Ubiquiti EdgeRouter X ER-X User manual

Advanced Gigabit
Ethernet Router
Model: ER-X

Introduction
Thank you for purchasing the Ubiquiti Networks®
EdgeRouter™X. This Quick Start Guide is designed to guide
you through installation and also includes warranty terms.
Package Contents
Advanced Gigabit
Ethernet Router
Model: ER-X
EdgeRouter X Power Adapter
(12V, 0.5A)
Quick Start Guide
Installation Requirements
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections.
To enhance ESD protection, attach a ground wire (not
included) to the back panel of the EdgeRouter X.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial‑grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable
Note: Although the cabling can be located outdoors,
the EdgeRouter X itself should be housed inside a
protective enclosure.
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, indoor cabling requirements, and Dynamic Frequency Selection
(DFS) requirements.

Hardware Overview
Top Panel
Power Ethernet (eth0-eth4)
LED State Status
Power
Off Power Off
Green Power On
eth0‑eth4
Off No Link
Green Link Established at 10/100/1000Mbps
Flashing Indicates Activity
Front Panel
Ethernet (eth0/PoE In) Ethernet (eth1-eth3) Ethernet (eth4/PoE Out)
Port Description
eth0/PoE In
RJ45 port accepts 24V passive PoE
and supports a 10/100/1000 Ethernet
connection.
eth1‑3 RJ45 ports support 10/100/1000 Ethernet
connections.
eth4/PoE Out RJ45 port supports passive PoE passthrough
and a 10/100/1000 Ethernet connection.

Passive PoE Passthrough
The EdgeRouter X can be powered by either method:
• Power adapter
• 24V passive PoE on the eth0/PoE Inport
Passive PoE output on port eth4/PoE Out works as a
passthrough and depends on the input power source.
If the included Power Adapter (12V, 0.5A) is used, there may not
be sufficient passthrough to power another device because
the EdgeRouter X can consume up to 5 watts on its own.
We recommend using a more powerful input power source
(not included); here are a few examples of viable power input
options for passive PoE passthrough:
Power Input Passive PoE Passthrough
24V passive PoE (on eth0/PoE In)* ≈23V, 5W
12V, 1A
(ERLite-3 Power Adapter) ≈11V, 5W
24V, 2.5A
(ERPoe-5 Power Adapter) ≈23V, 11W
* Not compatible with 24V, 1A Gigabit PoE Adapter.

Back Panel
PowerGround
Reset
Button Description
Reset
There are two methods to reset the
EdgeRouter X to factory defaults:
Runtime Reset (Recommended)
The EdgeRouter X should be running after
bootup is complete. Press and hold the Reset
button for about 10 seconds until the eth4
LED starts flashing and then becomes solidly
lit. After a few seconds, the LED will turn off,
and the EdgeRouter X will automatically
reboot.
Power‑on Reset
1. Disconnect the Power Adapter from the
EdgeRouter X.
2. Press and hold the Reset button while
connecting the Power Adapter to the
EdgeRouter X. Keep holding the button
until the eth4 LED starts flashing and then
stops flashing after a few seconds.
Detail Description
Ground
ESD grounding for enhanced ESD protection.
The ground wire and screw with washer
are not included (recommended screw size:
M3-0.5 x 4 mm).
Power Connect the Power Adapter.

Hardware Installation
Place the EdgeRouter X on a flat, horizontal surface or mount it
on a wall (mounting screws not included).
Note: For adequate airflow, keep 20 mm of clearance
next to the ventilation holes of the EdgeRouter X.
Connecting Power
Follow the appropriate instructions for your installation:
Connecting Power Using the Power Adapter
Connect the Power Adapter to the Power port of the
EdgeRouter X. Then plug the Power Adapter into a
poweroutlet.
Connecting Power Using PoE
Connect the PoE cable of a PoE switch or adapter to the
eth0/PoE In port of the EdgeRouter X.

Accessing the Configuration Interface
1. Follow the appropriate instruction for your installation:
• If you are using the Power Adapter, then connect
an Ethernet cable from the Ethernet port of your
host system to the port labeled eth0/PoE In on the
EdgeRouter X.
• If you are using PoE, then connect your host system to
the PoE switch or adapter.
2. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet.
3. Launch your web browser. Type https://192.168.1.1 in the
address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username
and Password fields. Read the Ubiquiti License Agreement,
and check the box next to I agree to the terms of this License
Agreement to accept it. Click Login.
The EdgeOS Configuration Interface will appear, allowing
you to customize your settings as needed. You can click the
Wizards tab to access the Setup Wizard.
For more information, refer to the EdgeOS User Guide, which is
available at documentation.ubnt.com/edgemax

Specifications
EdgeRouter X
Dimensions 110 x 75 x 22 mm (4.33 x 2.95 x 0.87")
Weight 175g (6.17 oz)
Max. Power Consumption 5W
Power Input
12VDC, 0.5A Power Adapter (Included)
or
24V Passive PoE
Power Supply External AC/DC Adapter
Supported Voltage Range 9 to 26VDC
Button Reset
LED Power, Ethernet 0‑4
Processor Dual-Core 880 MHz, MIPS1004Kc
System Memory 256 MB DDR3 RAM
Code Storage 256 MB NAND
Certications CE, FCC, IC
Wall‑Mount Yes
Operating Temperature -10 to 45° C (14 to 113° F)
Operating Humidity 10 to 90% Noncondensing
Networking Interfaces
Data/PoE Input Port
Data Ports
Data/PoE Passthrough Port
(1) 10/100/1000 RJ45 Port
(3) 10/100/1000 RJ45 Ports
(1) 10/100/1000 RJ45 Port

Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.
*640-00142-05*
640-00142-05