Ubiquiti GBE-LR User manual

Dish Main Arm Stabilizer Arms (Qty. 2)
Mounting Bracket Screw U-Clamp
Package Contents
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Flat Washers (Qty. 2) Lock Washers (Qty. 2) Flange Nuts (Qty. 2)
Gigabit PoE (24V, 0.5A) with
Mounting Bracket
Power Cord
Installation Requirements
Clear line of sight between GigaBeam AP and station
Vertical mounting orientation
Mounting point:
At least 1 m below the highest point on the structure
For tower installations, at least 3 m below the top of the tower
Outdoor, shielded Category 6 (or above) cabling and shielded RJ45 connectors are
required for all wired Ethernet connections.
Surge protection should be used for all outdoor installations. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the device and
the other at the entry point to the building. The ETH-SP-G2 will absorb power surges
and safely discharge them into the ground.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Note: For guidelines about grounding and lightning protection, follow your
local electrical regulatory codes.
Hardware Overview
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

60 GHz LED
5 GHz LED
LAN LED
Lights steady blue when the 60 GHz link is ready.
Lights steady blue when the 5 GHz link is ready.
The LED will light steady blue when an active Ethernet connection is made to the
Ethernet port and flash when there is activity.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Power/Status LED
PoE IN Port
Reset Button
Flashing White Bootup in progress.
White
Ready for use, not connected to Ubiquiti® Network
Management System (UNMS™). See “UNMS
Management”.
Blue Ready for use, connected to UNMS.
Steady Blue with
Occasional Flashing
Ready for use, unable to connect to UNMS, check
connection to UNMS server.
Quickly Flashing Blue Used to locate a device in UNMS.
Alternating
Blue/White Firmware upgrade in progress.
This Gigabit Ethernet port is used to connect the power and should be connected to
the LAN and DHCP server. Default IP address: 192.168.1.20.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on. Alternatively, the device may be reset
remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.
Installation
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

1.
2.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3.
OPTIONAL
Attach the stabilizer arms for added support.
(This is recommended for long-range installations.)
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

4.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Note: The GBE-LR can mount on either side of the pole. This section shows
the GBE-LR mounted on the left; the procedure for mounting on the right is
similar.
OR
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Left Right
5.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Note: Rotate the Mounting Bracket clockwise until it locks into position.
6.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

7.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

8.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

(Pole not shown)
9.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

10.
11.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

12.
13.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Connecting Power
WARNING: The switch port must comply with the power specifications listed in
“Specifications”.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

OR
Optional
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD