Ubiquiti ER-12 User manual

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 1/13
EdgeRouter ER-12 Wall Mount Screws (Qty. 2) Wall Mount Anchors (Qty. 2)
Ground Screw Power Adapter (24V, 1A) Cable Cl  p
Package Contents
Installat  on Requ  rements
Wall-mount  ng (opt  onal)
Dr  ll w  th 6 mm dr  ll b  t
Ph  ll  ps screwdr  ver
For  ndoor appl  cat  ons, use Category 5 (or above) UTP cabl  ng approved for  ndoor
use.
For outdoor appl  cat  ons, sh  elded Category 5 (or above) cabl  ng should be used for
all w  red Ethernet connect  ons and should be grounded through the AC ground of
the power supply.
We recommend that you protect your networks from harmful outdoor env  ronments
and destruct  ve ESD events w  th  ndustr  al-grade, sh  elded Ethernet cable from
Ub  qu  t  . For more deta  ls, v  s  t: u  .com/toughcable
Note: Although the cabl  ng can be located outdoors, the EdgeRouter  tself
should be housed  ns  de a protect  ve enclosure.
Hardware Overv  ew
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 2/13
System LED
RJ45 Speed /L  nk /Act LED (Ports 0 - 9)
PoE LED
SFP L  nk /Act LED (Ports 10 - 11)
Note: The System LED funct  onal  ty has been updated w  th f  rmware v1.10.7.
We recommend that you update the EdgeRouter to the latest f  rmware.
Flash  ng Wh  te Bootup  n progress.
Wh  te Ready for use, not connected to Ub
 qu  t  ® Network
Management System (UNMS™).
Blue Ready for use, connected to UNMS.
Steady Blue w  th
Occas  onal Flash  ng Ready for use, unable to connect to UNMS, check connect  on to UNMS server.
Qu  ckly Flash  ng Blue Used to locate a dev  ce  n UNMS.
Alternat  ng Blue/Wh  te F  rmware upgrade  n progress.
Off No L  nk
Amber L  nk Establ  shed at 10/100 Mbps
Amber Flash  ng L  nk Act  v  ty at 10/100 Mbps
Green L  nk Establ  shed at 1000 Mbps
Green Flash  ng L  nk Act  v  ty at 1000 Mbps
Off No PoE
Green 24V 2-Pa  r Pass  ve PoE Output
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 3/13
Console
RJ45 (Ports 0 - 9)
SFP (Ports 10 - 11)
Reset Button
Off No L  nk
Green L  nk Establ  shed at 1 Gbps
Green Flash  ng L  nk Act  v  ty at 1 Gbps
RJ45 ser  al console port for Command L  ne Interface (CLI) management.
All RJ45 ports can be used for rout  ng and support 10/100/1000 Mbps Ethernet
connect  ons. Ports 0 - 7 can be conf  gured for sw  tch  ng funct  ons us  ng the EdgeOS
Conf  gurat  on Interface. Port 0 supports 24V Pass  ve PoE In and port 9 supports
opt  onal Pass  ve PoE Out (d  sabled by default).
SFP rout  ng ports are hot-swappable and support G  gab  t f  ber SFP modules.
Cl  ck here to learn how to reset an EdgeRouter to factory defaults.
Wall Mount  ng
1.
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 4/13
2.
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 5/13
3.
4.
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 6/13
Ground  ng (Recommended)
The Power Adapter grounds the dev  ce; however, you can add opt  onal ESD ground  ng
for enhanced ESD protect  on.
1. Attach the Ground Screw to secure a ground w  re (not  ncluded) to the Ground  ng
Po  nt.
2. Opt  onal: To secure the Power Adapter cord,  nsert  t  nto the Cable Cl  p and secure
the Cable Cl  p us  ng the Ground Screw.
3. Secure the other end of the ground w  re to a ground  ng block.
Connect  ng Power
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 7/13
Connect the Power Adapter to the Power port and a power outlet.
Us  ng SFP Ports
1.
2.
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 8/13
3.
For  nformat  on about compat  ble f  ber SFP modules, v  s  t:
ubnt.l  nk/SFP_DAC_Compat  b  l  ty
Access  ng the EdgeOS Conf  gurat  on Interface
The EdgeOS® conf  gurat  on  nterface can be accessed v  a DHCP or stat  c IP address
ass  gnment. By default, eth1  s set up as a DHCP cl  ent, wh  le eth0  s ass  gned a stat  c IP
address of 192.168.1.1. To conf  gure the EdgeRouter, proceed to the appropr  ate
sect  on: DHCP or “Stat  c IP Address” .
DHCP
1. Connect an Ethernet cable from eth1 on the EdgeRouter to a LAN segment that has
an ex  st  ng DHCP server.
2. To check the IP address of the EdgeRouter, use one of the follow  ng methods:
Set up the DHCP server to prov  de a spec  f  c IP address to the EdgeRouter based
on  ts MAC address (on the label).
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 9/13
Let the EdgeRouter obta  n an IP address and then check the DHCP server to see
wh  ch IP address was ass  gned.
3. Launch your web browser. Enter the appropr  ate IP address  n the address f  eld. Press
enter (PC) or return (Mac).
4. Enter ubnt  n the Username and Password f  elds. Read the Ub  qu  t  L  cense
Agreement, and check the box next to I agree to the terms of th  s L  cense
Agreement to accept  t. Cl  ck Log  n.
The EdgeOS Conf  gurat  on Interface w  ll appear, allow  ng you to custom  ze your
sett  ngs as needed. For more  nformat  on, refer to the EdgeOS User Gu  de, wh  ch  s
ava  lable at u  .com/download/edgemax
Stat  c IP Address
1. Connect an Ethernet cable from the Ethernet port on your computer to the port
labeled eth0 on the EdgeRouter.
2. Conf  gure the Ethernet adapter on your host system w  th a stat  c IP address on the
192.168.1.x subnet.
3. Launch your web browser. Type https://192.168.1.1  n the address f  eld. Press enter
(PC) or return (Mac).
ER-12 Qu  ck Start Gu  de

18.02.2020 ER-12 Quck Start Gude
https://dl.ubnt.com/qsg/ER-12/ER-12_EN.html 10/13
4. Enter ubnt  n the Username and Password f  elds. Read the Ub  qu  t  L  cense
Agreement, and check the box next to I agree to the terms of th  s L  cense
Agreement to accept  t. Cl  ck Log  n.
The EdgeOS Conf  gurat  on Interface w  ll appear, allow  ng you to custom  ze your
sett  ngs as needed. For more  nformat  on, refer to the EdgeOS User Gu  de, wh  ch  s
ava  lable at
u  .com/download/edgemax
UNMS Management
You can manage your dev  ce us  ng UNMS, wh  ch lets you conf  gure, mon  tor, upgrade,
and back up your dev  ces us  ng a s  ngle appl  cat  on. Get started at www.unms.com
Spec  f  cat  ons
ER-12
D  mens  ons 268.1 x 136.5 x 31.1 mm
(10.55 x 5.37 x 1.22")
We  ght 700 g (1.54 lb)
Max. Power Consumpt  on 20W (Excludes PoE Output)
Power Method External AC/DC Power Adapter, 24W (24V, 1A)
(Included)
24V Pass  ve PoE
Power Supply External AC/DC Adapter
Pass  ve PoE 
Voltage Range DC/PoE Passthrough
Max. Wattage per Port 20W (24V)
Supported Voltage Range 9 - 30VDC
Button Reset
LEDs 
ER-12 Qu  ck Start Gu  de