ULTIMATE SPEED ULG 17 A1 User manual

CAR BATTERY CHARGER &
JUMP STARTER
Operation and Safety Notes
Translation of the original instructions
GB
AKKUMULÁTORTÖLTŐ
INDÍTÓFUNKCIÓVAL
Kezelési és biztonsági hivatkozások
Az eredeti használati utasítás fordítása
HU
POLNILNIK ZA AKUMULATORJE
MOTORNIH VOZIL S FUNKCIJO
ZAGONA VOZILA
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
SI
AUTONABÍJEČKA S FUNKCÍ
POMOCNÉHO STARTOVÁNÍ
Návod k obsluze a bezpečnostní pokyny
Originální návod k obsluze
CZ
AUTONABÍJAČKA SFUNKCIOU
POMOCNÉHO ŠTARTOVANIA
Návod na obsluhu a bezpečnostné upozornenia
Originálny návod na obsluhu
SK
KFZ-BATTERIELADEGERÄT MIT
STARTHILFEFUNKTION
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
DE AT CH
CAR BATTERY CHARGER & JUMP STARTER
ULG 17 A1
IAN 425898_2301 SK
SI
CZ
HU

GB
Before reading, unfold the page containing the illustrations and familiarise yourself with all
functions of the device.
HU
Olvasás előtt hajtsa ki az ábrát tartalmazó oldalt, és ezután ismerje meg a készülék
mindegyik funkcióját.
SI
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
CZ
Než začnete číst tento návod k obsluze, rozložte stránku s obrázky a seznamte se se všemi
funkcemi zařízení.
SK
Prv než začnete čítať tento návod, rozložte si stranu s obrázkami a potom sa oboznámte so
všetkými funkciami zariadenia.
DE AT CH
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich
anschließend mit allen Funktionen des Gerätes vertraut.
GB Operation and Safety Notes Page 5
HU Kezelési és biztonsági hivatkozások Oldal 19
SI Navodila za upravljanje in varnostna opozorila Stran 35
CZ Návod k obsluze a bezpečnostní pokyny Strana 50
SK Návod na obsluhu a bezpečnostné upozornenia Strana 64
DE/AT/CH Montage-, Bedienungs- und Sicherheitshinweise Seite 78

A
B
1 2 3 4
567
8

GB 5
zTable of pictograms used
Read the operating instructions for
this product attentively and with
care before use.
~ 50 Hz Alternating voltage with a frequency
of 50 Hz
PLEASE NOTE: This symbol
indicates additional information and
explanations on the product and
its use.
Caution! Possible risks!
Caution! Risk of electric shock! Caution! Explosion hazard!
You are legally obliged to place
devices marked as such in a collec-
tion which is separate from unsorted
municipal waste. Disposal through
household waste is prohibited.
IP20
Protection class IP20: Protection from
the device housing against touching
live or internal moving parts with
your fingers.
Suitable for lead-acid battery:
8 Ah – 250 Ah Do not dispose of any electrical devices in domestic waste!
Only for use in closed,
ventilated rooms!
Dispose of the device and
packaging in an environmentally
friendly manner!
Table of pictograms used ........................................................................................Page 5
Introduction ..............................................................................................................Page 6
Intended use .............................................................................................................Page 6
Scope of delivery.......................................................................................................Page 6
Parts description ........................................................................................................Page 7
Technical Specifications..............................................................................................Page 7
Safety instructions ...................................................................................................Page 7
Operation .................................................................................................................Page 11
Product properties......................................................................................................Page 11
Connecting to use the charging modes.........................................................................Page 11
Disconnecting after using the charging modes...............................................................Page 11
Select charging mode and start charging process ..........................................................Page 11
Using the jump-start function........................................................................................Page 13
Alternator test function................................................................................................Page 14
Replacing the fuse .....................................................................................................Page 14
Maintenance and care.............................................................................................Page 14
Information about recycling and disposal.............................................................Page 14
Original EC Declaration of Conformity...................................................................Page 15
Warranty and service information.........................................................................Page 16
Warranty conditions...................................................................................................Page 16
Warranty period and statutory claims for defects...........................................................Page 16
Extent of warranty......................................................................................................Page 17
Processing of warranty claims .....................................................................................Page 17
Service.......................................................................................................................Page 18

6GB
Packaging material –
corrugated paper Suitable for cars
Suitable for motorcycles Suitable for the charging of
6 V batteries
Suitable for the charging of
12 V batteries Made from recycled material
Car battery charger & jump starter ULG 17 A1
zIntroduction
Congratulations! You have purchased one of our high-quality products. Please familiarise
yourself with the product before using it for the first time. Read the following original
operating and safety instructions carefully. This product must be set up or used only by
people who have been trained to do so.
zIntended use
The Ultimate Speed ULG 17 A1 is a car battery charger with pulse maintenance charge (chip software),
used for charging and maintenance charging and suitable for the following 6V or 12V lead batteries
(batteries) with electrolyte solution, AGM batteries, lead-acid batteries, deep cycle (e.g. boat batteries)
or gel batteries:
 For car and motorcycle batteries with 12 V / 6 V and 8–250 Ah capacity
You can also regenerate discharged batteries (depending on the battery type). The car battery charger has
a safety circuit against sparking and overheating. Keep these instructions in a safe place. Ensure you hand
over all documentation when passing the product on to anyone else. Any use that differs to the intended
use as stated above is prohibited and potentially dangerous. Damage or injury caused by misuse or disre-
garding the above warning is not covered by the warranty or any liability on the part of the manufacturer.
The device is not intended for commercial use. Commercial use will void the guarantee.
PLEASE NOTE: The car battery charger cannot charge any electrical vehicles with integrated
rechargeable battery.
PLEASE NOTE: No jumpstart of 6 V batteries possible.
zScope of delivery
PLEASE NOTE: Check the scope of delivery and the device as well as all parts for damage
immediately after unpacking. Do not put a defective unit or defective parts into operation.
1 Car battery charger Ultimate Speed ULG 17 A1
2 quick-contact connection terminals, (1 red, 1 black)
1 original operating instructions

GB 7
zParts description
For this, see Fig. A and B:
1Digital Display button
2Battery Type button
3Charge Start button
4“–” pole connection terminal (black)
5“+” pole connection terminal (red)
6Digital display
7Mains cable
8Fuse with cover
PLEASE NOTE: The use of the term “product” or “device” in the following text refers to the
car battery charger named in these operating instructions.
zTechnical Specifications
Input voltage: 230 V ~ 50 Hz
Return current*: < 5mA (no AC input)
Nominal output voltage: 6V/12V
Charge current: 2A, 6A, 17 A ± 10%
Battery type with: 12V/6V and 8–250Ah capacity
Housing protection type: IP 20
* = Return current means the current that the car battery charger consumes from the battery when no
mains current is connected.
Changes to technical and visual aspects of the product may be made as part of future developments
without notice. Accordingly, no warranty is offered for the physical dimensions, information and speci-
fications in these operating instructions. The operating instructions cannot therefore be used as the basis
for asserting a legal claim.
PLEASE NOTE: The maximum load current essentially depends on the internal resistance of the
connected battery. This internal resistance is determined by the following factors: ages, capacity and
type of connected battery.
zSafety instructions
KEEP OUT OF THE REACH OF CHILDREN!
 DANGER! Avoid danger to life and danger of injury from
improper use!

8GB
 CAUTION! Do not operate the device with a damaged cable,
mains cable or mains plug. Damaged mains cables pose danger
to life from electric shock.
 In case of damage, the mains cable must only be repaired by
authorized and trained specialists! Contact the service point of
your country if you need any repairs!
 RISK OF ELECTRIC SHOCK! Ensure that the vehicle is not in
operation if the battery is installed firmly in the vehicle! Switch off the
ignition and put the vehicle into the parking position, with the parking
brake engaged (e.g. car) or the rope attached (e.g. boat)!
 RISK OF ELECTRIC SHOCK! Disconnect the car battery
charger from the mains before removing the connection terminals.
 First connect the connection terminal that is not connected to the
car body.
 Connect the other connection terminal to the car body away from
the battery and the petrol line.
 Connect the car battery charger to the supply grid only after doing
this.
 Disconnect the car battery charger from the supply grid after
charging.
 Only then disconnect the connection terminal from the car body.
Then disconnect the connection terminal from the battery.
 RISK OF ELECTRIC SHOCK! Only touch the pole
connection cables (“–” and “+”) in the insulated area!
 RISK OF ELECTRIC SHOCK! Conduct the connection to
the battery and the socket of the mains grid completely protected
from moisture!
 RISK OF ELECTRIC SHOCK! Perform installation, servicing
and maintenance of the car battery charger only when the mains
current is not connected!
 RISK OF ELECTRIC SHOCK! First disconnect the
negative pole connection cable (black) of the car battery charger
from the negative pole of the battery upon completing the charging
and trickle charging process, if the battery is continually connected
in the vehicle.

GB 9
 Do not leave any toddlers or children unsupervised around the
car battery charger!
 Children cannot assess possible dangers in use of electrical
devices. Children must be supervised to ensure that they do not
play with the device.
 This device may be used by children aged 8 years and older,
and by persons with reduced physical, sensory or mental capacities,
or a lack of experience and knowledge, if they are supervised or
have been instructed in how to use the device safely and understand
the dangers that may arise when using it. Do not allow children to
play with the device. Cleaning and day-to-day maintenance must not
be performed by children without supervision.
 EXPLOSION HAZARD! Protect yourself from highly
explosive oxyhydrogen reactions! Gaseous hydrogen can escape
during charging or maintenance charging of the battery. Oxyhydro-
gen is a potentially explosive mix of gaseous hydrogen and oxygen.
The oxyhydrogen reaction occurs on contact with open fire (flames,
smouldering or sparks)! Perform charging and maintenance charg-
ing in a weather-protected space that is ventilated well. Ensure that
there are no naked flames (flames, embers or sparks) during charg-
ing or maintenance charging!
 EXPLOSION AND FIRE HAZARDS! Ensure that explosive
or flammable substances, such as petrol or solvents cannot be
ignited when you are using the car battery charger!
 EXPLOSIVE GASES! Avoid flames and sparks!
 Ensure sufficient ventilation when charging.
 Put the battery onto a well-ventilated surface when charging.
Otherwise, the device can be damaged.
 EXPLOSION HAZARD! Ensure that the positive pole
connection cable has no contact with a fuel line (e.g. petrol line)!
 DANGER OF CAUSTIC BURNS! Protect your eyes and skin
from caustic burns from the acid (sulphuric acid) when it comes
into contact with the battery!
 Use: acid-resistant safety goggles, clothing and gloves! If your eyes
or skin have come into contract with the sulphuric acid, flush the
affected body region with plenty of clear, running water and seek
medical advice at once!

10 GB
 Avoid electrical short circuits when connecting the car battery
charger to the battery. Connect the negative pole connection
cable only to the negative pole of the battery or the car body.
Connect the positive pole connection cable only to the positive
pole of the battery!
 Before connecting to the mains, verify the mains power has the
required 230 V~ 50 Hz, neutral lead, a 16 A fuse and an ELCB
switch (earth leakage circuit breaker)! Otherwise, the device can
be damaged.
 Do not use the car battery charger near any fires, heat and long-
term temperatures above 50°C! For higher temperatures, the output
power of the car battery charger will drop automatically.
 Only use the car battery charger with the original parts it was
delivered with!
 Do not cover the car battery charger with any objects!
Otherwise, the device can be damaged.
 Protect the electrical contact surfaces of the battery from short circuit!
 Only use the car battery charger for the charging and maintenance
charging of undamaged 6V/12V lead batteries (with electrolyte
solution or gel)! Otherwise, property damage may be the conse-
quence.
 Do not use the car battery charger for the charging and
maintenance charging of non-rechargeable batteries.
Otherwise, property damage may be the consequence.
 Do not use the car battery charger for the charging and
maintenance charging of damaged or frozen batteries!
Otherwise, property damage may be the consequence.
 Please refer to the original operating instructions about the mainte-
nance of your battery prior to connecting the car battery charger!
Otherwise, there is a danger of injury and/or the risk of damage
to the device.
 Before connecting the car battery charger to a battery that is
continually connected to the vehicle, learn about compliance with
the electrical safety and maintenance in the original operating
instructions of the vehicle! Otherwise, there is a danger of injury
and/or the risk of property damage.
 Disconnect the car battery charger from the mains current when it
is not is use, to protect the environment as well! Note that power is
consumed in standby operation as well.
 Always pay attention and be aware of what you are doing.
Proceed reasonably and do not put the car battery charger into
operation when you are not focused or not feeling well.

GB 11
zOperation
Always unplug the mains plug from the socket before you perform any work at the
car battery charger or leave the device unattended.
RISK OF ELECTRIC SHOCK! DANGER OF PROPERTY DAMAGE! RISK OF INJURY!
zProduct properties
This device is designed for charging many SLA batteries (sealed lead-acid batteries), which are used
primarily in cars, motorcycles and some other vehicles. They can be, e.g., WET (with liquid electrolyte),
GEL (with electrolyte gel) or AGM batteries (with electrolyte-absorbent mats). A special design of the
device (also called a “three-stage charging strategy”) permits recharging of the battery to nearly 100%
of its capacity. The battery may also be permanently connected to the car battery charger in order to
keep it in optimal condition at all times. Furthermore, the battery charger has an integrated temperature
sensor in the device in order to safely recharge the battery even in cold weather (e.g. in the winter).
The device measures the ambient temperature and automatically sets the optimal charging voltage.
PLEASE NOTE: The ambient temperature is measured in the charger. Hence, for optimum function,
make sure the battery exhibits the same temperature as the environment.
zConnecting to use the charging modes
 Disconnect the negative pole connection cable (black) of the vehicle from the negative pole of the
battery first before charging and maintenance charging if the battery is continually connected in the
vehicle. The negative pole of your battery is usually connected to the car body of the vehicle.
 Then disconnect the positive pole connection cable (red) of the vehicle from the positive pole of the
battery.
 Only then connect the “+” pole quick-contact connection terminal (red) 5of the car battery charger
to the “+” pole of the battery.
 Connect the “–” pole quick-contact connection terminal (black) 4to the “–” pole of the battery.
Connect the mains cable 7of the car battery charger to the socket.
PLEASE NOTE: If the connection terminals are connected correctly, the digital display 6indicates
the voltage and the “connected” display lights up. In the event of reverse polarity, the display will show
0.0 and the reverse polarity LED will light up in red in the digital display 6.
zDisconnecting after using the charging modes
 Disconnect the device from the mains current.
 Disconnect the “–” pole quick-contact connection terminal (black) 4from the “–” pole of the battery.
 Disconnect the “+” pole quick-contact connection terminal (red) 5from the “+” pole of the battery.
 Reconnect the positive pole connection cable of the battery to the positive pole of the battery.
 Reconnect the negative pole connection cable of the battery to the negative pole of the battery.
zSelect charging mode and start charging process
You can choose from different charging modes to charge different batteries. As compared to conventional
car battery chargers, this device has a special function for reuse of a flat battery/rechargeable battery.
You can recharge a completely discharged battery/rechargeable battery. Protection against wrong
connection and short circuit ensures safe charging. The integrated electronics do not start the car battery
charger at once after connection of the battery, but only after a charging mode has been selected.

12 GB
If the connection terminals are connected to the battery and the device is connected to the mains,
the digital display 6will show the “Connected” display. Once the charging mode has been selected
with the charge start button 3, the “Charging” display will light up. When charging is complete,
the “Charged” display lights up. If the digital display “0.0” is continually lit before the battery is
completely charged, there is a defect.
 In this case, check again if the connection terminals 4, 5are correctly attached to the battery and
whether the correct battery type has been chosen. If the display continually shows “0.0”, there may
be a defect in the battery.
Reactivation function / reconditioning:
If a voltage between 8.5 V and 10.5 V is detected in the connected battery, the device will automatically
start a reconditioning process in order to reactivate the battery. If a voltage between 8.5V and 10.5V is
measured after the reconditioning process, then “Err” will be shown on the digital display. In this case,
the battery is faulty and must be replaced.
PLEASE NOTE: This function is only available for 12 V batteries.
Digital Display button 1:
Enables the switch between the digital display of the voltage and charging progress in percent
(Battery %). Use this button to switch between the following displays:
 Battery %: shows the charging progress of the connected battery in percent.
 Voltage: shows the voltage of the connected battery.
 Alternator % check: Output power of the alternator in percent.
Battery Type button 2:
Use this button to set the battery type to be charged. You can choose between different battery types.
The battery type must be correctly set before starting the charging process:
 12 V Regular: These batteries (lead-acid batteries) are usually used in cars, trucks and motorcycles.
They have venting caps and are often marked as “low-maintenance” or “no maintenance”. This battery
type is meant for transferring energy quickly (e.g. starting an engine). “Regular” batteries should not be
used for “Deep-Cycle/Marine” applications.
 12 V Deep-Cycle: These batteries are usually also marked as “Deep-Cycle” or “Marine”.
Batteries of this type are usually larger than other battery types. This supplies less short-term energy,
but a longer-term energy transmission. These batteries can withstand a large number of discharge
cycles.
 12 V AGM/Gel: The AGM battery types are usually good deep-cycle batteries. They have the best
“service life” if they are recharged before they have been discharged by more than 50%.
At complete discharge they can withstand about 300 charge cycles. The battery type GEL is similar to
the battery type AGM. The voltage at recharging is lower than in other lead-acid batteries.
If you use the wrong car battery charger for a gel battery, a reduced output or shorter service life can
be expected.
 6 V Regular: Choose this mode for commercial rechargeable 6 V batteries. Charge current 2A
PLEASE NOTE: If you connect a 12 V car battery to a car battery charger and the car battery
charger automatically detects it as a 6 V battery, it can be assumed that this 12 V car battery is faulty
and needs to be replaced.
Charge Start button 3:
Use this button to switch between the following options and start the charging process:
 Fast Charge: fast charging

GB 13
 Normal charge: normal charging (normal speed)
 Start: briefly supplies 75 Ampere to bridge batteries with a weak charge or flat 12 V batteries for
the purpose of starting the engine
PLEASE NOTE: In the Fast Charge mode the charger automatically switches to maintenance charging
after a successful charging process (the “Charged” LED lights up in green in the digital display
6
),
provided the car battery charger remains connected to the battery and mains current.
ATTENTION: Mode can only be terminated by unplugging the mains plug 7or by repeatedly
pressing the charge start button 3(repeated pressing until no mode is displayed).
PLEASE NOTE: If the “Charged” LED in the digital display 6lights up in green, the battery is
sufficiently charged and a repeated fast or normal charging process is no longer permitted.
zUsing the jump-start function
Always make all connections as described and in the proper order.
Otherwise, the electronic system of the vehicle can be damaged. If proceeding contrary to the
specifications described, you will act at your own risks and responsibility.
ATTENTION: This function is not suitable for batteries below 45 Ah. For batteries below 45 Ah,
this function may damage the battery. For diesel vehicles and large-volume petrol motors, higher currents
than 75 A are needed for starting at times.
PLEASE NOTE: The car battery charger has an analysis program that protects the battery
from damage, particularly for the jump-start function (e.g. sulphatisation, excessive voltage drops).
If the batteries are discharged very heavily or subject to very high stress, the device will not activate
the jump starter to protect the battery. During this process, the battery is already being charged at low
currents (“charging” is lit). The display then stays at “0”. In this case, jump starting is not possible.
This protects the battery from damage. The battery should be charged first. The function “Fast Charge”
or “Normal Charge” can be used for this.
 Connect the “+” pole quick-contact connection terminal (red) 5of the car battery charger to the “+”
pole of the battery.
 Connect the “–” pole quick-contact connection terminal (black) 4to the “–” pole of the battery.
Connect the mains cable 7of the car battery charger to the socket.
 If the connection terminals are correctly connected, the car battery charger will automatically choose
the correct 6 V or 12 V voltage. You can review the battery type in the “Battery Type” option field
and if necessary change it by pressing the battery type button 2.
 Now use the Charge Start button 3to select the function “Start”. The car battery charger now
analyses the charge condition of the battery. The display will now read “0”.
 Now actuate the vehicle's ignition. The display will now show a 5 second countdown (of which
2second priming / analysis function and 3 second jump-start function at 75 A) when the car battery
charger is used for jump starting (previously analysed by the car battery charger). During this
countdown, your car battery charger will briefly supply 75 A, in order to bridge the battery for the
purposes of starting the engine. Start the motor during the countdown. This will be followed by a
break of 180 seconds to protect the battery. Now the cycle restarts (2 seconds lead or analysis
function and 3 seconds jump-start function at 75A / 180 seconds pause).
 To disconnect the device, first remove the connection terminals first ( 4/ 5) and then unplug the
mains cable 7.
PLEASE NOTE: If the battery is discharged entirely, the 75 A will not be sufficient to start the
engine in all vehicles (e.g. diesel vehicles).

14 GB
 In this case, use the Charge Start button 3to select the option “Fast Charge” and then charge the
battery to 60% (for diesel engines, the warm-up withdraws energy from the battery. The 60% must
be pending after warm-up).
 You can track charging progress at the display by selecting the option “Battery %” with the digital
display button 1.
 When 60% is reached, repeat the jump-start function.
ATTENTION: End the mode by unplugging the mains plug 7.
zAlternator test function
 Attach the red connection terminals 5to the positive pole of your battery. The positive pole is
marked by a “+” and a red mark.
 Attach the black connection terminals 4to the negative pole of your battery. The negative pole is
marked by a “–” and a black mark.
 Connect the mains cable 7of the car battery charger to the socket.
Set the “Alternator” function (LED next to the alternator) via the button
1
. A % value is displayed. Start the
engine. If the % value rises with the engine running, the alternator will charge the battery. If the %value
drops or remains the same, there is a problem with the alternator, the connection or the battery.
 Disconnect the device from the mains current.
 Disconnect the “–” pole quick-contact connection terminal (black) 4from the “–” pole of the battery.
 Disconnect the “+” pole quick-contact connection terminal (red) 5from the “+” pole of the battery.
zReplacing the fuse
The fuse of the car battery charger may be damaged, e.g. by a device defect, overload, etc.
 Before replacing the fuse, unplug the mains cable 7.
 Remove the cover of the fuse 8by depressing it slightly on the side.
 Unscrew the fuse with a suitable open-end spanner and secure the new fuse.
 Screw it on subsequently and replace the cover 8.
PLEASE NOTE: If you need a new fuse, contact our service (see chapter with warranty and service
information).
zMaintenance and care
 Always unplug the mains cable 7from the socket before you perform any work on the car battery
charger.
 The device is maintenance-free. Deactivate the device. Clean the metal and plastic surfaces of the
device with a dry cloth.
 Never use any solvents or other aggressive cleaning agents.
zInformation about recycling and disposal
DO NOT DISPOSE OF ELECTRICAL TOOLS IN HOUSEHOLD WASTE! DON’T
THROW AWAY – RECYCLE!
According to European Directive 2012/19/EU, used electrical devices must be collected separately
for environmentally compatible recycling or recovery. The symbol of the crossed out dustbin means that
this device must not be disposed of in household waste at the end of its service life. The device must be
handed in at established collection points, recycling centres or waste management depots.

GB 15
The disposal of defective devices which you have sent in will be carried out free of charge. In addition,
distributors of electrical and electronic equipment as well as food distributors are obliged to accept
returned waste. Lidl provides you with return options directly in its branches and shops. Return and
disposal is free of charge for you. When buying a new device you have the right to return an equivalent
old device at no charge. In addition you have the option, regardless of whether you are buying a new
device, to hand in (up to three) old devices at no charge, as long as the device is no larger than 25 cm
in any dimension. Before returning the device please delete all personal information. Before returning,
please remove batteries or rechargeable battery packs which are not enclosed by the old device, as well
as bulbs, which can be removed without destroying the product and take these to a separate collection
point.
Batteries containing harmful substances are labelled with the adjacent symbol, which indicates
the prohibition on disposal in household waste. The abbreviations for the relevant heavy metals
are: Cd = cadmium, Hg = mercury, Pb = lead.
Take used batteries to a waste management company in your city or community or return them to your
dealer. This satisfies your legal obligations while also making an important contribution to protecting the
environment.
Please note the marking on the different packaging materials and separate them as necessary.
The packaging materials are marked with abbreviations (a) and digits (b) with the following
definitions: 1–7: Plastics, 20–22: Paper and cardboard, 80–98: Composite materials.
zOriginal EC Declaration of Conformity
We,
C. M. C. GmbH Holding
Responsible for documentation:
Dr. Christian Weyler
Katharina-Loth-Str. 15
66386 St. Ingbert
Germany
hereby take sole responsibility for declaring that the product
Car battery charger & jump starter ULG 17 A1
IAN: 425898_2301
Art. no.: 2604
Year of manufacture: 2023/39
Model: ULG 17 A1
meets the basic safety requirements as specified in the European Directives
Low Voltage Directive:
(2014/35/EU)
Electromagnetic Compatibility:
(2014/30/EU)
RoHS Directive:
(2011/65/EU)+(2015/863/EU)

16 GB
and the amendments to these Directives.
The object of the declaration described above meets the requirements of Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous
substances in electrical and electronic equipment.
This conformity assessment is based on the following harmonised standards:
EN 60335-1:2012/A15:2021
EN 60335-2-29:2021/A1:2021
EN 62233:2008
EN 50498:2010
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 61000-3-2:2019/A1:2021
EN 61000-3-3:2013/A2:2021
St. Ingbert, 01 March 2023
Dr. Christian Weyler
- Quality Assurance -
zWarranty and service information
Warranty from C.M.C GmbH Holding
Dear Customer,
The warranty for this equipment is 3 years from the date of purchase. In the event of product defects,
you have legal rights against the retailer of this product. Your statutory rights are not affected in any way
by our warranty conditions, which are described below.
zWarranty conditions
The warranty period begins on the date of purchase. Please retain the original sales receipt.
This document is required as your proof of purchase.
Should this product show any defect in materials or manufacture within 3 years from the date of purchase,
we will repair or replace it – at our discretion – free of charge. This warranty service requires that you
retain proof of purchase (sales receipt) for the defective device for the three year period and that you
briefly explain in writing what the fault entails and when it occurred.
If the defect is covered by our warranty, we will repair and return your product or send you a replacement.
The original warranty period is not extended when a device is repair or replaced.
zWarranty period and statutory claims for defects
The warranty period is not extended by the guarantee. This also applies to replaced and repaired parts.

GB 17
Any damages or defects detected at the time of purchase must be reported immediately after unpacking.
Any incidental repairs after the warranty period are subject to a fee.
zExtent of warranty
This device has been manufactured according to strict quality guidelines and carefully inspected before
delivery.
The warranty applies to material and manufacturing defects only. This warranty does not extend to
product parts, which are subject to normal wear and tear and can thus be regarded as consumable
parts, or for damages to fragile parts, e.g. switches, rechargeable batteries or parts made from glass.
This warranty is voided if the product becomes damaged or is improperly used or maintained.
For proper use of the product, all of the instructions given in the operating instructions must be followed
precisely. If the operating instructions advise you or warn you against certain uses or actions, these must
be avoided in all circumstances.
The product is for consumer use only and is not intended for commercial or trade use. The warranty becomes
void in the event of misuse and improper use, use of force, and any work on the device that has not been
carried out by our authorised service branch.
zProcessing of warranty claims
To ensure prompt processing of your claim, please follow the instructions given below.
Please retain proof of purchase and the article number (e.g. IAN) for all inquiries.
The product number can be found on the type plate, an engraving, the cover page of your instructions
(bottom left), or the sticker on the back or underside of the device.
In the event of malfunctions or other defects, please first contact our service department below by phone
or email. If your product is found to be defective, you can then send your product with proof of purchase
(till receipt) and a statement describing what the fault involves and when it occurred free of charge to the
service address given.
PLEASE NOTE: You can download this handbook and many more, as well as product videos and
software at www.lidl-service.com.
With this QR code you can gain
immediate access to the Lidl Service
page (www.lidl-service.com) and
you can open your operating
instructions by entering the article
number (IAN) 425898.

18 GB
zService
How to contact us:
GB
Name: C. M. C. GmbH Holding
Website: www.cmc-creative.de
E-mail: ser[email protected]
Phone: [phone]
Registered office: Germany
IAN 425898_2301
Please note that the following address is not a service address. Please first contact the service point
given above.
Address:
C. M. C. GmbH Holding
Katharina-Loth-Str. 15
66386 St. Ingbert
Germany
Ordering spare parts:
www.ersatzteile.cmc-creative.de

HU 19
zA használt piktogramok táblázata
A termék használata előtt olvassa
el figyelmesen és teljes egészében
a kezelési útmutatót.
~ 50 Hz Váltakozó feszültség 50 Hz
frekvenciával
TUDNIVALÓ: Ez a szimbólum
a termékkel és használatával
kapcsolatos további információkra
és magyarázatokra utal.
Vigyázat! Lehetséges veszélyek!
Vigyázat! Áramütés veszélye! Vigyázat! Robbanásveszély!
Az így megjelölt készülékeket a
törvény értelmében a nem szelektált
települési hulladéktól elkülönítve kell
ártalmatlanítani. Tilos a háztartási
hulladékkal együtt ártalmatlanítani.
IP20
IP20 védettségi osztály: A készülék
háza által nyújtott védelem feszültség
alatt álló vagy a készülék belsejében
lévő, mozgó alkatrészek ujjal történő
megérintése ellen.
Ilyen savas ólomakkumulátorhoz
alkalmas: 8 Ah – 250 Ah Ne dobja az elektromos készülékeket a háztartási szemét közé!
Csak zárt, szellőztetett terekben
történő alkalmazásra!
Környezetbarát módon ártalmatlanítsa
a csomagolást és a készüléket!
A használt piktogramok táblázata.......................................................................Oldal 19
Bevezetés.................................................................................................................Oldal 20
Rendeltetésszerű használat ........................................................................................Oldal 20
A csomag tartalma ...................................................................................................Oldal 20
Az alkatrészek leírása ...............................................................................................Oldal 21
Műszaki adatok........................................................................................................Oldal 21
Biztonsági tudnivalók.............................................................................................Oldal 21
Kezelés.....................................................................................................................Oldal 25
Terméktulajdonságok.................................................................................................Oldal 25
Töltési módokban történő használat után .....................................................................Oldal 25
Leválasztás töltési módokban történő használat után.....................................................Oldal 26
Töltési mód kiválasztása és a töltési folyamat elindítása.................................................Oldal 26
Indítássegítő funkció használata .................................................................................Oldal 27
Áramgenerátor teszt funkció.......................................................................................Oldal 28
Biztosíték cseréje ......................................................................................................Oldal 29
Karbantartás és ápolás..........................................................................................Oldal 29
Környezetvédelemmel és ártalmatlanítással kapcsolatos tudnivalók ..............Oldal 29
Eredeti EU-Megfelelőségi Nyilatkozat...................................................................Oldal 30
Garanciával és szervizeléssel kapcsolatos tudnivalók .......................................Oldal 31
Garanciális feltételek.................................................................................................Oldal 31
Jótállási idő és törvényben előírt kellékszavatossági igények ..........................................Oldal 31
A garancia terjedelme...............................................................................................Oldal 31
Garanciális eset kezelése ..........................................................................................Oldal 32
Szerviz .....................................................................................................................Oldal 32
Hu jótállási tájékoztató..........................................................................................Oldal 34

20 HU
Csomagolóanyag – hullámpapír Alkalmas személygépkocsikhoz
Alkalmas motorkerékpárokhoz Alkalmas 6 V-os
akkumulátorok töltéséhez
Alkalmas 12 V-os
akkumulátorok töltéséhez Újrahasznosítható anyagokból készült
Akkumulátortöltő indítófunkcióval ULG 17 A1
zBevezetés
Gratulálunk! Vállalatunk kiváló minőségű terméke mellett döntött. A termékkel még az első
üzembe helyezés előtt ismerkedjen meg. Ehhez figyelmesen olvassa el a következő eredeti
használatai útmutatót és a biztonsági tudnivalókat. A termék üzembe helyezését csak
oktatásban részesített személy végezheti.
zRendeltetésszerű használat
Az Ultimate Speed ULG 17 A1 egy gépjármű-akkumulátortöltő készülék impulzusos fenntartó töltéssel
(chip szoftver), amely a következő elektrolitoldatos 6V-os vagy 12V-os ólomakkumulátorok (telepek),
AGM-akkumulátorok, savas ólomakkumulátorok, mélyciklusú (pl. hajóakkumulátorok) vagy zselés akku-
mulátorok töltésére és töltöttségének fenntartására szolgál:
 12 V / 6 V és 8–250 Ah kapacitású személygépkocsi és motorkerékpár akkumulátor
Ezen kívül a készülékkel regenerálhatja a lemerült akkumulátorokat (akkumulátortípustól függően).
Az akkumulátortöltő szikraképződés vagy túlmelegedés elleni védőáramkörrel rendelkezik. Őrizze meg
gondosan ezt az útmutatót. Ha továbbadja a terméket egy harmadik fél számára, mellékelje hozzá az
összes dokumentumot. Minden, a rendeltetésszerű használattól eltérő alkalmazás tilos, és adott esetben
veszélyes lehet. A garancia nem vonatkozik az útmutató be nem tartásából vagy a nem rendeltetésszerű
használatból eredő károkra, és a gyártó céget sem terheli felelősség ilyen esetben. A készülék ipari
használatra nem alkalmas. Ipari használat esetén a garancia érvényét veszti.
ÚTMUTATÁS: Az akkumulátortöltő nem használható beépített akkumulátorral rendelkező elektro-
mos járművek töltésére.
ÚTMUTATÁS: 6 V-os akkumulátorok bikázása nem lehetséges.
zA csomag tartalma
ÚTMUTATÁS: A kicsomagolás után haladéktalanul ellenőrizze a szállítási terjedelmet, valamint
a készülék valamennyi részét, hogy nincsenek-e megsérülve. Hibás készüléket vagy alkatrészeket ne
helyezzen üzembe.
1 db Ultimate Speed ULG 17 A1 gépjármű-akkumulátortöltő készülék
2 db gyorsérintkezős csatlakozókapoccsal (1 piros, 1 fekete)
1 db eredeti használati útmutató