Ultra Start 500 Series User manual

500/550 SERIES
REV.2014.7.21
ADVANCED VEHICLE SECURITY SYSTEM
OWNER'S GUIDE
TM
FCC ID NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2.This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate
this devise.
www.ultrastarters.com

PAGE 2
U500/U550
OWNER'S MANUAL
TABLE OF CONTENTS
Limited Lifetime Warranty................................................................Page 3
Quick View Operations (2way)........................................................Pages 4-5
Quick View Operations (1way)........................................................Pages 6-7
System Operation (Basic)................................................................Page 8
Lock/Arm Alarm Unlock/ Disarm Alarm Driver’s Priority Unlock
Trunk Release Silent Lock/Unlock
System Operation (Optional)...........................................................Pages 9
AUX-1 AUX-2 Panic Mode
AUX-3 Car Finder Mode
System Operation (Remote Transmitter).......................................Page 10
Vibration Mode Temporary Shock Bypass
Service / Valet Mode.........................................................................Page 11
Activate Service Mode Deactivate Service Mode
Transmitter Learning........................................................................Page 12
Dual Car Operation...........................................................................Page 12
Clock Adjustment (2way).................................................................Page 13
Setting the Time of Day
LCD Icons.........................................................................................Pages 14-15
Icon Description
LCD Alarm Pager..............................................................................Pages 16
Remote Programmable Features....................................................Pages 17-18
User Programmable Features
Battery Replacement........................................................................Pages 19
Contact..............................................................................................Page 20
Support email web address
PAGE 3
OWNER'S MANUAL
LIMITED LIFETIME WARRANTY
Applicated Security Technologies, Inc. ("AST") promises to the original purchaser to repair or replace
with a comparable reconditioned model any AST control module ("module") excluding without
limitation any other accessories, including but not limited to the antenna, remote, siren and wiring
harness, proves to be defective in workmanship or material under reasonable use during the lifetime
of the vehicle it was originally installed, provided the following conditions have been met: the module
was professionally installed and serviced by an authorized AST dealer; the unit will be professionally
reinstalled in the vehicle in which it was originally installed by an authorized AST dealer; the warranty
information card was sent to AST within 10 days of the original installation date. Any warranty returns
include a warranty return authorization number issued by AST, original bill or sale and be pre-paid
shipped directly to AST. After an initial period of 2 years from the date of installation, AST reserves
the right, at its sole discretion, to charge a warranty processing fee of $30.00 USD. AST does not
cover the cost for return freight on warranty items, this cost is the sole responsibility of the purchaser.
All components included with the original packaged unit other than the module, including but not
limited to the siren, antenna and the remote transmitters, carry a one-year warranty from the date of
purchase of the same. Any warranty returns on components must include a warranty return
authorization number issued by AST, original bill or sale and be pre-paid shipped directly to AST. This
warranty is non-transferable and is automatically void if: the original purchaser has not completed the
warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the
card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified
or used in a manner contrary to its intended purpose; the unit has been damaged by accident,
unreasonable use, neglect, improper service, installation or other causes not arising out of defects in
materials or construction. The warranty does not cover damage to the unit caused by installation or
removal of the unit. AST, at its sole discretion, will determine what constitutes excessive damage and
may refuse the return of any unit with excessive damage, including, but not limited to, overloading,
moisture and physical damage.
To the maximum extent allowed by law, any and all warranties are excluded by the manufacturer and
each entity participating in the stream of commerce therewith. This exclusion includes but is not
limited to, the exclusion of any and all warranty of merchantability and/or any and all warranty of
fitness for a particular purpose and/or any and all warranty of non-infringement or patents, in the
United States of America and/or abroad. Neither the manufacturer or any entities connected therewith
shall be responsible or liable for any damages whatsoever, including but not limited to, any
consequential damages, incidental damages, damages for loss of time, loss of earnings, commercial
loss, loss of economic opportunity and the like. Notwithstanding the above, manufacturer does offer a
limited warranty to replace or repair the control module as describe above.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or
limitation on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights, and you may also have other
rights, which vary State to State.
U500/U550

PAGE 2
U500/U550
OWNER'S MANUAL
TABLE OF CONTENTS
Limited Lifetime Warranty................................................................Page 3
Quick View Operations (2way)........................................................Pages 4-5
Quick View Operations (1way)........................................................Pages 6-7
System Operation (Basic)................................................................Page 8
Lock/Arm Alarm Unlock/ Disarm Alarm Driver’s Priority Unlock
Trunk Release Silent Lock/Unlock
System Operation (Optional)...........................................................Pages 9
AUX-1 AUX-2 Panic Mode
AUX-3 Car Finder Mode
System Operation (Remote Transmitter).......................................Page 10
Vibration Mode Temporary Shock Bypass
Service / Valet Mode.........................................................................Page 11
Activate Service Mode Deactivate Service Mode
Transmitter Learning........................................................................Page 12
Dual Car Operation...........................................................................Page 12
Clock Adjustment (2way).................................................................Page 13
Setting the Time of Day
LCD Icons.........................................................................................Pages 14-15
Icon Description
LCD Alarm Pager..............................................................................Pages 16
Remote Programmable Features....................................................Pages 17-18
User Programmable Features
Battery Replacement........................................................................Pages 19
Contact..............................................................................................Page 20
Support email web address
PAGE 3
OWNER'S MANUAL
LIMITED LIFETIME WARRANTY
Applicated Security Technologies, Inc. ("AST") promises to the original purchaser to repair or replace
with a comparable reconditioned model any AST control module ("module") excluding without
limitation any other accessories, including but not limited to the antenna, remote, siren and wiring
harness, proves to be defective in workmanship or material under reasonable use during the lifetime
of the vehicle it was originally installed, provided the following conditions have been met: the module
was professionally installed and serviced by an authorized AST dealer; the unit will be professionally
reinstalled in the vehicle in which it was originally installed by an authorized AST dealer; the warranty
information card was sent to AST within 10 days of the original installation date. Any warranty returns
include a warranty return authorization number issued by AST, original bill or sale and be pre-paid
shipped directly to AST. After an initial period of 2 years from the date of installation, AST reserves
the right, at its sole discretion, to charge a warranty processing fee of $30.00 USD. AST does not
cover the cost for return freight on warranty items, this cost is the sole responsibility of the purchaser.
All components included with the original packaged unit other than the module, including but not
limited to the siren, antenna and the remote transmitters, carry a one-year warranty from the date of
purchase of the same. Any warranty returns on components must include a warranty return
authorization number issued by AST, original bill or sale and be pre-paid shipped directly to AST. This
warranty is non-transferable and is automatically void if: the original purchaser has not completed the
warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the
card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified
or used in a manner contrary to its intended purpose; the unit has been damaged by accident,
unreasonable use, neglect, improper service, installation or other causes not arising out of defects in
materials or construction. The warranty does not cover damage to the unit caused by installation or
removal of the unit. AST, at its sole discretion, will determine what constitutes excessive damage and
may refuse the return of any unit with excessive damage, including, but not limited to, overloading,
moisture and physical damage.
To the maximum extent allowed by law, any and all warranties are excluded by the manufacturer and
each entity participating in the stream of commerce therewith. This exclusion includes but is not
limited to, the exclusion of any and all warranty of merchantability and/or any and all warranty of
fitness for a particular purpose and/or any and all warranty of non-infringement or patents, in the
United States of America and/or abroad. Neither the manufacturer or any entities connected therewith
shall be responsible or liable for any damages whatsoever, including but not limited to, any
consequential damages, incidental damages, damages for loss of time, loss of earnings, commercial
loss, loss of economic opportunity and the like. Notwithstanding the above, manufacturer does offer a
limited warranty to replace or repair the control module as describe above.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or
limitation on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights, and you may also have other
rights, which vary State to State.
U500/U550

BUTTON BUTTON CHIRP/ SYSTEM FUNCTION
ICON DURATION FLASH
PAGE 4
OWNER'S MANUAL
QUICK VIEW (2WAY REMOTE)
1 SECOND
1 SECOND
1
0
ARM ALARM / LOCK DOORS
STATUS CHECK
3 SECONDS
3 SECONDS
1
0
ACTIVATE PANIC MODE
ENTER PROGRAM MODE
1 SECOND 2DISARM ALARM / UNLOCK DOORS
1 SECOND - 1 SECOND 3 DRIVER’S DOOR PRIORITY
(OPTIONAL / PROGRAMMABLE)
3 SECONDS 1 AUX 1 OUTPUT**
PRESS TOGETHER
FOR 1 SECOND
FLASH
ONLY SILENT LOCK/ UNLOCK
PRESS AND HOLD FOR
3 SECONDS 2 ACTIVATES TRUNK RELEASE**
#
+
U500/U550
BUTTON BUTTON CHIRP/ SYSTEM FUNCTION
ICON DURATION FLASH
PAGE 5
OWNER'S MANUAL
QUICK VIEW (2WAY REMOTE)
PRESS TOGETHER
FOR 3 SECONDS
PRESS TOGETHER
FOR 3 SECONDS
TUNE ENTER CLOCK ADJUST MODE
FOR REMOTE
PRESS TOGETHER
FOR 3 SECONDS 1AUX 3 OUTPUT**
(DEALER OPTION)
PRESS TOGETHER
FOR 3 SECONDS NONE REMOTE VIBRATION MODE
ON / OFF
+
+
+
+
5 CAR FINDER (DEFAULT)
1 AUX 2 (DEALER OPTION)**
#
#
PRESS AND RELEASE
LOCK THEN PRESS AND
RELEASE TRUNK
1
ARMS / LOCKS AND TURNS OFF
SHOCK SENSOR
(FOR 1 ARM CYCLE ONLY)
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
U500/U550

BUTTON BUTTON CHIRP/ SYSTEM FUNCTION
ICON DURATION FLASH
PAGE 4
OWNER'S MANUAL
QUICK VIEW (2WAY REMOTE)
1 SECOND
1 SECOND
1
0
ARM ALARM / LOCK DOORS
STATUS CHECK
3 SECONDS
3 SECONDS
1
0
ACTIVATE PANIC MODE
ENTER PROGRAM MODE
1 SECOND 2DISARM ALARM / UNLOCK DOORS
1 SECOND - 1 SECOND 3 DRIVER’S DOOR PRIORITY
(OPTIONAL / PROGRAMMABLE)
3 SECONDS 1 AUX 1 OUTPUT**
PRESS TOGETHER
FOR 1 SECOND
FLASH
ONLY SILENT LOCK/ UNLOCK
PRESS AND HOLD FOR
3 SECONDS 2 ACTIVATES TRUNK RELEASE**
#
+
U500/U550
BUTTON BUTTON CHIRP/ SYSTEM FUNCTION
ICON DURATION FLASH
PAGE 5
OWNER'S MANUAL
QUICK VIEW (2WAY REMOTE)
PRESS TOGETHER
FOR 3 SECONDS
PRESS TOGETHER
FOR 3 SECONDS
TUNE ENTER CLOCK ADJUST MODE
FOR REMOTE
PRESS TOGETHER
FOR 3 SECONDS 1AUX 3 OUTPUT**
(DEALER OPTION)
PRESS TOGETHER
FOR 3 SECONDS NONE REMOTE VIBRATION MODE
ON / OFF
+
+
+
+
5 CAR FINDER (DEFAULT)
1 AUX 2 (DEALER OPTION)**
#
#
PRESS AND RELEASE
LOCK THEN PRESS AND
RELEASE TRUNK
1
ARMS / LOCKS AND TURNS OFF
SHOCK SENSOR
(FOR 1 ARM CYCLE ONLY)
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
U500/U550

PAGE 6
OWNER'S MANUAL
QUICK VIEW (1WAY REMOTE)
1 SECOND 1 LOCK / ARM ALARM
3 SECONDS 1 ACTIVATE PANIC
PRESS THEN
RELEASE THEN
PRESS & HOLD
1ACTIVATE CONSTANT LOCK
OUTPUT **
LOCK
BUTTON PRESS CHIRP /
FLASH SYSTEM FUNCTION
BUTTON
1 SECOND 2 UNLOCK / DISARM
1 SECOND
WHILE ALARM IS
TRIGGERED
NONE TURNS OFF SIREN BUT ALARM IS
STILL ARMED
1 SECOND 3
UNLOCK / DISARM
ALARM EVENT IN MEMORY
see alarm event memory chart
UNLOCK
HOLD FOR 3 SECONDS 1 ACTIVATES AUX OUTPUT**
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
PRESS AND HOLD
FOR 3 SECONDS ON ACTIVATES TRUNK RELEASE**
+
NO SIREN CHIRPS - ACTS AS A TOGGLE - IF ARMED WILL DISARM, IF DISARMED WILL ARM
+
#
#
PRESS TOGETHER
FOR 3 SECONDS
5 CAR FINDER (DEFAULT)
1
PRESS TOGETHER
FOR 1 SECOND
FLASH
ONLY SILENT LOCK/ UNLOCK
U500/U550
PAGE 7
OWNER'S MANUAL
QUICK VIEW (1WAY REMOTE)
PRESS AND RELEASE
LOCK THEN PRESS AND
RELEASE TRUNK
1
ARMS / LOCKS AND TURNS OFF
SHOCK SENSOR
(FOR 1 ARM CYCLE ONLY)
1 SECOND - 1 SECOND 1 LOCK / ARM ALARM
1 SECOND - 3 SECONDS 1 ACTIVATE PANIC ALARM
BUTTON PRESS CHIRP /
FLASH SYSTEM FUNCTION
BUTTON
1 SECOND - 1 SECOND 2UNLOCK / DISARM
1 SECOND - 1 SECOND
WHILE ALARM IS
TRIGGERED
NONE TURNS OFF SIREN BUT ALARM IS
STILL ARMED
1 SECOND - 1 SECOND 3
UNLOCK / DISARM
ALARM EVENT IN MEMORY
see alarm event memory chart
1 SECOND - 3 SECONDS 1 ACTIVATES AUX 1 OUTPUT
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
SECOND CAR OPERATION/ PADLOCK. SEE TRANSMITTER PROGRAMMING
FOR INFORMATION ON PROGRAMMING THIS FEATURE.
1 SECOND - 3 SECONDS 1ACTIVATES TRUNK RELEASE
OUTPUT
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
#
#
#
#
#
PRESS TOGETHER
FOR 3 SECONDS 1AUX 3 OUTPUT**
(DEALER OPTION)
+
#
U500/U550
AUX 2 (DEALER OPTION)**

PAGE 6
OWNER'S MANUAL
QUICK VIEW (1WAY REMOTE)
1 SECOND 1 LOCK / ARM ALARM
3 SECONDS 1 ACTIVATE PANIC
PRESS THEN
RELEASE THEN
PRESS & HOLD
1ACTIVATE CONSTANT LOCK
OUTPUT **
LOCK
BUTTON PRESS CHIRP /
FLASH SYSTEM FUNCTION
BUTTON
1 SECOND 2 UNLOCK / DISARM
1 SECOND
WHILE ALARM IS
TRIGGERED
NONE TURNS OFF SIREN BUT ALARM IS
STILL ARMED
1 SECOND 3
UNLOCK / DISARM
ALARM EVENT IN MEMORY
see alarm event memory chart
UNLOCK
HOLD FOR 3 SECONDS 1 ACTIVATES AUX OUTPUT**
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
PRESS AND HOLD
FOR 3 SECONDS ON ACTIVATES TRUNK RELEASE**
+
NO SIREN CHIRPS - ACTS AS A TOGGLE - IF ARMED WILL DISARM, IF DISARMED WILL ARM
+
#
#
PRESS TOGETHER
FOR 3 SECONDS
5 CAR FINDER (DEFAULT)
1
PRESS TOGETHER
FOR 1 SECOND
FLASH
ONLY SILENT LOCK/ UNLOCK
U500/U550
PAGE 7
OWNER'S MANUAL
QUICK VIEW (1WAY REMOTE)
PRESS AND RELEASE
LOCK THEN PRESS AND
RELEASE TRUNK
1
ARMS / LOCKS AND TURNS OFF
SHOCK SENSOR
(FOR 1 ARM CYCLE ONLY)
1 SECOND - 1 SECOND 1 LOCK / ARM ALARM
1 SECOND - 3 SECONDS 1 ACTIVATE PANIC ALARM
BUTTON PRESS CHIRP /
FLASH SYSTEM FUNCTION
BUTTON
1 SECOND - 1 SECOND 2UNLOCK / DISARM
1 SECOND - 1 SECOND
WHILE ALARM IS
TRIGGERED
NONE TURNS OFF SIREN BUT ALARM IS
STILL ARMED
1 SECOND - 1 SECOND 3
UNLOCK / DISARM
ALARM EVENT IN MEMORY
see alarm event memory chart
1 SECOND - 3 SECONDS 1 ACTIVATES AUX 1 OUTPUT
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
SECOND CAR OPERATION/ PADLOCK. SEE TRANSMITTER PROGRAMMING
FOR INFORMATION ON PROGRAMMING THIS FEATURE.
1 SECOND - 3 SECONDS 1ACTIVATES TRUNK RELEASE
OUTPUT
** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS
#
#
#
#
#
PRESS TOGETHER
FOR 3 SECONDS 1AUX 3 OUTPUT**
(DEALER OPTION)
+
#
U500/U550
AUX 2 (DEALER OPTION)**

PAGE 8
OWNER'S MANUAL
SYSTEM OPERATIONS
LOCK/ ARM ALARM
Press and release the Lock Button to lock the vehicle’s doors (if door locks are connected).
The park lights will flash once and the siren/horn will honk/chirp once. The LED on the antenna
will begin to flash (Programmable). The system will arm then monitor the vehicle’s doors, hood
and shock sensor. If any zone is violated the alarm will activate. The 2way remote will display
the large Lock icon when locked.(Some options will require additional parts and/or labour).
UNLOCK/ DISARM ALARM
Press and release the Unlock Button to unlock the vehicle’s doors (if door locks are connected).
The park lights will flash twice and the siren/horn will honk/chirp twice. The LED on the antenna
will stop flashing. If an alarm model was installed the system will disarm. If the alarm was
triggered pressing Unlock once will turn off the siren, pressing Unlock a second time will unlock
and disarm the alarm. The 2way remote will display the large Unlock icon when unlocked.(Some
options will require additional parts and/or labour).
DRIVER’S PRIORITY UNLOCK
When this option is installed and programmed, pressing the Unlock Button once will unlock the
driver’s door. Pressing the Unlock Button a second time will unlock the rest of the vehicle’s
doors. The 2way remote will display the large Unlock icon when this feature is activated.(Some
options will require additional parts and/or labour).
TRUNK RELEASE
Press and hold the Trunk Button for 3 to 5 seconds to activate the trunk release. When
activated the park lights will flash twice and the siren/horn will honk/chirp twice, the doors will
unlock and the trunk will open. The 2way remote will display the large Unlock icon and the Trunk
icon when activated.(Some options will require additional parts and/or labour).
SILENT LOCK/UNLOCK
If you wish to Lock/ Arm or Unlock/ Disarm your vehicle without siren chirps or horn honks on
specific occasions, you can do so by pressing the Lock and Unlock Buttons at the same time for
2 seconds. The system will toggle between lock and unlock without any audible confirmation.
U500/U550
PAGE 9
OWNER'S MANUAL
SYSTEM OPERATIONS
AUXILIARY 1 OUTPUT
The auxiliary outputs can be used to control options such as power windows, sunroofs, power
lift gates, etc. Press and hold the Start Buttons for 3 to 5 seconds to activate the auxiliary output.
When activated the park lights will flash twice, the siren/horn will honk/chirp twice, the doors will
unlock then the auxiliary will activate. The 2-way remote will display A1 when activated.(Some
options will require additional parts and/or labour).
AUXILIARY 2 OUTPUT
The auxiliary outputs can be used to control options such as power windows, sunroofs, power
lift gates, etc. Press and hold the Trunk and Start Buttons for 3 to 5 seconds to activate the
auxiliary output. When activated the park lights will flash twice, the siren/horn will honk/chirp
twice, the doors will unlock then the auxiliary will activate. The 2-way remote will display A2
when activated.(Some options will require additional parts and/or labour).
PANIC MODE
Panic Mode is a personal protection feature that will draw attention to your vehicle. To activate
the Panic Mode feature, press and hold the Lock Button for 3-5 seconds. Panic Mode will flash
the park lights and activate the siren. The lights and siren will stay active for 60 seconds then
turn off. To disable panic mode press and release Lock or Unlock on the remote. The 2-way
remote will beep and flash from green to red when in panic mode.
AUXILIARY 3 OUTPUT
The auxiliary outputs can be used to control options such as power windows, sunroofs, power
lift gates, etc. Press and hold the Lock and Start Buttons for 3 to 5 seconds to activate the
auxiliary output. When activated the park lights will flash twice, the siren/horn will honk/chirp
twice, the doors will unlock then the auxiliary will activate. The 2-way remote will display A3
when activated.(Some options will require additional parts and/or labour).
CAR FINDER
Car finder mode can be used to locate your vehicle in a crowded parking lot. Press and hold the
Start and Trunk Buttons together for 3 seconds. The park lights will flash five times and the
siren/horn will chirp/honk five times. (Programmable Option)
U500/U550

PAGE 8
OWNER'S MANUAL
SYSTEM OPERATIONS
LOCK/ ARM ALARM
Press and release the Lock Button to lock the vehicle’s doors (if door locks are connected).
The park lights will flash once and the siren/horn will honk/chirp once. The LED on the antenna
will begin to flash (Programmable). The system will arm then monitor the vehicle’s doors, hood
and shock sensor. If any zone is violated the alarm will activate. The 2way remote will display
the large Lock icon when locked.(Some options will require additional parts and/or labour).
UNLOCK/ DISARM ALARM
Press and release the Unlock Button to unlock the vehicle’s doors (if door locks are connected).
The park lights will flash twice and the siren/horn will honk/chirp twice. The LED on the antenna
will stop flashing. If an alarm model was installed the system will disarm. If the alarm was
triggered pressing Unlock once will turn off the siren, pressing Unlock a second time will unlock
and disarm the alarm. The 2way remote will display the large Unlock icon when unlocked.(Some
options will require additional parts and/or labour).
DRIVER’S PRIORITY UNLOCK
When this option is installed and programmed, pressing the Unlock Button once will unlock the
driver’s door. Pressing the Unlock Button a second time will unlock the rest of the vehicle’s
doors. The 2way remote will display the large Unlock icon when this feature is activated.(Some
options will require additional parts and/or labour).
TRUNK RELEASE
Press and hold the Trunk Button for 3 to 5 seconds to activate the trunk release. When
activated the park lights will flash twice and the siren/horn will honk/chirp twice, the doors will
unlock and the trunk will open. The 2way remote will display the large Unlock icon and the Trunk
icon when activated.(Some options will require additional parts and/or labour).
SILENT LOCK/UNLOCK
If you wish to Lock/ Arm or Unlock/ Disarm your vehicle without siren chirps or horn honks on
specific occasions, you can do so by pressing the Lock and Unlock Buttons at the same time for
2 seconds. The system will toggle between lock and unlock without any audible confirmation.
U500/U550
PAGE 9
OWNER'S MANUAL
SYSTEM OPERATIONS
AUXILIARY 1 OUTPUT
The auxiliary outputs can be used to control options such as power windows, sunroofs, power
lift gates, etc. Press and hold the Start Buttons for 3 to 5 seconds to activate the auxiliary output.
When activated the park lights will flash twice, the siren/horn will honk/chirp twice, the doors will
unlock then the auxiliary will activate. The 2-way remote will display A1 when activated.(Some
options will require additional parts and/or labour).
AUXILIARY 2 OUTPUT
The auxiliary outputs can be used to control options such as power windows, sunroofs, power
lift gates, etc. Press and hold the Trunk and Start Buttons for 3 to 5 seconds to activate the
auxiliary output. When activated the park lights will flash twice, the siren/horn will honk/chirp
twice, the doors will unlock then the auxiliary will activate. The 2-way remote will display A2
when activated.(Some options will require additional parts and/or labour).
PANIC MODE
Panic Mode is a personal protection feature that will draw attention to your vehicle. To activate
the Panic Mode feature, press and hold the Lock Button for 3-5 seconds. Panic Mode will flash
the park lights and activate the siren. The lights and siren will stay active for 60 seconds then
turn off. To disable panic mode press and release Lock or Unlock on the remote. The 2-way
remote will beep and flash from green to red when in panic mode.
AUXILIARY 3 OUTPUT
The auxiliary outputs can be used to control options such as power windows, sunroofs, power
lift gates, etc. Press and hold the Lock and Start Buttons for 3 to 5 seconds to activate the
auxiliary output. When activated the park lights will flash twice, the siren/horn will honk/chirp
twice, the doors will unlock then the auxiliary will activate. The 2-way remote will display A3
when activated.(Some options will require additional parts and/or labour).
CAR FINDER
Car finder mode can be used to locate your vehicle in a crowded parking lot. Press and hold the
Start and Trunk Buttons together for 3 seconds. The park lights will flash five times and the
siren/horn will chirp/honk five times. (Programmable Option)
U500/U550

PAGE 10
OWNER'S MANUAL
SYSTEM OPERATIONS
VIBRATION MODE (2WAY REMOTE)
The 2way remote transmitter can be programmed not to beep and to vibrate only when a
command is completed. To place the system into Vibration Mode press and hold the Start and
# Buttons for 3 seconds. The remote will vibrate to confirm Vibration Mode. To exit Vibration
Mode press and hold the Start and # Buttons for 3 seconds. The remote will beep to confirm
that audible confirmation is turned back on.
TEMPORARY SHOCK BYPASS
If the vehicle is being parked in an area with a lot of vibration i.e. the airport or a construction
site, the shock sensor can be temporarily turned off to prevent false alarms. When Locking/
Arming the alarm press and release the Trunk Button within 3 seconds of pressing Lock/Arm
Button.
This feature requires that the user must be fully aware of the operation of this feature. If the
system goes into full alarm the remote will no longer function until the Anti Carjack Feature is
disabled.
Type-1 - The timer will start if the door is opened or if the # button is held for 3 seconds while
the ignition is on.
Type-2 - The timer will start if the door is opened or if the # button is held for 3 seconds while
the ignition is on. The timer will also start every time the ignition is turned on.
ANTI CARJACK ALERT
When programmed the Anti Carjack timer is triggered when a door is opened or the key is
pressed on the remote while the ignition is on. Type 2 Carjack Mode will trigger the timer with
the door and trunk button as well as each time the ignition is turned on.
If Anti Carjack is triggered, there will be no indication in the first 20 seconds.
After 20 seconds the LED will begin to flash rapidly to indicate that the Carjack feature is
active. After an additional 20 seconds the siren will then start to chirp each second for an
additional 20 seconds.
The alarm will now activate, the ignition will interrupt, parking lights will flash, and the siren will
alert indicating trouble. The lights and siren will pause momentarily between each one minute
cycle, and repeat until disarmed.
ACTIVATING ANTI CARJACK MODE (International Model Only)
U500/U550
PAGE 11
OWNER'S MANUAL
SYSTEM OPERATIONS
ANTI CARJACK DISARM
To disarm the Anti Carjack Timer, Press and release the valet button. Also Turn the ignition key
off before opening the door to avoid triggering the Anti Carjack Feature.
To disarm the Anti Carjack alert process during the lights and siren cycles, turn the car off then
on, then press and hold the valet button for 5 seconds.
SERVICE/VALET MODE
This feature will disable the remote start and security features of the system. When in Service/
Valet Mode the Lock, Unlock, and Trunk features will still work. The system MUST be put into
Service/ Valet Mode whenever any work is to be done on the vehicle, or if parked in any
enclosed/ partially enclosed area. This procedure can also be used to disarm the alarm if the
remote is lost or damaged.
ENTERING SERVICE MODE
1- Turn the key to the “ON” position.
2- Press and hold the Programming Button located on the antenna (mounted on windshield) for
8 seconds* or until the horn/siren honks/chirps 5 times.
*If programmed for Secure Valet hold Program Button for 15 seconds rather than 8 seconds.
The system is now in Service/ Valet Mode. (The 2 way remote will display Valet and Zzz Icon.)
To confirm this, the LED on the antenna will turn on solid, if a start is attempted you will get a
VALET (3 Flashes) diagnostic code from the park lights on the vehicle..
EXITING SERVICE MODE
1- Turn the key to the “ON” position.
2- Press and hold the Programming Button on the remote starter antenna (mounted on
windshield) for 8 seconds* or until the horn/siren honks/chrirps 2 times.
*If programmed for Secure Valet hold Program Button for 15 seconds rather than 8 seconds.
Service/Valet Mode is now off. (The 2 way remote will turn off Valet and Zzz Icon.)
To confirm this, the LED on the antenna will turn off or flash if the system is in the locked
position. The vehicle can now be remote started and the alarm functions will be active when
U500/U550

PAGE 10
OWNER'S MANUAL
SYSTEM OPERATIONS
VIBRATION MODE (2WAY REMOTE)
The 2way remote transmitter can be programmed not to beep and to vibrate only when a
command is completed. To place the system into Vibration Mode press and hold the Start and
# Buttons for 3 seconds. The remote will vibrate to confirm Vibration Mode. To exit Vibration
Mode press and hold the Start and # Buttons for 3 seconds. The remote will beep to confirm
that audible confirmation is turned back on.
TEMPORARY SHOCK BYPASS
If the vehicle is being parked in an area with a lot of vibration i.e. the airport or a construction
site, the shock sensor can be temporarily turned off to prevent false alarms. When Locking/
Arming the alarm press and release the Trunk Button within 3 seconds of pressing Lock/Arm
Button.
This feature requires that the user must be fully aware of the operation of this feature. If the
system goes into full alarm the remote will no longer function until the Anti Carjack Feature is
disabled.
Type-1 - The timer will start if the door is opened or if the # button is held for 3 seconds while
the ignition is on.
Type-2 - The timer will start if the door is opened or if the # button is held for 3 seconds while
the ignition is on. The timer will also start every time the ignition is turned on.
ANTI CARJACK ALERT
When programmed the Anti Carjack timer is triggered when a door is opened or the key is
pressed on the remote while the ignition is on. Type 2 Carjack Mode will trigger the timer with
the door and trunk button as well as each time the ignition is turned on.
If Anti Carjack is triggered, there will be no indication in the first 20 seconds.
After 20 seconds the LED will begin to flash rapidly to indicate that the Carjack feature is
active. After an additional 20 seconds the siren will then start to chirp each second for an
additional 20 seconds.
The alarm will now activate, the ignition will interrupt, parking lights will flash, and the siren will
alert indicating trouble. The lights and siren will pause momentarily between each one minute
cycle, and repeat until disarmed.
ACTIVATING ANTI CARJACK MODE (International Model Only)
U500/U550
PAGE 11
OWNER'S MANUAL
SYSTEM OPERATIONS
ANTI CARJACK DISARM
To disarm the Anti Carjack Timer, Press and release the valet button. Also Turn the ignition key
off before opening the door to avoid triggering the Anti Carjack Feature.
To disarm the Anti Carjack alert process during the lights and siren cycles, turn the car off then
on, then press and hold the valet button for 5 seconds.
SERVICE/VALET MODE
This feature will disable the remote start and security features of the system. When in Service/
Valet Mode the Lock, Unlock, and Trunk features will still work. The system MUST be put into
Service/ Valet Mode whenever any work is to be done on the vehicle, or if parked in any
enclosed/ partially enclosed area. This procedure can also be used to disarm the alarm if the
remote is lost or damaged.
ENTERING SERVICE MODE
1- Turn the key to the “ON” position.
2- Press and hold the Programming Button located on the antenna (mounted on windshield) for
8 seconds* or until the horn/siren honks/chirps 5 times.
*If programmed for Secure Valet hold Program Button for 15 seconds rather than 8 seconds.
The system is now in Service/ Valet Mode. (The 2 way remote will display Valet and Zzz Icon.)
To confirm this, the LED on the antenna will turn on solid, if a start is attempted you will get a
VALET (3 Flashes) diagnostic code from the park lights on the vehicle..
EXITING SERVICE MODE
1- Turn the key to the “ON” position.
2- Press and hold the Programming Button on the remote starter antenna (mounted on
windshield) for 8 seconds* or until the horn/siren honks/chrirps 2 times.
*If programmed for Secure Valet hold Program Button for 15 seconds rather than 8 seconds.
Service/Valet Mode is now off. (The 2 way remote will turn off Valet and Zzz Icon.)
To confirm this, the LED on the antenna will turn off or flash if the system is in the locked
position. The vehicle can now be remote started and the alarm functions will be active when
U500/U550

PAGE 12
OWNER'S MANUAL
LCD FUNCTIONS
ARM
PM
12:15
PAGER
1
F
PROGRAM
TRANSMITTER LEARNING
The system can lean up to 4 different remote transmitter codes. Each remote to be used MUST
be programmed together during the same sequence. For security, when a new remote is
programmed all previous remotes that are not reprogrammed at this time will be deleted.
1- Cycle the ignition key ON-OFF-ON-OFF-ON.
2- Press and hold the Button on the antenna, the park lights will turn on and the siren/horn
(optional) will chirp/honk once. (Continue Holding antenna Button).
3- After 5 seconds the park lights will turn off and the siren/horn will chirp/honk 5 times to
indicate you have entered Transmitter Learning Mode.
4- Press the Lock Button on each of the transmitters to be programmed. The park lights will flash
and siren/horn will chirp/honk once to indicate successfully learning of each transmitter.
5- Turn the ignition key OFF to exit remote Program mode.
DUAL CAR OPERATION (CAR-1 / CAR-2)
2 WAY REMOTE ONLY
The 2way remote transmitter can be programmed to a second vehicle to
control the alarm and remote starter feature. By default the remote is set to
CAR-1, this is indicated by number 1 on the LCD screen. In CAR-1 the LCD
back light is Green, in CAR-2 mode the back light is red.
The second vehicle must also have the same model 2way starter installed. To
Program the remote in second car mode,
1- Press and hold the # Button until the Program icon appears.
2- Press and release the Lock Button until the number 1 icon turns on.
3- Press the Start Button to change form 1 to 2.
4- Press # to exit.
Now that the remote is set for CAR-2 “2". You can Program it along with the other remote to the
second vehicle. The remote now controls the second vehicle’s functions. To go back to CAR-1
operation follow the steps above. Press the Unlock Button instead of Start Button to change
back to CAR-1 “1".
U500/U550
PAGE 13
OWNER'S MANUAL
LCD FUNCTIONS
Enter Clock Adjustment Mode,
1- Press and Hold the Lock and # Buttons for 3-5 seconds.
2- The remote will play the Program tune.
3- The PROGRAM icon will turn on and the minute portion of the clock will
start to flash.
Clock Adjustment
The clock must be set when the remote battery is removed or replaced. Follow the steps
below to set or adjust the clock.
ARM
PM
12:45
PAGER
1
F
Setting the Minutes
1- Press and release the Unlock Button to decrease the Minutes.
2- Press and release the Start Button to increase the Minutes.
3- To Select the Hour press and release the Lock Button.
3- To exit press and release the # Button.
ARM
PM
12:15
PAGER
1
F
PROGRAM
PROGRAM
Setting the Hour
1- Press and release the Unlock Button to decrease the Hour.
2- Press and release the Start Button to increase the Hour.
3- To Select the Minutes press and release the Lock Button.
3- To exit press and release the # Button.
ARM
PM
1:15
PAGER
1
F
PROGRAM
Exit Clock Adjustment Mode
1- Press and release the # Button.
2- The remote will exit Clock Adjustment Mode.
3- The PROGRAM icon will turn off.
*If no Buttons are pressed for 15 seconds the remote will automatically exit
Clock Adjustment Mode.
ARM
PM
1:15
PAGER
1
F
U500/U550

PAGE 12
OWNER'S MANUAL
LCD FUNCTIONS
ARM
PM
12:15
PAGER
1
F
PROGRAM
TRANSMITTER LEARNING
The system can lean up to 4 different remote transmitter codes. Each remote to be used MUST
be programmed together during the same sequence. For security, when a new remote is
programmed all previous remotes that are not reprogrammed at this time will be deleted.
1- Cycle the ignition key ON-OFF-ON-OFF-ON.
2- Press and hold the Button on the antenna, the park lights will turn on and the siren/horn
(optional) will chirp/honk once. (Continue Holding antenna Button).
3- After 5 seconds the park lights will turn off and the siren/horn will chirp/honk 5 times to
indicate you have entered Transmitter Learning Mode.
4- Press the Lock Button on each of the transmitters to be programmed. The park lights will flash
and siren/horn will chirp/honk once to indicate successfully learning of each transmitter.
5- Turn the ignition key OFF to exit remote Program mode.
DUAL CAR OPERATION (CAR-1 / CAR-2)
2 WAY REMOTE ONLY
The 2way remote transmitter can be programmed to a second vehicle to
control the alarm and remote starter feature. By default the remote is set to
CAR-1, this is indicated by number 1 on the LCD screen. In CAR-1 the LCD
back light is Green, in CAR-2 mode the back light is red.
The second vehicle must also have the same model 2way starter installed. To
Program the remote in second car mode,
1- Press and hold the # Button until the Program icon appears.
2- Press and release the Lock Button until the number 1 icon turns on.
3- Press the Start Button to change form 1 to 2.
4- Press # to exit.
Now that the remote is set for CAR-2 “2". You can Program it along with the other remote to the
second vehicle. The remote now controls the second vehicle’s functions. To go back to CAR-1
operation follow the steps above. Press the Unlock Button instead of Start Button to change
back to CAR-1 “1".
U500/U550
PAGE 13
OWNER'S MANUAL
LCD FUNCTIONS
Enter Clock Adjustment Mode,
1- Press and Hold the Lock and # Buttons for 3-5 seconds.
2- The remote will play the Program tune.
3- The PROGRAM icon will turn on and the minute portion of the clock will
start to flash.
Clock Adjustment
The clock must be set when the remote battery is removed or replaced. Follow the steps
below to set or adjust the clock.
ARM
PM
12:45
PAGER
1
F
Setting the Minutes
1- Press and release the Unlock Button to decrease the Minutes.
2- Press and release the Start Button to increase the Minutes.
3- To Select the Hour press and release the Lock Button.
3- To exit press and release the # Button.
ARM
PM
12:15
PAGER
1
F
PROGRAM
PROGRAM
Setting the Hour
1- Press and release the Unlock Button to decrease the Hour.
2- Press and release the Start Button to increase the Hour.
3- To Select the Minutes press and release the Lock Button.
3- To exit press and release the # Button.
ARM
PM
1:15
PAGER
1
F
PROGRAM
Exit Clock Adjustment Mode
1- Press and release the # Button.
2- The remote will exit Clock Adjustment Mode.
3- The PROGRAM icon will turn off.
*If no Buttons are pressed for 15 seconds the remote will automatically exit
Clock Adjustment Mode.
ARM
PM
1:15
PAGER
1
F
U500/U550

PAGE 14
OWNER'S MANUAL
LCD FUNCTIONS
LCD 2way Remote Transmitter.
The 2way remote transmitter will give you audible and visual
feedback of the preformed function, Locked, Unlocked,
Trunk, Remote Start etc. The system will also send the
remote a page if the alarm is triggered.
24H
AM
PM
12:45
E
PAGER
O
Signal- Icon is on when in range of the receiver.
Low Temp Mode- Icon is on when the low temp mode feature is set on. (N/A)
Time Status- Displays the time
Valet Mode- This icon is displayed when the Valet Mode is turned on.
Pager- When on this indicates that the remote pager mode is on.
Vibration Mode- Icon is on when remote is set to vibrate.
Battery Status- Indicates the battery level.
Temperature Scale Display* - C or F (N/A)
Reservation Mode* - N/A
Timer Mode*- Icon is on when the timer mode feature is set on. (N/A)
Clock (AM/ PM)- Indicates the AM or PM.
Shock Sensor- Indicates that the shock sensor has triggered the alarm.
24H* - This icon is on if the Timer Start mode has been set on. (N/A)
PROGRAM
ARM
C
24H
AM
PM
12:45
E
PAGER
VALET
TURBO
IDLE
O
1 2
F
TRUNK
HOODSTART
ALARM
OFFON
* Not Available in this model
U500/U550
PAGE 15
OWNER'S MANUAL
LCD FUNCTIONS
PROGRAM
ARM
C
VALET
TURBO
IDLE
1 2
F
TRUNK
HOOD
START
OFFON
Idle Mode*- This icon will turn on when the system is in Idle Mode. (N/A)
1 2- Indicates if the remote is in car 1 or car 2 operation.
C F*- These icons are used to set the temperature to Celsius or Fahrenheit. (N/A)
Alarm- This will turn on and flash when the alarm is triggered.
Valet Mode- When this icon is on the system is in Valet Mode.
Lock Icon- Indicates that the doors are lock/ alarm is armed.
Small Siren Icon- This icon indicates if the siren/ horn is set on or off.
ARM- This icon turns on when the doors are locked/ alarm is armed.
Start*- This Icon turns on when the vehicle is remote started. (N/A)
Timer Mode*- This icon will turn on when the system is in Turbo Mode. (N/A)
Unlock Icon- Indicates that the doors are unlocked/ alarm is disarmed.
Small Hammer Icon- This icon indicates if the shock sensor is set on or off.
Hood- Displayed if the hood is open when remote starting or triggering the alarm.
Program- This icon is on when the remote is in Program mode.
ON OFF- These icons are displayed when changing a setting in Program mode.
Trunk- This icon will turn on when the trunk is opened by the remote.
ALARM
U500/U550

PAGE 14
OWNER'S MANUAL
LCD FUNCTIONS
LCD 2way Remote Transmitter.
The 2way remote transmitter will give you audible and visual
feedback of the preformed function, Locked, Unlocked,
Trunk, Remote Start etc. The system will also send the
remote a page if the alarm is triggered.
24H
AM
PM
12:45
E
PAGER
O
Signal- Icon is on when in range of the receiver.
Low Temp Mode- Icon is on when the low temp mode feature is set on. (N/A)
Time Status- Displays the time
Valet Mode- This icon is displayed when the Valet Mode is turned on.
Pager- When on this indicates that the remote pager mode is on.
Vibration Mode- Icon is on when remote is set to vibrate.
Battery Status- Indicates the battery level.
Temperature Scale Display* - C or F (N/A)
Reservation Mode* - N/A
Timer Mode*- Icon is on when the timer mode feature is set on. (N/A)
Clock (AM/ PM)- Indicates the AM or PM.
Shock Sensor- Indicates that the shock sensor has triggered the alarm.
24H* - This icon is on if the Timer Start mode has been set on. (N/A)
PROGRAM
ARM
C
24H
AM
PM
12:45
E
PAGER
VALET
TURBO
IDLE
O
1 2
F
TRUNK
HOODSTART
ALARM
OFFON
* Not Available in this model
U500/U550
PAGE 15
OWNER'S MANUAL
LCD FUNCTIONS
PROGRAM
ARM
C
VALET
TURBO
IDLE
1 2
F
TRUNK
HOOD
START
OFFON
Idle Mode*- This icon will turn on when the system is in Idle Mode. (N/A)
1 2- Indicates if the remote is in car 1 or car 2 operation.
C F*- These icons are used to set the temperature to Celsius or Fahrenheit. (N/A)
Alarm- This will turn on and flash when the alarm is triggered.
Valet Mode- When this icon is on the system is in Valet Mode.
Lock Icon- Indicates that the doors are lock/ alarm is armed.
Small Siren Icon- This icon indicates if the siren/ horn is set on or off.
ARM- This icon turns on when the doors are locked/ alarm is armed.
Start*- This Icon turns on when the vehicle is remote started. (N/A)
Timer Mode*- This icon will turn on when the system is in Turbo Mode. (N/A)
Unlock Icon- Indicates that the doors are unlocked/ alarm is disarmed.
Small Hammer Icon- This icon indicates if the shock sensor is set on or off.
Hood- Displayed if the hood is open when remote starting or triggering the alarm.
Program- This icon is on when the remote is in Program mode.
ON OFF- These icons are displayed when changing a setting in Program mode.
Trunk- This icon will turn on when the trunk is opened by the remote.
ALARM
U500/U550

ARM
PM
12:45
PAGER
1
F
ALARM
DOOR OPENED
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The Lock icon with toggle from Lock to Unlock
3- The ALARM icon will start flashing.
4- The remote will beep on and off. (Vibrate in Vibration Mode).
5- The back light will switch colors from green to red.
6- The remote will page and flash for 1 minute then stop.
ALARM PAGER
If the alarm is triggered the remote will begin to beep on and off (Vibrate in Vibration Mode)
and the LCD screen with display the alarm trigger. The PAGER icon must be on for the
remote to receive and display alarm triggers.
ARM
PM
12:45
PAGER
1
F
ALARM
SHOCK SENSOR TRIGGERED
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The Shock Sensor (Hammer Striking) icon will turn on.
3- The ALARM icon will start flashing.
4- The remote will beep on and off. (Vibrate in Vibration Mode).
5- The back light will switch colors from green to red.
6- The remote will page and flash for 1 minute then stop.
HOOD OPENED (Not Available in this model)
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The HOOD icon will turn on.
3- The ALARM icon will start flashing.
4- The remote will beep on and off. (Vibrate in Vibration Mode).
5- The back light will switch colors from green to red.
6- The remote will page and flash for 1 minute then stop.
ARM
PM
12:45
PAGER
1
F
HOOD
ALARM
PANIC MODE
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The ALARM icon will start flashing.
3- The remote will beep on and off. (Vibrate in Vibration Mode).
4- The back light will switch colors from green to red.
5- The remote will page and flash for 1 minute then stop.
ARM
PM
12:45
PAGER
1
F
ALARM
PAGE 16
OWNER'S MANUAL
LCD FUNCTIONS
U500/U550
Enter Program Mode,
1- Press and Hold the # Button for 3-5 seconds.
2- The remote will play the Program tune.
3- The PROGRAM icon will turn on and start to flash.
4- Press and release the Lock Button to cycle through the settings.
REMOTE PROGRAMMABLE FEATURES
This feature allows the user to Program certain system features using the remote transmitter.
24H- Turn Cold Start ON or OFF. (Not Available in this model)
1- Press and release the Lock Button to select the 24H icon.
2- Press and release the Unlock Button to turn Timer Start ON.
3- Press and release the Start Button to turn Timer Start OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
12:15
PROGRAM
PAGER- Turn Pager Mode ON or OFF.
1- Press and release the Lock Button to select the PAGER icon.
2- Press and release the Unlock Button to turn the Pager ON.
3- Press and release the Start Button to turn the Pager OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
PAGER
PROGRAM
PM
12:15
PAGER
PROGRAM
VALET- Turn Valet Mode ON or OFF.
1- Press and release the Lock Button to select the VALET icon.
2- Press and release the Unlock Button to turn the Valet ON.
3- Press and release the Start Button to turn the Valet OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
PROGRAM
24H
VALET
PAGE 17
OWNER'S MANUAL
LCD FUNCTIONS
U500/U550

ARM
PM
12:45
PAGER
1
F
ALARM
DOOR OPENED
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The Lock icon with toggle from Lock to Unlock
3- The ALARM icon will start flashing.
4- The remote will beep on and off. (Vibrate in Vibration Mode).
5- The back light will switch colors from green to red.
6- The remote will page and flash for 1 minute then stop.
ALARM PAGER
If the alarm is triggered the remote will begin to beep on and off (Vibrate in Vibration Mode)
and the LCD screen with display the alarm trigger. The PAGER icon must be on for the
remote to receive and display alarm triggers.
ARM
PM
12:45
PAGER
1
F
ALARM
SHOCK SENSOR TRIGGERED
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The Shock Sensor (Hammer Striking) icon will turn on.
3- The ALARM icon will start flashing.
4- The remote will beep on and off. (Vibrate in Vibration Mode).
5- The back light will switch colors from green to red.
6- The remote will page and flash for 1 minute then stop.
HOOD OPENED (Not Available in this model)
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The HOOD icon will turn on.
3- The ALARM icon will start flashing.
4- The remote will beep on and off. (Vibrate in Vibration Mode).
5- The back light will switch colors from green to red.
6- The remote will page and flash for 1 minute then stop.
ARM
PM
12:45
PAGER
1
F
HOOD
ALARM
PANIC MODE
1- The alarm will activate (Siren On and Park Lights Flashing).
2- The ALARM icon will start flashing.
3- The remote will beep on and off. (Vibrate in Vibration Mode).
4- The back light will switch colors from green to red.
5- The remote will page and flash for 1 minute then stop.
ARM
PM
12:45
PAGER
1
F
ALARM
PAGE 16
OWNER'S MANUAL
LCD FUNCTIONS
U500/U550
Enter Program Mode,
1- Press and Hold the # Button for 3-5 seconds.
2- The remote will play the Program tune.
3- The PROGRAM icon will turn on and start to flash.
4- Press and release the Lock Button to cycle through the settings.
REMOTE PROGRAMMABLE FEATURES
This feature allows the user to Program certain system features using the remote transmitter.
24H- Turn Cold Start ON or OFF. (Not Available in this model)
1- Press and release the Lock Button to select the 24H icon.
2- Press and release the Unlock Button to turn Timer Start ON.
3- Press and release the Start Button to turn Timer Start OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
12:15
PROGRAM
PAGER- Turn Pager Mode ON or OFF.
1- Press and release the Lock Button to select the PAGER icon.
2- Press and release the Unlock Button to turn the Pager ON.
3- Press and release the Start Button to turn the Pager OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
PAGER
PROGRAM
PM
12:15
PAGER
PROGRAM
VALET- Turn Valet Mode ON or OFF.
1- Press and release the Lock Button to select the VALET icon.
2- Press and release the Unlock Button to turn the Valet ON.
3- Press and release the Start Button to turn the Valet OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
PROGRAM
24H
VALET
PAGE 17
OWNER'S MANUAL
LCD FUNCTIONS
U500/U550

PAGE 18
OWNER'S MANUAL
LCD FUNCTIONS
1- Select Car 1 or Car 2 Operation.
1- Press and release the Lock Button to select the 1 icon.
2- Press and release the Unlock Button for CAR-1 (Default).
3- Press and release the Start Button for CAR-2.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
1
SIREN- Turn the Siren Chirp ON or OFF.
1- Press and release the Lock Button to select the SIREN icon.
2- Press and release the Unlock Button to turn the Siren ON.
3- Press and release the Start Button to turn the Siren OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
12:15
PROGRAM
Hammer- Turn the Shock Sensor ON or OFF.
1- Press and release the Lock Button to select the SIREN icon.
2- Press and release the Unlock Button to turn the Siren ON.
3- Press and release the Start Button to turn the Siren OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
C- Temperature Scale (Not Available in this model)
1- Press and release the Lock Button to select the C icon.
2- Press and release the Unlock Button to set for Celsius.
3- Press and release the Start Button to set for Fahrenheit.
4- Press and release the # Button to exit or Lock to go back to the first
programmable setting.
PM
1:15
C
PROGRAM
PROGRAM
U500/U550
BATTERY REPLACEMENT
If you notice decreased range while using your remote transmitter, it is possible that your
transmitter’s battery needs to be replaced. To replace your battery follow the steps below.
1-WAY REMOTE TRANSMITTERS
1. Remove the small Phillips screw on the back side of the remote
2. Gently pull the remote transmitter apart.
3. Remove the battery and replace with a new battery. If you are having trouble finding the
proper size of the battery, the model number is printed on the battery case.
4. Replace the back cover of remote transmitter and replace Phillips screw.
2-WAY REMOTE TRANSMITTERS
1. Remove the battery cover by sliding it out from the back of the remote.
2. Remove and replace with a new AAA battery.
3. Replace the cover by sliding it back into it’s case.
INSTALLATION INFORMATION
Date of Installation______________________________________________
Installation Shop________________________________________________
Installation Shop Telephone_______________________________________
Name of Technician______________________________________________
PAGE 19
OWNER'S MANUAL
BATTERY REPLACEMENT
U500/U550

PAGE 18
OWNER'S MANUAL
LCD FUNCTIONS
1- Select Car 1 or Car 2 Operation.
1- Press and release the Lock Button to select the 1 icon.
2- Press and release the Unlock Button for CAR-1 (Default).
3- Press and release the Start Button for CAR-2.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
1
SIREN- Turn the Siren Chirp ON or OFF.
1- Press and release the Lock Button to select the SIREN icon.
2- Press and release the Unlock Button to turn the Siren ON.
3- Press and release the Start Button to turn the Siren OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
12:15
PROGRAM
Hammer- Turn the Shock Sensor ON or OFF.
1- Press and release the Lock Button to select the SIREN icon.
2- Press and release the Unlock Button to turn the Siren ON.
3- Press and release the Start Button to turn the Siren OFF.
4- Press and release the # Button to exit or Lock to continue to the next
programmable setting.
PM
1:15
C- Temperature Scale (Not Available in this model)
1- Press and release the Lock Button to select the C icon.
2- Press and release the Unlock Button to set for Celsius.
3- Press and release the Start Button to set for Fahrenheit.
4- Press and release the # Button to exit or Lock to go back to the first
programmable setting.
PM
1:15
C
PROGRAM
PROGRAM
U500/U550
BATTERY REPLACEMENT
If you notice decreased range while using your remote transmitter, it is possible that your
transmitter’s battery needs to be replaced. To replace your battery follow the steps below.
1-WAY REMOTE TRANSMITTERS
1. Remove the small Phillips screw on the back side of the remote
2. Gently pull the remote transmitter apart.
3. Remove the battery and replace with a new battery. If you are having trouble finding the
proper size of the battery, the model number is printed on the battery case.
4. Replace the back cover of remote transmitter and replace Phillips screw.
2-WAY REMOTE TRANSMITTERS
1. Remove the battery cover by sliding it out from the back of the remote.
2. Remove and replace with a new AAA battery.
3. Replace the cover by sliding it back into it’s case.
INSTALLATION INFORMATION
Date of Installation______________________________________________
Installation Shop________________________________________________
Installation Shop Telephone_______________________________________
Name of Technician______________________________________________
PAGE 19
OWNER'S MANUAL
BATTERY REPLACEMENT
U500/U550

IMPORTANT NOTES
LOCK, UNLOCK, DRIVER'S DOOR PRIORITY UNLOCK, TRUNK RELEASE AND THE
AUXILIARY OUTPUTS ARE OPTIONAL OUTPUTS. ENABLING THESE FEATURES
REQUIRES CUSTOM INSTALLATION & PROGRAMMING. THESE FEATURES MAY NOT BE
COMPATIBLE WITH SOME VEHICLES.
FOR SAFETY REASONS THE TRUNK RELEASE OUTPUT WILL NOT ACTIVATE WHEN THE
IGNITION IS IN THE ON POSITION.
NOTE: PADLOCK AND 2ND CAR OPERATION ARE FEATURES THAT REQUIRE SPECIAL
PROGRAMMING.
SOME FEATURES MAY NOT BE AVAILABLE FOR ALL APPLICATIONS. CONTACT YOUR
DEALER FOR MORE INFORMATION.
technical support: [email protected]
additional product information: www.ultrastarters.com
This manual suits for next models
1
Table of contents
Other Ultra Start Security System manuals