Unfinished Furniture of Wilmington T-148RT User manual

ITEM NO.: T-148RT AND T-148B-30 OR T-148B-36
(PACKED IN SEPARATE BOX)
REVISED DEC 05, 2015
Printed in Vietnam
- 1 -
T-148RT AND T-148B-30
T-148RT AND T-148B-36
Description : 48 IN ROUND SIENA TABLE
Item No. : T-148RT AND T-148B-30 OR T-148B-36
(PACKED IN SEPARATE BOX)
ASSEMBLY INSTRUCTIONS

ITEM NO.: T-148RT AND T-148B-30 OR T-148B-36
(PACKED IN SEPARATE BOX)
REVISED DEC 05, 2015
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.

ITEM NO.: T-148RT AND T-148B-30 OR T-148B-36
(PACKED IN SEPARATE BOX)
REVISED DEC 05, 2015
Printed in Vietnam
- 3 -
PART LIST T-148RT
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
A
Top
1
PART LIST T-148B-30 OR T-148B-36
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
B
Pedestal
1
C
Leg
4
PART LIST
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Large Flat
washer
(8.5x19mm)
8
2
Large Lock
washer
(8.5x13mm)
8
3
Hexagon nut
(M8x13mm)
8
4
Wrench
(M13mm)
1
5
Allen key
(M4x80mm)
1
6
Bolts
(M6 x 35mm)
4
7
Small Lock
washer
(6.5x11mm)
4
8
Small flat
washer
(6.5x13mm)
4
NOTE : HARDWARE IS PACKED IN CARTON T-148B-30 OR T-148B-36

ITEM NO.: T-148RT AND T-148B-30 OR T-148B-36
(PACKED IN SEPARATE BOX)
REVISED DEC 05, 2015
Printed in Vietnam
- 4 -
STEP 1
Attach the legs (C) to pedestal (B) with nuts (3), and washers (2) and (1) as shown below. Tighten with
the wrench (4).
Use the Allen key (5) to loosen the bolts and washers, remove the plate underneath the table top.
STEP 2

ITEM NO.: T-148RT AND T-148B-30 OR T-148B-36
(PACKED IN SEPARATE BOX)
REVISED DEC 05, 2015
Printed in Vietnam
- 5 -
STEP 3
Place the plate on top of the legs (C), attach with bolts (6), and washers (7) and (8) as shown below.
Tighten with the Allen key (5).
STEP 4
Carefully place the plate, pedestal and legs (from step 3) on the bottom side of the table top.
Attach the table top to the plate with bolts and washers (from step 2) as show below.
Tighten with the Allen key (5).