Ubiquiti UFiber UF-WIFI Instruction manual

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 1/13
UF  ber UF-WIFI Screws (Qty. 4) Screw Anchors (Qty. 4)
Power Adapter (24V, 0.5A)
Package Contents
System Requ  rements
L  nux, Mac OS X, or M  crosoft W  ndows 7/8/10
Web Browser: Google Chrome (Other browsers may have l  m  ted funct  onal  ty)
Before You Beg  n
Des  gn  ng your f  rst GPON deployment requ  res spec  f  c knowledge and plann  ng. For
 nformat  on on GPON network des  gn and  nstallat  on,  nclud  ng  mportant
cons  derat  ons and best pract  ces, refer to:
ubnt.l  nk/UF  ber-GPON-Gett  ng-Started
ubnt.l  nk/Des  gn  ng-a-GPON-Network
For deta  ls on conf  gur  ng UF  ber dev  ces for the f  rst t  me to allow ONU LAN ports to
prov  de connect  v  ty, refer to: ubnt.l  nk/UF  ber-In  t  al-Conf  gurat  on
Hardware Overv  ew
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com
all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 2/13
PON Port
LAN (Ports 1 - 4)
Reset Button
Power Port
SC/APC GPON port supports WAN connect  ons of 2.488 Gbps downstream and
1.244 Gbps upstream.
RJ45 Ethernet LAN ports support 10/100/1000 Mbps connect  ons. Port 1 also
supports 24V Pass  ve PoE to power the dev  ce.
The Reset button serves two funct  ons for the UF-WIFI:
Restart Press and release the Reset button qu  ckly. The three s  gnal LEDs w  ll
ash amber.
Restore to Factory Default Sett  ngs Press and hold the Reset button for more
than f  ve seconds.
The Power Adapter connects to th  s port to prov  de power.
Wh  te Ethernet connect  on up
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 3/13
S  gnal LEDs
Ethernet LED
Off Bootup
S  gnal strength: low
≥ -28 dBm
S  gnal strength: good
≥ -25 dBm
S  gnal strength: strong
≥ -11 dBm
S  gnal strength: too low
< -28 dBm
Check the qual  ty of the f  ber connect  on, and
calculate the total opt  cal loss of the opt  cal
spl  tters.
S  gnal strength: too strong
≥ -8 dBm
Add an opt  cal spl  tter, or add a 5 or 10 dB
opt  cal attenuator.
No s  gnal
Check the f  ber cables and connectors, and
ensure that the OLT funct  ons properly.
No author  ty
The UF-WIFI has not been author  zed or cannot
commun  cate w  th the OLT. Check passwords
and OLT sett  ngs.
Off Ethernet connect  on down
Wh  te Ethernet connect  on up
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 4/13
Power LED
Flash  ng  nd  cates act  v  ty
Off Power off
Wh  te Power on
Hardware Installat  on
Wall Mount  ng
1.
2.
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 5/13
3.
4.
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 6/13
Connect  ng F  ber
WARNING: Never look d  rectly  nto the ends of f  ber or modules. The em  tted
l  ght could cause damage to the eye.
WARNING: Unt  l ready for use, keep modules and f  ber patch cables covered
us  ng the  ncluded protect  ve caps to ensure the connect  ons stay clean.
WARNING: Do NOT connect the dev  ce d  rectly to a UF  ber GPON module (UF-
GP-B+ or UF-GP-C+). Do  ng so w  ll damage the dev  ce opt  cs. Ensure that the
dev  ce’s rece  ved s  gnal level never exceeds -8 dBm. Use a UF  ber PLC Spl  tter to
add attenuat  on as needed.
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com
all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 7/13
Connect  ng LAN
Connect  ng Power
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 8/13
OR
Note: 24V Pass  ve PoE  s requ  red to power the dev  ce.
WARNING: The PoE sw  tch must comply w  th the power spec  f  cat  ons l  sted  n
the Spec  f  cat  ons sect  on of th  s Qu  ck Start Gu  de.
Access  ng the Conf  gurat  on Interface
1. Ensure that your computer (or other host system)  s connected to the dev  ce.
2. Conf  gure the Ethernet adapter on your host system w  th a stat  c IP address on the
192.168.1.x subnet.
3. Launch your web browser. Type http://192.168.1.1  n the address f  eld. Press enter
(PC) or return (Mac).
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 9/13
4. Enter ubnt  n the Username and Password f  elds. Cl  ck Log  n.
Custom  ze sett  ngs as needed. For more  nformat  on, refer to the UF  ber resources,
wh  ch are ava  lable at: http://ubnt.l  nk/UF  ber-Support
Spec  f  cat  ons
UF-WIFI
D  mens  ons 126.34 x 126.09 x 31.65 mm
(4.97 x 4.96 x 1.25")
We  ght 190 g (6.70 oz)
Network  ng Interfaces (1) SC/APC, GPON WAN
(4) G  gab  t RJ45, Ethernet LAN
(1) W  -F  , 802.11n
Network  ng Interface Speeds
GPON WAN, ITU G.984 2.4 Gbps Down, 1.2 Gbps Up
LAN 10/100/1000 Mbps
W  -F  300 Mbps
Management Interface In-Band Ethernet
PON
Normal Opt  cal Power Range TX (Class B+): 1.5 to 5 dBm
RX: -28 to -8 dBm
Power Method DC Jack, 24VDC
24V Pass  ve PoE (P  ns 4, 5+; 7, 8-)
Power Supply 100-240VAC / 50-60 Hz Un  versal AC/DC
24V / 0.5A
Max. Power Consumpt  on 7W
Supported Voltage Range 20 to 28V
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

19.02.2020 UF-WIFI Quck Start Gude
https://dl.u.com/qsg/UF-WIFI/UF-WIFI_EN.html 10/13
UF-WIFI
Processor Specs MIPS, 900 MHz
Memory Informat  on 256 MB DDR
Button (1) Reset
Operat  ng Temperature -10 to 45° C (14 to 113° F)
Operat  ng Hum  d  ty 10 to 90% Noncondens  ng
Cert  f  cat  ons CE, FCC, IC
Safety Not  ces
1. Read, follow, and keep these  nstruct  ons.
2. Heed all warn  ngs.
3. Only use attachments/accessor  es spec  f  ed by the manufacturer.
WARNING: To reduce the r  sk of f  re or electr  c shock, do not expose th  s product to ra  n
or mo  sture.
WARNING: Do not use th  s product  n locat  on that can be submerged by water.
WARNING: Avo  d us  ng th  s product dur  ng an electr  cal storm. There may be a remote
r  sk of electr  c shock from l  ghtn  ng.
WARNING: CLASS 1 LASER PRODUCT - Do not look  nto the ends of the f  ber opt  c cable
or SFP modules wh  le converters are powered.
Electr  cal Safety Informat  on
1. Compl  ance  s requ  red w  th respect to voltage, frequency, and current requ  rements  nd  cated
on the manufacturer’s label. Connect  on to a d  fferent power source than those spec  f  ed may
result  n  mproper operat  on, damage to the equ  pment or pose a f  re hazard  f the l  m  tat  ons
are not followed.
2. There are no operator serv  ceable parts  ns  de th  s equ  pment. Serv  ce should be prov  ded only
by a qual  f  ed serv  ce techn  c  an.
L  m  ted Warranty
u  .com/support/warranty
The l  m  ted warranty requ  res the use of arb  trat  on to resolve d  sputes on an  nd  v  dual bas  s, and,
where appl  cable, spec  fy arb  trat  on  nstead of jury tr  als or class act  ons.
Compl  ance
FCC
UF-WIFI Qu  ck Start Gu  de
All manuals and user guides at all-guides.com