U-Reach UB800 User manual

UB800/SD800
1-7
Flash Duplicator
User Manual v A.01

Index
Product Disclaimer ................................................................................................. 3
Warranty ..................................................................................................................... 3
Piracy Statement...................................................................................................... 3
Before You Start ....................................................................................................... 4
Notice Symbols......................................................................................................... 4
Introduction............................................................................................................... 5
Function Table .......................................................................................................... 7
1.Copy........................................................................................................................ 11
2.Compare ............................................................................................................... 11
3.Copy&Compare.................................................................................................. 12
4.Fmt+Copy+Compare...................................................................................... 12
5. Information ........................................................................................................ 13
6. Utility .................................................................................................................... 14
7. Setup ..................................................................................................................... 16
FAQ ............................................................................................................................. 20
Specification ........................................................................................................... 23
V A.01.1

3
Product Disclaimer
U-Reach is not accountable for any incidental or consequential damages, which
includes, but is not constrained to property harm, loss of time or data from use
of a U-Reach product, or any other damages attributable to product malfunction
or failure (including without limitation, those attributable to: (1) reliance of the
materials provided, (2) costs of product replacement, (3) loss of use, data or
profits, (4) delays or business interruptions, (5) and any principle of legal
responsibility, arising out of or in reference to the use or overall performance or
from delays in servicing or lack of ability to render service) of any U-Reach
product. U-Reach makes every effort to ensure proper operation of all products.
However, the customer is responsible to affirm that out of the U-Reach product
meets the customer’s quality requirement. The customer further acknowledges
that fallacious operation of U-Reach product and/or software program, or
hardware issues, can cause loss of data, defective formatting, or data loading.
U-Reach will make efforts to resolve or repair any issues recognized by
customer either within the warranty period or on a time and materials basis.
Specifications and features subject to change without notice or obligation.
Warranty
U-Reach provides a basic one-year parts and labor warranty for all of its
products (excluding cables, adapters, and other consumable items). An optional
extended warranty is also available for an added cost. Telephone and email
support is available for the life of the product as defined by U-Reach.
All warranties will be restricted and defined by the market region from which
customers purchased.
Piracy Statement
U-Reach accepts no responsibility for copyright infringement or misuse of any
U-Reach equipment. Copying all forms of data: audio, video, or software
without the permission of the copyright holder is illegal. It is the sole
responsibility of the user to ensure that the legal copyrights of the copyright
owners are respected.

4
Before You Start
Important Notice
⚫Carefully read the entire manual before operating.
⚫Make sure the source device is correct and functioning.
⚫Equal capacity of source and target is recommended for guaranteed data
consistency.
⚫Using the Copy+Compare function provides the most flawless duplication.
⚫Damage incurred due to non-compliance with U-Reach operating
instructions will void the warranty.
⚫Store the equipment safely when not in use and keep out of the reach of
children.
⚫Please turn off duplicator before replacing a socket.
⚫Never turn off the power while the firmware is updating.
⚫Use only approved, stable power sources.
⚫Use product only in a clean, dry, dust-free, and ventilated area. Liquids or
foreign debris can severely damage your duplicator.
⚫It is typical for the machine to heat up during operation.
⚫While in use, do not move the duplicator or remove devices.
⚫Static electricity may cause duplication error. Please pay attention to the
duplicator’s environment while operating equipment. Purchasing electricity
elimination equipment helps avoid shock.
Notice Symbols
Special items, procedures, or notes to be observed prior to use.
Note
Refers to related duplicator operations, special details, tips, or
suggestions for operational effectiveness.
Caution
Refers to procedures that need to be adhered to or precautions.

5
Introduction
1. Features
Apart from inheriting the high-speed performance and well-recognized
compatibility with diversified media, the flash duplicators support easy and fast
duplication. Through a user-friendly interface, the flash duplicators can be
operated standalone with no steep learning curve for users to climb. Their
ergonomic design facilitates efficient operations by letting users easily insert
and remove flash cards, and the 20%~80%-reduced footprint compared with
their peers in the market has led to better space utilization and freight savings.
⚫Ultra-high transmission speed, each flash slot channel is independent from
each other.
⚫Real multi-task processing capability. Whether it is copy, compare or format,
each feature is independently executed. Each flash slot has an independent
control processing unit.
⚫Non-PC based, with no risk of virus infection. Instant power on and off.
⚫One-touch copy. Real time information will be shown on the LCD screen.
⚫Supports Synchronous and Asynchronous copy/ compare/ erase/ format.
⚫Ultra high-speed bit-for-bit hardware comparison.
⚫Different SD card speed selection is available for different quality level flash
media.
2. Package Contents
Duplicator x 1
12V DC
Adaptor x 1
Power Cord x 1
User Manual x 1

6
3. Hardware Overview
⚫Front View (UB800)
⚫Front View (SD800)
⚫Back View
LCD Display
Control Buttons
Source Port
LED Indicators
Green: Pass
Red: Fail
Power Switch
Power Supply
Source Port

7
Function Table
⚫UB800
Function
Description
1. Copy
Data only or whole media duplication.
2. Compare
Bit-by-bit comparison between the source and all
other copied flash medias.
3. Copy&Compare
First copies then compares the copied flash media
with the source immediately after the copy has
finished.
4. Information
4.1 USB Info.
This feature will show flash’s information of data; file
format, content size, and capacity.
5.2 System Info.
This feature will show information of the duplicator
system, including machine model number and
software version.
5. Utility
5.1 Do Format
5.1.1 Auto Format
Auto format media to be FAT16 or 32.
5.1.2 FAT16 Format
Format media to be FAT16.
5.1.3 FAT32 Format
Format media to be FAT32.
5.1.4 Set FAT 16 Cluster Size
Set the size of FAT16 Cluster.
5.1.5 Set FAT 32 Cluster Size
Set the size of FAT 32 Cluster.
5.2 Quick Erase
Erases the content of flash media. It will keep the FAT
format.

8
5.3 Full Erase
Erases completely bit for bit of data on flash including
format and content, takes more time.
5.4 System Update
System firmware updating via the flash media.
6. Setup
6.1 Copy Area
System and Files
The system can automatically
analyze the format of source data
and only copy the data area.
(Available for FAT16/32/64, NTFS,
Linux (ext2/ext3/ext4) )
Whole Media
The system will copy the whole
content of flash including the empty
space.
6.2 Target Tolerance
Set the tolerance % of capacity gap between the
source and target. The default setting is “No limit”.
6.3 Power Off Time Between Copy&Compare
Set the power-off time between Copy and Compare
when executing “Copy&Compare” function.
6.4 Select Speed
Sets data transmission speed.
6.5 Monitor Device After Copy
Allows user to set a device status check after
duplication.
6.6 Set to Default
Back to original manufacturer setting.

9
⚫SD800
Function
Description
1. Copy
Data only or whole media duplication.
2. Compare
Bit-by-bit comparison between the source and all
other copied flash medias.
3. Copy&Compare
First copies then compares the copied flash media
with the source immediately after the copy has
finished.
4. Fmt+Copy+Comp
Formats SD cards, copies, and then compares the
copied flash media with the source immediately after
the copy has finished.
5. Information
5.1 SD Card Info.
This feature will show flash’s information of data; file
format, content size, and capacity.
5.2 System Info.
This feature will show information of the duplicator
system, including machine model number and
software version.
6. Utility
6.1 Do Format
6.1.1 Auto Format
Auto format media to be FAT16 or 32.
6.1.2 FAT16 Format
Format media to be FAT16.
6.1.3 FAT32 Format
Format media to be FAT32.
6.1.4 Set FAT 16 Cluster Size
Set the size of FAT16 Cluster.
6.1.5 Set FAT 32 Cluster Size
Set the size of FAT 32 Cluster.
6.2 Quick Erase
Erases the content of flash media. It will keep the FAT
format.

10
6.3 Full Erase
Erases completely bit for bit of data on flash including
format and content, takes more time.
6.4 System Update
System firmware updating via the flash media.
7. Setup
7.1 Copy Area
System and Files
The system can automatically
analyze the format of source data
and only copy the data area.
(Available for FAT16/32/64, NTFS,
Linux (ext2/ext3/ext4) )
Whole Media
The system will copy the whole
content of flash including the empty
space.
7.2 Target Tolerance
Set the tolerance % of capacity gap between the
source and target. The default setting is “No limit”.
7.3 Power Off Time Between Copy&Compare
Set the power-off time between Copy and Compare
when executing “Copy&Compare” function.
7.4 Select Speed
Sets data transmission speed.
7.5 Set to Default
Back to original manufacturer setting.

11
1.Copy
Copy area setting ➡[Setup >> Copy Area]
Before duplication, select the area of data with "Copy area".
Select "System and Files"
Select "Whole Media"
2.Compare
Compare function checks the correctness of
copying result. After the copying process is
finished, go to function 2 and press "OK" to start
comparing process.
Note
⚫If user pulls out the flash card during copy process, the
system will stop immediately and red light will turn on to
notify users copy has failed. It is strongly suggested that
users avoid this action because it will damage the flash card.
⚫Original data in the target flash cards will be lost after the
copy process is completed. Backup the existing data before
starting the copying process.
1.Copy(Data)
1.Copy(Whole)
1.Copy(Data)
Copy 7695M
3% 0:27 (3)270M
(3) means the Port
No.3 is the slowest
port.
2.Compare

12
3.Copy&Compare
This function is the most convenient. Instead of going to function [2.Compare]
and pressing "OK" again after copying, function [3.Copy&Compare] will
automatically run the compare function after copying process is finished to
make sure the copied result is correct.
Caution
The user is responsible for verifying the targets’ quality. Please
pick a few completed targets and test in a mass production
environment for quality control.
4.Fmt+Copy+Compare (Available in SD800)
This function will automatically run the format function before copy, and run the
compare function after copying process is finished to make sure the copied
result is correct.
Note
⚫Press ▲▼ together for 5 seconds to stop the slowest port
during operation.
⚫Press “ESC” for 5 seconds to stop all the ports during
operation.
⚫It is recommended to reboot the machine after manually
stopping the copy.
3.Copy&Compare

13
5. Information
5.1 USB / SD Card Info.
This function will show the flash media’s basic information such as file format,
content size, and total capacity.
Press ▲▼ buttons to check the information of each flash media including the
source.
5.2 System Info.
This function will show the information of the duplicator’s system, including
model number and software version.
Note
Executing this function will not delete the content or format of
flash media.
SD 1-7
Ver: 2.40.8
Press
▼
for further information.
[#01] 3871M
FAT32 230M
Total Capacity of the Device
Data Size

14
6. Utility
6.1 Do Format
6.1.1 Auto Format
This function is to format flash into FAT. Plug the flash media in the slot and
press "OK", the system will automatically detect its capacity first and then
format the media according to its capacity.
⚫If the flash media format is already FAT16 or FAT32, the format function
won’t change its original format.
⚫If the original flash media is not in FAT format, i.e. NTFS, Linux or FAT multi-
partition. The system will execute format according to flash’s capacity. When
its capacity is above 2GB, the system will format the flash media to FAT32. If
its capacity is below 2GB, the system will format the flash media to FAT16.
Caution
⚫The source port (port#1) will not execute any formatting
because this function will delete the data of the flash media.
⚫The user is responsible for verifying the targets’ quality. Please
pick a few completed targets and test in a mass production
environment for quality control.
6.1.2 FAT16 Format
Press "OK" to format any flash media to FAT16 format.
Capacity < 2GB
Format FAT16
Capacity > 2GB
Format FAT32

15
6.1.3 FAT32 Format
Press "OK" to format any flash media to FAT32 format.
6.1.4 Set FAT16 Cluster Size
Set the size of FAT16 cluster.
6.1.5 Set FAT32 Cluster Size
Set the size of FAT32 cluster.
6.2 Quick Erase
This function erases flash data while keeping the format if the original flash
format is FAT16/32. Use the ▲▼buttons to view status, progress, and
information.
6.3 Full Erase
Completely erases the entire flash media, including format and content. This
task takes longer. Pressing <ESC> during this process will abandon the task, but
the original format and content will no longer be readable.
Note
Quick erase function will erase only FAT 16/32 formatted flashes.
[Utility]
1. Quick Erase
Do ERASE ALL
Confirm?
[Utility]
2. Full Erase
Do ERASE ALL
Confirm?

16
6.4 System Update
Step 1: Prepare a USB/SD Card for update.
Connect a USB/SD card to PC. Download the latest firmware, unzip the BIOS
firmware, then save it to the root directory in the USB/SD card.
Step 2: Proceed to update firmware.
Connect the USB/SD card to the source port. Scroll to select "6.4 Update BIOS”,
then press "OK" to start the firmware update process.
Caution
The firmware update process may take longer than 5 minutes.
Please do not disrupt power or process during BIOS update. If
interrupted, the system will become useless. U-Reach will not be
held responsible for any damages.
7. Setup
7.1 Copy Area
❶ System and Files
It is also called "Quick Copy" mode. The system will automatically analyze the
source flash card's file format. If the data's file format is FAT16/32/64, NTFS,
Linux (ext2/3/4) which is recognizable by the system, it will only copy data
instead of the whole flash.
Note
The USB’s format must be: FAT16 or FAT32.
[Copy Area]
System and Files
Copy 2GB data only

17
❷ Whole Media
The system will copy the whole flash card, including the empty space and
format. This function is used when users want to copy the whole flash or have a
flash source with unknown format. It will take a longer time to make "Whole
media" copy.
7.2 Target Tolerance
This function sets the acceptable difference range of flash capacities between
the source and target. If the capacity difference between the source and target
exceeds the tolerance setting, the copy will fail.
For example, if the target tolerance setting is "±1%", the targets whose
capacities are more than 2.02GB or less than 1.98GB won't be copied.
Note
If the file format is non-recognizable, the system will still copy
the whole flash card including the empty space even if you
select "System and Files" as your copy area.
[Copy Area]
Whole Media
Copy total 8GB
8GB
Source Target tolerance setting: ± 1%
Real Capacity 2GB 2.02GB (2GB +1%) 1.98GB (2GB -1%)

18
7.3 Power Off Time Between Copy&Compare
This setting is to prevent from any data loss because of unstable flash, we
strongly recommend you use this function to set the time gap of power supply
between copy and compare.
The time gap can be set from 0 to 15 seconds.
The default setting is "0".
7.4 Select Speed
There are 5 transmission speed options:
⚫Slowest Mode
⚫Slower Mode
⚫Normal Mode (Default)
⚫Faster Mode
⚫Fastest Mode
Use a good quality flash media that supports a faster mode. If unsure about the
flash quality or notice a high copy/compare failure rate, use a slower
transmission speed. The default setting is “Normal Mode”.
7.5 Monitor Device After Copy (Available in UB800)
Allows user to set a device status check after duplication. The settings could
show different results because each device has various settings.
For example, if a device is set to power off automatically after “complete”
command, then user must set “Do NOT Check” to make sure the LCD keeps the
[Power Off Time Between Copy&Compare]
3
[Select Speed]
Normal Mode

19
copy result for reference.
In this case, if set at “Do Check”, the copied device will power off automatically
after Copy job completes and the LCD will back to the previous job.
7.6 Set to Dfault
Restores original default settings.
Complete
All Parameter was cleared!
[Set to Default]
[Monitor Device After Copy]
Do Check
Total OK: 10 NG: 0
12:48 OK: 10 NG: 10
[Monitor Device After Copy]
Do NOT Check
1. Copy (Data)

20
FAQ
Q1.How to Prevent from Failed Duplication?
A:
➢Stable Devices
❶Good Connector
The adapter, extension cord, and card reader
must be in good quality for proper connection.
❷Stable Flash
Use the flash devices with stable quality.
❸Good Source
Make sure your source is a good source.
➢Suitable Data & Settings
❶Target Tolerance Settings. [Setup >> Target Tolerance]
Go to Function "Target Tolerance" to check if the
setting of capacity difference range between source
and target is right.
❷Capacity of the Data in Source
Make sure that the data of source is within the
capacity of target.
❸Capacity of Targets
When copying formats NTFS/Linux copy, make sure
that the target's capacity is equal to or larger than your
source.
[Target Tolerance]
No Limit