Unfinished Furniture of Wilmington T-4818XBT User manual

ITEM NO.: T-4818XBT AND T-4818XP
ISSUED AUG 08, 2015
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: CANYON PEDESTAL EXTENSION TABLE
: T-4818XBT AND T-4818XP

ITEM NO.: T-4818XBT AND T-4818XP
ISSUED AUG 08, 2015
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
PART LIST T-
4
818XBT
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Top 1
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: T-4818XBT AND T-4818XP
ISSUED AUG 08, 2015
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 3 -
PART LIST T-
4
818XP
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
B Pedestal
Center 1
C Pedestal Side 2
D Leg 2
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Long Bolt
(M8x80mm) 4
2
Lock washer
(8.5x13mm)
8
3
Flat washer
(8.5x22mm)
8 4 Short Bolt
(M8x45mm) 4
5 Allen Key
(4x80mm) 1
6 Long screw
(M4x40 mm) 2
NOTE: HARDWARE IS PACKED IN CARTON T-4818XP

ITEM NO.: T-4818XBT AND T-4818XP
ISSUED AUG 08, 2015
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 4 -
STEP 1
Attach the leg (D) to the pedestal (B) with long bolts (1) and washers (2) and (3), as shown below.
Tighten with the Allen key (5).
Insert the pedestals (C) to the pedestal (B) as shown below.
STEP 2

ITEM NO.: T-4818XBT AND T-4818XP
ISSUED AUG 08, 2015
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 5 -
STEP 3
Attach the leg (D) to the pedestals (C) with long bolts (1) and washers (2) and (3) as shown below.
Tighten with the Allen key (5). Then attach legs (D) with screws (6) as shown below. Tighten with the
screwdriver.
STEP 4
Carefully put the pedestal block on the bottom side of the table top (A), attach the top to plate with
short bolts (4) and washers (2) and (3) as shown below .Tighten with the Allen key (5).

ITEM NO.: T-4818XBT AND T-4818XP
ISSUED AUG 08, 2015
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 6 -
STEP 5
Unlock the table top from both sides underneath the top as shown below.
Pull the 2 parts of the table top apart.
STEP 6
Place the butterfly leaf in the center of the open table top. Push the table top closed. Lock the
mechanism underneath 2 sides of the table top as shown below.