Ubiquiti POE-50-60W User manual

PoE injector
power input
Power cord
PoE y LAN
POE-50-60W Quick Start Guide
hardware description
Package content
Puerto

Installation
1. Connect a network cable to the PoE port on the injector and the other end to the Ubiquiti device
you want to power (see device specifications).
switch de su red local.
stream.
4. Optionally, the PoE injector can be fixed to the wall or some other surface, follow the instructions
in the following image.
2. Connect a network cable to the LAN port of the injector and the other end to the router or
3. Connect the power cord to the injector and the other end to an electrical outlet.

specs
1500A (8/20 µs) Potencia
clamping protection
LAN activity
AC connector
output voltage
<5pF data
Certifications
Puerto LAN Gigabit
rated voltage
Dimensions
reset button
bypass capacity
Input current
4 pair feeding
Storage temperature
inrush current
2 pair feeding
Pins 3, 6, 7, 8 (-)
load regulation
line regulation
192 g (6.77 ounces)
Model
Operating temperature
output ripple
operating humidity
maximum pulse current
Response time
max surge discharge
No
No
Weight
–
Yes
ÿ 3%
ÿ 5%
No
85+%
0 a 40 °
65kHz
° C (32 a 104 F)
difference and common mode
surge protection
<200A Pico @ 230VAC
35 to 95% non-condensing
RJ45 shielded socket
<1 ns
CEI-320 C6
°°
POE-50-60W, POE-50-60W-WH
<100A Pico @120VAC,
Efficiency
- 30 a 70 C (-22 a 158
1% max
F)
Data entry / POE
11 V data, 60 V power
remote reset
Indicator
0,75 A a 230 V CA
change frequency
Ability
Pins 1, 2, 4, 5 (+) and
1,3 A a 120 V CA,
(3,98 x 2,36 x 1,30”)
36A (10/1000 µs) Data
101 x 60 x 33 mm
50 V CC a 1,2 A
CE, FCC, CI, UL
100-240 V CA a 50/60 Hz

2. Pay attention to all warnings.
1. It is mandatory to comply with the current, frequency and voltage requirements indicated on the manufacturer's
label. Connection to a power source other than those specified may result in malfunction, equipment damage, or fire
hazard if limitations are not followed.
1. Read, follow and save these instructions.
If you have any questions about the installation, contact a qualified electrician or the manufacturer
before connecting the equipment.
The indicated AC adapter provides a safety ground. For installation in a building, adequate short-circuit
back-up protection must be provided.
The equipment requires the use of the ground wire as part of the safety certification. Modification or
misuse can create a shock hazard, which could cause serious injury or death.
and. A protective connection must be installed in accordance with national wiring rules and regulations.
d.
3. This equipment is supplied with a detachable power cord that has an integral safety ground wire designed to be
connected to a safety ground. a. Do not substitute the power cord with one other than the approved type provided.
Never use an adapter plug to connect to a two-wire outlet, as it will break the continuity of the ground wire.
3. Only use the devices or accessories indicated by the manufacturer.
2. This equipment contains no operator-serviceable parts. Only a qualified service technician should provide services.
c.
b.
electrical safety information
safety instructions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1.This device may not cause harmful interference.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
The limited warranty requires arbitration to resolve disputes on a case-by-case basis and, where
appropriate, specifying arbitration instead of jury trials or class actions.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide acceptable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his own
expense.
2.This device must accept any interference received, including interference that may cause
undesired operation.
ui.com/support/warranty
Compliance
CE marked
limited warranty
FCC