDD capacity and
model number. Use ▲▼ to check the other port.
Shows HDD information
5.2 Update System
Step 1: Create an Update HDD
Place a SDD/HDD to the duplicator. Select function "5.2 Create Update HDD".
[01] 456GB
ST3500418AS
HDD capacity
Port No.
HDD model number
[Update System]
2. Create Update HDD

15
Step 2: Format BIOS HDD
Click "OK" to format the BIOS hard disk. One FAT, 2GB partition will be
formatted in HDD. That would reduce searching time, and speed up firmware
update.
Caution
The data saved in this HDD will be erased.
Step 3: Download Firmware
Connect the BIOS HDD to PC. Download the latest firmware from PC and save
it to HDD. Unzip BIOS, and save it to the root directory.
Step 4: Enter "Update BIOS"
Place the BIOS HDD into source port. Enter function "5.2.1 Update BIOS".
Update will take about a minute to complete.
Caution
Please do not disrupt during BIOS update, otherwise it would
cause irretrievable error on duplicator. We are not held
responsible for any damages.
Do FORMAT HDD#1
Confirm ?
[Update System]
1. Update BIOS

16
5.3 System Info.
This function shows information of the duplicator includes model name and
firmware version.
6. Setup
6.1 Copy Area
Users can set copy area of source HDD. Appropriate copy area can greatly
reduce operation time and have better efficiency. There are four copy modes
with different copy areas:
➊System and Files ➋ALL Partitions ➌Whole HDD ➍Percentage (%)
4 Copy Area
System and Files
Whole HDD
ALL Partitions
Percentage (%)
HDD Dupe 1-1
Ver: 2.35.9
System and Files
Whole HDD
ALL Partitions
Percentage (%)
Target
Source
%

17
6.1.1 System and Files (Quick Copy data area only)
It will copy source HDD’s System and Files instead of the whole HDD. The
system will analyze the source HDD and identify the data area to copy. As long
as the source HDD’s data is within the target HDD’s space, the copy will be
processed. FAT16/32/64, NTFS, ext2/3/4, HFS+, HFS, HFX are supported for this
copy mode.
6.1.2 ALL Partitions
Copy all of the partitions area bit-by-bit no matter if there is data that exists or
not. The capacity of target HDDs have to be bigger than the partition required
capacity.
Only 120G data area will be copied, it takes 12 minutes.
Source
Duplication
Target
500G
500G
150G
Undefined
Partition1 (150G)
Data 30G
Partition2 (200G)
Data 90G
[Copy Area]
ALL Partitions
Only 350G partition area will be copied, it takes 48 minutes.
Source
Duplication
Target
500G
500G
150G
Undefined
Partition1 (150G)
Data 30G
Partition2 (200G)
Data 90G
Partition 1
Partition 2

18
6.1.3 Whole HDD
Copies the whole source HDD, no matter of the content, format, partition or
empty space. This mode does not analyze the data.
6.1.4 Percentage (%)
Copy the selected percentage range of source HDD.
Partition1 (150G)
Data 30G
Partition2 (200G)
Data 90G
[Copy Area]
Whole HDD
[Copy Area]
Percentage
Only copies the selected area, other area or data will not be copied.
Source
Duplication
Target
500G
17%
32%
150G
Undefined
17%
32%
Entire 500GB HDD will be copied.
Source
Duplication
Target
500G
500G
150G
Undefined

19
How to select the proper copy area?
Example: There are two partitions in one 500G HDD.
6.2 Skip Error
This function sets the number of error you like to skip during copy / compare /
erase process. The default is 0. You can choose 0-65535 or unlimited.
6.3 Language
Select preferred language. You can select English or Japanese.
6.4 Advanced Setup
6.4.1 Unknown Format
This function allows you to select if you want to copy the unknown format
area. This function will only affect Quick Copy.
100G
250G
60G Data
30G Data
System and files
All Partitions
500G
500G
250G
Whole HDD
Copy / Compare area
30G+60G= 90G
Copy / Compare area
500G
Copy / Compare area
100G+250G= 350G
150G
Undefined
150G
Undefined
150G
Undefined
500G
100G
250G
100G
[Skip Error]
0

20
6.4.1.1 Copy Unknown
Copy all the unknown area if device cannot identify the format during copy.
6.4.1.2 Skip Unknown
Skip the unknown area if device cannot identify the format during copy.
6.4.2 Erase Master
It is set to allow erase source HDD or not. Please make sure of this setting
before you execute DoD erase. The default setting is ”Disable”.
6.4.3 Erase Pattern
Enable to select overwrite data pattern mode during erase.
ONE Byte
[00] or a fixed character will be written into every byte.
Big Random Data
A random character to be written into every byte.
It will show [4M] while erase.
[Unknown Format]
Copy Unknown
[Erase Master]
Disable
[02] 74.5G
Erase [00] 5432M
[02] 74.5G
Erase [4M] 5432M
353535353535
353535353535
353535353535
353535353535
353535353535
353535353535
JXDOD142XJM
IKDS14CWQ2X
LSA2E5VKOZE1
4OFEW2ZB259
E4X2DGR43ZQ
58RR8V3QWP
92X1