Ubiquiti 3GStation Professional User manual

3G to WiFi and
Ethernet Bridge

1
Overview
Overview
Thank you for purchasing the 3GStation Professional.
Ubiquiti Networks offers three different models:
• 3GStation
• 3GStation Professional
• 3GStation Carrier
This Quick Start Guide is designed for use with the 3GStation
Professional. The 3GStation and 3GStation Carrier models have
their own separate documentation. The chart below provides an
overview of the differences between the three versions:
Feature 3GStation
3GStation
Professional
3GStation
Carrier
Application Indoor Indoor Indoor/Outdoor
3G USB Support   
PCI-E/SIM Support  
3G Booster Support  
3G Antenna 2dBi 5dBi
Wall-Mount Included  
Hi-Power WiFi 
2nd Ethernet PoE Out 
Package Contents
3G to WiFi and
Ethernet Bridge
3GStation
Professional (*)
Antennas 24V PoE Adapter Power Cord Quick Start Guide
Wall-Mount
Bracket
Desktop
Stand
M2.9x20 Self Tapping
Screws (Qty. 4)
M3x20 Anchors
(Qty. 4)
RPSMA to U.FL
Cable
(*) 1 RPSMA to TS9 cable and 1 RPSMA to U.FL Cable are already connected inside the
3GStation Professional.

2
3GStation Professional
Installation Requirements
• 3G USB Adapter or mini PCIe card (not included)
• 3G Internet service
Product Overview
Front Panel
Power LED The first LED is the Power LED which indicates the
power adapter is connected properly.
Ethernet LED The second LED indicates that the black Ethernet
connector on the power adapter is connected properly to a device.
3G Modem Received Signal Strength LEDs (3-6) Indicates signal
strength between the 3GStation Professional and 3G connection.
LED Threshold Value
3 min/-110 dBm
4 -95 dBm
5 -80 dBm
6 -65 dBm

3
Product Overview
Rear Panel
Ethernet Port
USB Port
Antenna Connectors
Antenna Connectors Connects the antennas.
USB Port Connects a 3G USB Adapter.
Ethernet Port Standard 10/100 Ethernet port that connects to
the power adapter using an Ethernet cable.

4
3GStation Professional
Hardware Installation
The 3GStation Professional includes a desktop stand and a
wall-mount assembly. You can use either a 3G USB Adapter or a
miniPCIe card with the 3GStation Professional.
Connecting a USB Adapter
1. Connect the TS9 connector to the 3G USB adapter.
MICRO SD
2. Connect the antennas the 3GStation Professional (as shown on
page 9 of this guide). Connect the 3G USB Adapter to the USB
Port on the 3GStation Professional.

5
Hardware Installation
Installing a miniPCIe Card
1. Remove the two M1.6 screws from the bottom of the 3GStation
Professional. Slide off the front cover of the 3GStation
Professional by pressing down on it while holding the sides of
the back cover.
Slide down
Remove Screws
Note: Be careful when sliding the door down not to
damage the on-board antennas.
2. Carefully lift the circuit board while holding it by the edges.

6
3GStation Professional
3. Unscrew and remove the RPSMA toTS9 cable.

7
Hardware Installation
4. Replace the RPSMA to TS9 cable with the RPSMA to U.FL cable.
5. Align the connectors on the miniPCIe card to the slot and slide
it into position. The card will snap into place.
WIRELESS
MAIN
AUX

8
3GStation Professional
6. Connect the U.FL connectors on the RPSMA cables to the U.FL
connectors on the mini PCIe card.
WIRELESS
MAIN
AUX
7. Insert your 3G Sim Card into the 3G Sim slot.
WIRELESS
MAIN
AUX
3G
5637347834939523434
8. Reconnect the front cover of the 3GStation Professional by
sliding up the front cover while holding the sides of the back
cover. Reconnect the two M1.6 screws.
Slide up
Note: Be careful when sliding the door up not to
damage the on-board antennas.