Unfinished Furniture of Wilmington LIVE EDGE BE-9014TA User manual

ITEM NO.: BE-9014TA AND BE-9014TB
ISSUED JUN 28, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item
No.
: 90 IN LIVE EDGE BENCH
:
BE-9014TA AND BE-9014TB

ITEM NO.: BE-9014TA AND BE-9014TB
ISSUED JUN 28, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
PART LIST BE-9014TA
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top 1
B
Crossbar
1
C
Support bar
1
D
Side
decoration
2
BEFORE ASSEMBLY

ITEM NO.: BE-9014TA AND BE-9014TB
ISSUED JUN 28, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 3 -
PART LIST BE-9014TB
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
E
Base 2
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1 Short Bolt
(M8 x 35mm) 8
5 Small Spring Washer
(F6.5 x 11mm)
9
2 Long Bolt
(M6 x 60mm) 15
6 Flat Washer
(F6.5 x 13mm)
9
3 Large
Spring washer
(F8 x 11mm) 8
7
U-Washer
6
4 Large Flat Washer
(F8 x 19mm) 8
8 Allen key
(M4
x 30mm x 11
0mm)
1
NOTE: HARDWARE IS PACKED IN CARTON BE-9014TB.

ITEM NO.: BE-9014TA AND BE-9014TB
ISSUED JUN 28, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 4 -
STEP 1
Attach base (E) to top (A) with bolts (1), and washers (3) and (4) as shown below. Tighten with
Allen key (8).
STEP 2
Insert support bar (C) and crossbar (B) into bases (E) as shown below.
Attach the other base (E) to top (A) with bolts (1), and washers (3) and (4) as shown below. Tighten
with Allen key (8).






ITEM NO.: BE-9014TA AND BE-9014TB
ISSUED JUN 28, 2018
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 5 -
STEP 3
Attach crossbar (B) and support bar (C) to bases (E) with bolts (2) and u-washers (7) as shown below.
Tighten with Allen key (8).
Attach support bar (C) and side decorations (D) to top (A) with bolts (2), and washers (5) and (6) as
shown below. Tighten with Allen key (8).