UMBRA RIMORCHI 14083 User manual

ISTRUZIONI DI MONTAGGIO
FITTING INSTRUCTIONS
INSTRUCTIONS DE MONTAGE
MONTAGEANLEITUNG
INSTRUCCIONES DE MONTAJE
ИНСТРУКЦИЯ ПО УСТАНОВКЕ
DIS OSITIVO DI TRAINO TI O
TOWING DIS OSAL TY E
TY E DU DIS OSITIF DE REMORQUAGE
ANHÄNGERVORRICHTUNG TY
DIS OSITIVO DE CAREO TI O
ТЯГОВО-СЦЕПНОЕ УСТРОЙСТВО
14083
ER AUTOVEICOLI
FOR CARS
OUR VÉHICULES AUTOMOBILES
FÜR KRAFTFAHRZEUGE
ARA AUTOVEHICULO
ДЛЯ АВТОМОБИЛЕЙ
FORD MONDEO Berlina 4Pt,
Wa on
2007 =>
(BA7)
CLASSE E TI O DI ATTACCO
CLASS AND HITCH TY E
CLASSE ET TY E DE CROCHET
KLASSE UND BEFESTIGUNGSART
CLASES DE ACO LAMIENTO
КЛАСС И ТИП СОЕДИНЕНИЯ
F
OMOLOGAZIONE
HOMOLOGATION
HOMOLOGATION
ZULASSUNG
A ROBACION
ОМОЛОГАЦИЯ
e3 00 – 7430
(DIR. 94/20/CE)
CARICO VERTICALE MAX
S VALUE
MASSE VERTICALE MAXIMUM
ZUL. STÜTZLAST
CARGA MAX. VERTICAL
МАКСИМАЛЬНАЯ ВЕРTИКАЛЬНАЯ НАГРУЗКА
S = kg 115
VALORE D
D VALUE
VALEUR D
D WERT
VALOR D
ЗНАЧЕНИЕ
CO IA DI SERRAGGIO ER VITI (8.8):
TORQUE SETTINGS FOR NUTS AND BOLTS (8.8):
COU LE DE SERRAGE OUR VIS (8.8):
SCHRAUBENANZUGSMOMENT (8.8):
MOM. DE RESION ARA TORNILLOS Y TUERCAS (8.8):
СПИСОК ДЕТАЛЕЙ (8.8):
14083 04/08/14 v. 1.0 . 1 / 8
UMBRA RIMORCHI
Via C. izzoni 37/39, 06132 erugia - Italy
Tel. [phone]
Fax [phone]
www.umbrarimorchi.it
[email protected]
kN 11,3
M6 = Nm 10 M8 = Nm 25
M10 = Nm 55 M12 = Nm 85
M14 = Nm 135 M16 = Nm 200

SAFETY INSTRUCTIONS
Make sure that the tow bar is suitable for the vehicle before starting the
installation. Verify also that the vehicle's towing disposal quoted on the car
registration is mentioned on the tow bar document. Otherwise ask the proper
office ([email protected]) for explanation or updated documents.
For safety, all work involving tow bar installation must be undertaken by skilled
technicians.
Damaged components must be replaced with manufacturer’s spares parts by
qualified staff.
It is forbidden to make any modification or structural repair to the tow bar.
USE AND MAINTENANCE
The tow ball must be kept clean and lubricated. For added safety, his diameter (50
mm) must be checked at regular intervals. If the tow ball measures less than 49
mm after selected readings across the diameter, the tow ball must be replaced
with a new one.
After 1000 km of towing, check torque settings for nuts and bolts, in accordance
with the table.
CAUTION
The towbar installer must fix at the same level with the ball in a clear position, a plate
with the ball's maximum load for the vehicle on which the tow bar is fitted.
14083 04/08/14 v. 1.0 . 2 / 8

FITTING INSTRUCTIONS
14083
Remove from below the vehicle any protective sealant from the points of contact
between the shell and the tow bar; then paint the uncovered parts with rust preventer.
The holes for the tow bar's fixing are available.
1. Disassemble the rear bumper.
2. Disassemble and eliminate the inner reinforcement's crossbeam.
3. Disassemble the exhaust pipe's rubber support.
4. Lower the rear side of the heat guard cladding.
5. lace components “B” within the spars in correspondence to holes “1” and “3”;
insert screws in position “1” and fix interjecting the wide washers.
6. lace tow beam “A” within the spars in correspondence to holes “2” and “3”; insert
screws and then fix interjecting the wide washers in position “3”.
7. Tighten all bolts and nuts with a tightening torque as shown in the enclosed
layout.
8. Connect the wiring to the socket (usually given apart), following the car booklet's
instructions “use and maintenance” as shown in the enclosed wiring kit layout.
9. FORD MONDEO Wagon: Make a cut on the bumper's lower side as shown in the
enclosed layout.
10. Reassemble the heat guard cladding, the exhaust pipe's rubber support and the
rear bumper.
14083 04/08/14 v. 1.0 . 3 / 8

14083 04/08/14 v. 1.0 . 4 / 8

14083 04/08/14 v. 1.0 . 5 / 8

14083 04/08/14 v. 1.0 . 6 / 8

14083 04/08/14 v. 1.0 . 7 / 8

14083 04/08/14 v. 1.0 . 8 / 8