Unfinished Furniture of Wilmington BD-2038 User manual

ITEM NO.: BD-2038
REVISED OCT 09, 2018
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
WARNING!
Serious or fatal injuries can occur from furniture tip over. Use tip over restraint
(steel band included) to secure this product to the wall.
Description
Item No.
: 8 DRAWER 1 DOOR COTTAGE DRESSER
: BD-2038

ITEM NO.: BD-2038
REVISED OCT 09, 2018
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product
with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: BD-2038
REVISED OCT 09, 2018
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
A
8 DRAWER 1 DOOR DRESSER
1
B
LEG
4
C
CENTER LEG
1
D
SHELF
1

ITEM NO.: BD-2038
REVISED OCT 09, 2018
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Wooden knob
(35 x 35mm)
13
4
Short screw
(M3.5 x 15mm)
8
METAL KNOB
(32 x 28mm)
GOES WITH FINISHED
ITEM ONLY.
13
5
Bracket
4
2
Pan head screw
*Wooden knob: (M4x25mm)
13
6
Steel band
2
Pan head screw
*Metal knob: (M4x22mm)
13
7
Allen key
(M4 x 30mm x 110mm)
1
3
Long screw
(M4 x 35mm)
2
NOTE: WARNING LABEL (INCLUDED)

ITEM NO.: BD-2038
REVISED OCT 09, 2018
Printed in Vietnam
- 5 -
STEP 1
Use the Allen key (7) to loosen the bolts and washers, and then remove three pieces of wood
from bottom of the dresser (A), as shown below.

ITEM NO.: BD-2038
REVISED OCT 09, 2018
Printed in Vietnam
- 6 -
STEP 2
Lift the dresser (A) to attach legs (B) and (C) by screwing them into dresser (A), as shown below.
STEP 3
Attach brackets (5) to the unit as shown below. Place shelf (D) on the brackets and attach with screws (4).
Tighten with a screwdriver.

ITEM NO.: BD-2038
REVISED OCT 09, 2018
Printed in Vietnam
- 7 -
STEP 4
Attach knobs (1) to front of drawers and door with pan head screws (2), as shown below. Tighten with a
screwdriver.
STEP 5
Attach steel bands (6) to the unit with screws (4) as shown below.
(to secure the product to the wall and reduce the risk of tipping over).
Important!
Properly attach steel bands (6) to the wall in an area of drywall or plaster with a wood stud:
Mark the attachment point(s) with a pencil at the appropriate height positioned over the wood stud(s)
in the wall.
Drill 1/8-inch (3mm) diameter hole(s) into the wood stud(s) located in the wall, where you marked
with the pencil.
Properly attach steel bands to the wall with screws (3) and tighten screw(s) firmly into the wall.