Ubiquiti EdgeRouter ER-12P User manual

EdgeRouter ER-12P Wall Mount Screws (Qty. 2) Wall Mount Anchors (Qty. 2)
Ground Screw Power Adapter (24V, 2.5A) Power Cord
Package Contents
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Cable Clip
Installation Requirements
Wall mounting (optional)
Drill with 6 mm drill bit
Phillips screwdriver
For indoor applications, use Category 5 (or above) UTP cabling approved for indoor
use.
For outdoor applications, shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from harmful outdoor environments
and destructive ESD events with industrial-grade, shielded Ethernet cable from
Ubiquiti. For more details, visit: ui.com/toughcable
Hardware Overview
Note: Although the cabling can be located outdoors, the EdgeRouter itself
should be housed inside a protective enclosure.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

System LED
Flashing White Bootup in progress.
White
Ready for use, not connected to Ubiquiti® Network
Management System (UNMS™). See “UNMS
Management”.
Blue Ready for use, connected to UNMS.
Steady Blue with
Occasional Flashing
Ready for use, unable to connect to UNMS, check
connection to UNMS server.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

RJ45 PoE LED (Ports 0 - 9)
RJ45 Speed/Link/Activity LED (Ports 0 - 9)
SFP Link/Activity LED (Ports 10 - 11)
Quickly Flashing Blue Used to locate a device in UNMS.
Alternating
Blue/White Firmware upgrade in progress.
Off No PoE
Green 24V Passive PoE Output
Off No Link
Amber Link Established at 10/100 Mbps
Amber Flashing Link Activity at 10/100 Mbps
Green Link Established at 1000 Mbps (1 Gbps)
Green Flashing Link Activity at 1000 Mbps (1 Gbps)
Off No Link
Green Link Established at 1 Gbps
Green Flashing Link Activity at 1 Gbps
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Console
USB
RJ45 (Ports 0 - 9)
SFP (Ports 10 - 11)
Reset Button
Power
Grounding Point
RJ45 serial console port for Command Line Interface (CLI) management.
Reserved for future use.
All RJ45 ports can be used for routing. They support 10/100/1000 Mbps Ethernet
connections and 24V Passive PoE output. Ports 0 - 7 can be configured for
switching functions using the EdgeOS® Configuration Interface.
SFP routing ports are hot-swappable and support Gigabit fiber SFP modules.
Click here to learn how to reset an EdgeRouter to factory defaults.
Connect the included Power Adapter to the Power port.
Ground bonding point for an optional ground wire.
Hardware Installation
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Wall Mounting
1.
2.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

4.
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Grounding the EdgeRouter (Recommended)
The Power Adapter grounds the device; however, you can add optional ESD grounding
for enhanced ESD protection (ground wire not included).
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Optional
Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD