Unfinished Furniture of Wilmington CANYON SV-37 User manual

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 1 - THIS ITEM IS PACKED IN TWO CARTONS
Description
Item No.
: CANYON SERVER
: SV - 37
ASSEMBLY INSTRUCTIONS

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 2 - THIS ITEM IS PACKED IN TWO CARTONS
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws, bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your product. Protect the surface of the product with cloth if you are using any product
with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 3 - THIS ITEM IS PACKED IN TWO CARTONS
PART LIST SV –37A
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts.
NO
Description
Qty
Sketch
A
Top
1
PART LIST SV –37B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts.
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
B
Side panel
2
C
Bottom
panel
1
D
Side panel
wine rack
2
E
Top panel
wine rack
1
F
Bottom panel
wine rack
1
G
1 - Center
panel
wine rack
2
H
2 - Center
panel
wine rack
1
K
3- Center
panel
wine rack
2
L
4 - Center
panel
wine rack
2

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 4 - THIS ITEM IS PACKED IN TWO CARTONS
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 35mm)
12
2
Lock washer
(6.5 x11mm)
12
3
Flat washer
(6.5 x19mm)
12
4
Long screw
(M4 x 30mm)
22
5
Short screw
(M3.5 x 15mm)
4
6
Steel band
2
7
Pan head screw
(M4 x 28 mm)
3
8
Wooden knob
(φ35 x 30mm)
3
9
Allen key
(M4 x 30 x 120mm)
1
NOTE: HARDWARE IS PACKED IN CARTON SV-37B.

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 5 - THIS ITEM IS PACKED IN TWO CARTONS
STEP 1
Attach side panels (B) to top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (9).
Attach bottom panel (C) to side panels (B) with bolts (1), and washers (2) and (3) as shown below.
Tighten with Allen key (9).
STEP 2

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 6 - THIS ITEM IS PACKED IN TWO CARTONS
WINE RACK ASSEMBLY.
Attach side panels (D) to the bottom panel (F) and top panel (E) with screws (4) as shown below.
Tighten with a screwdriver.
STEP 3

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 7 - THIS ITEM IS PACKED IN TWO CARTONS
WINE RACK ASSEMBLY.
GROUP 1 : Insert center panels (G) into the center panel (H).
GROUP 2 : Attach panels (K) to the panels (G) with screws (4) as shown below. Tighten with a screwdriver.
GROUP 3 : Attach panels (L) to the group 2 with screws (4) as shown below. Tighten with a screwdriver.
STEP 4

ITEM NO. : SV-37
REVISED JUL 20, 2016
Printed in Vietnam
- 8 - THIS ITEM IS PACKED IN TWO CARTONS
WINE RACK ASSEMBLY.
Insert group 3 into the unit (from step 3) as shown below.
STEP 6
Attach knobs (8) to front of drawers with pan head screws (7). Tighten with a screwdriver.
Insert the wine rack into the unit as shown below.
Attach steel bands (6) to the unit with screws (5) and attach the steel bands to the wall with screws (4)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.
STEP 5