Ubiquiti edgerouter X SFP User manual

Advanced Gigabit Router
with PoE and SFP
Model: ER-X-SFP

Introduction
Thank you for purchasing the Ubiquiti Networks®
EdgeRouter™X SFP. This Quick Start Guide is designed to guide
you through installation and also includes warranty terms.
Package Contents
EdgeRouter X SFP Power Adapter
(24V, 2.5A)
Advanced Gigabit Router
with PoE and SFP
Model: ER-X-SFP
Power Cord Quick Start Guide
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, indoor cabling requirements, and Dynamic Frequency Selection
(DFS) requirements.

Installation Requirements
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial‑grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable
WARNING: To reduce the risk of fire or electric shock, do
not expose the EdgeRouter X SFP to rain or moisture.
Note: Although the cabling can be located outdoors,
the EdgeRouter X SFP itself should be housed inside
a protective enclosure.
Hardware Overview
Front Panel
SFP (eth5/SFP) RJ45 (eth0-eth4)
Port Description
eth5/SFP The SFP port is hot-swappable and supports
a 100 Mbps or Gigabit fiber SFP module.
eth0‑eth4 RJ45 ports support passive 24V PoE output
and 10/100/1000 Ethernet connections.

Top Panel
Power PoE
Link/Act
LED State Status
Power
Status
Off Power Off
Green Power On
eth5
Link/Act
Off No Link
Green 100/1000Mbps (1 Gbps) Link
Flashing Indicates Activity
eth0‑eth4
PoE
Off No PoE
Green 24V Passive
Link/Act
Off No Link
Green 10/100/1000Mbps Link
Flashing Indicates Activity

Back Panel
Power
Ground
Reset
Button Description
Reset
There are two methods to reset the
EdgeRouter X SFP to factory defaults:
Runtime Reset (Recommended)
The EdgeRouter X SFP should be running after
bootup is complete. Press and hold the Reset
button for about 10 seconds until the eth4
Link LED starts flashing and then becomes
solidly lit. After a few seconds, the LED will
turn off, and the EdgeRouter X SFP will
automatically reboot.
Power-on Reset
1. Disconnect the Power Adapter from the
EdgeRouter X SFP.
2. Press and hold the Reset button while
connecting the Power Adapter to the
EdgeRouter X SFP. Keep holding the button
until the eth4 Link LED starts flashing and
then stops flashing after a few seconds.
Detail Description
Ground
The EdgeRouter X SFP is grounded through
the Power Adapter; however, you can add
optional ESD grounding for enhanced ESD
protection. The ground wire and screw with
washer are not included (recommended
screw size: M3-0.5 x 4 mm).
Power Connect the Power Adapter.

Hardware Installation
Place the EdgeRouter X SFP on a flat, horizontal surface or
mount it on a wall (mounting screws not included).
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
Connecting Power
1. Connect the Power Adapter to the Power port.
2. Connect the Power Cord to the Power Adapter. Connect the
other end of the Power Cord to a poweroutlet.

Connecting Ethernet
1. Connect an Ethernet cable from your computer or host
system to the port labeled eth0 on the EdgeRouter X SFP.
Note: PoE is disabled by default.
2. Connect Ethernet cables from the Ethernet ports of your
devices to the rest of the ports in this range: eth1‑eth4.

Using the SFP Port (Optional)
To use the eth5/SFP port:
1. Remove the protective plug covering the eth5/SFP port.
2. Plug a fiber SFP module into the eth5/SFP port.
1000Mbps SM/SC 20KM DDM
Tx1550nm/Rx1310nm
SN: 1 308 261 79
EF -1 000 M- 20 KM -1 5
3. Connect a fiber optic cable to the fiber SFP module. Then
connect the other end of the cable to another fiber device.
50
For information about compatible fiber SFP modules, visit:
community.ubnt.com/edgemax

Accessing the Configuration Interface
Note: Ensure that your host system is connected to the
eth0 port of the EdgeRouter X SFP.
1. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet.
2. Launch your web browser. Type https://192.168.1.1 in the
address field. Press enter (PC) or return (Mac).
3. The login screen will appear. Enter ubnt in the Username
and Password fields. Read the Ubiquiti License Agreement,
and check the box next to I agree to the terms of this License
Agreement to accept it. Click Login.
The EdgeOS Configuration Interface will appear, allowing
you to customize your settings as needed. You can click the
Wizards tab to access the Setup Wizards. For information on
PoE configuration, refer to the Configuring PoE Settings section.

Configuring PoE Settings
WARNING: Before activating 24V passive PoE, ensure
that the connected device supports PoE and the
suppliedvoltage.
1. On the Dashboard screen, go to Actions > PoE for the
interface you want to configure.
2. Select 24V from the PoE drop-down menu.
3. ClickSave.
For more information, refer to the EdgeOS User Guide, which is
available at documentation.ubnt.com/edgemax
*640-00150-02*
640-00150-02