Uninet OKIDATA C5100 Installation and maintenance instructions

OKIDATA™C5100
CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •[email protected]
OKIDATA C5100 Printer
Given its high-quality printing and optimized performance
for all job types, the Okidata C5100 gradually became
quite popular in the global market.
UniNet Imaging Inc. offers a wide variety of toners and car-
tridge components for this machine and would like to
share some useful tips for the Okidata C5100 remanufac-
turing process.
STARTER UNIT (LEFT)
Commonly used with new printers.
STANDARD CARTRIDGE (RIGHT)
For use after starter cartridge.
BOTTOM OF CARTRIDGETOP OF CARTRIDGE
OKIDATA C5100 Toner Cartridge

1. Unlock the blue security mechanism on the toner unit by
moving it counter clockwise as shown.
2. Remove toner unit and set aside.
4. Turn the plastic cover upside down and pry open the back
side with a small flathead screwdriver as shown.
3. Separate the drum unit from the plastic cover by first remov-
ing the two screws as shown.
UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]

UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]
5. Turn it right-side up again and pry open the front side as
shown.
6. The plastic cover and drum unit can now be separated.
8. Remove the two screws from the ends of the Doctor Blade
that is connected to the end caps.
7. You are now ready to disassemble the drum unit.

UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]
9. Be careful when you are taking it out since it could be bent
or broken easily.
10. Remove the two screws located on the side of small end
cap as shown.
12. Once you have removed the screws, pull the small end cap
out.
11. Close-up view of small end cap with two screws.

13. The axle that supports the cylinder will come out along
with it.
14. Detach and remove the PCR.
15. The developer roller should come out easily. 16. Remove the big end cap by unscrewing the two screws as
shown.
UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]

17. The large end cap should easily come out. 18. Carefully remove the cylinder as shown gear-side first.
19. Apply UNINET “OPC Drum Coating Cream” #501 to pre-
serve the life of the cylinder.
20. Remove the supply roller and its components as shown.
UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]

21. Remove the Wiper Blade by first unscrewing the two
screws located on each end as shown.
22. Pry the Wiper Blade out of the clip where it is being held
from.
23. Wiper Blade removed. 24. Clean using air pressure. Reassemble when done.
UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]

25. Note: Before reinstalling the the plastic cover, you must
first install a new fuse to reset the counter and avoid any error
messages. Use Uninet Reset Fuse #9362.
26. Use a small screwdriver to lift open the toner fill plug.
27. Toner plug lifted. 28. Using a thin needle or small hook tool, pry off the plastic
adhesive tab from the waste hopper openings (two holes)
shown. This is where the waste toner will dump out during
cleaning.
UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]

CLEANING THE WASTE HOPPER
29. Use compressed air to remove any residual toner.
30. After cleaning use alcohol to clean both the cartridge and
the tab openings, then reinsert the adhesive tab.
31. Refill toner cartridge. 32. Redial plug by making sure the tab lines up with the slot.
UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]

33. To insure that the toner sensor works properly, turn the
gear located on the opposite side of the blue cap as shown.
34. A complete turn of the gear will make the white tab lift up
and disappear from the window.
35. White tab lifted. Remanufacturing concluded.
NOTES
UNINET IMAGING INC. •BROTHER 1240/1650 •ASSEMBLING THE TONER CARTRIDGEUNINET IMAGING INC. •BROTHER 1240/1650 •DISASSEMBLING THE TONER CARTRIDGE
UNINET IMAGING INC. •OKIDATA C5100 CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2008 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Summit Technologies is a division of UniNet Imaging Inc.
www.uninetimaging.com
USA •UK •EUROPE •AFRICA •JAPAN •CHINA •BRAZIL •MEXICO •ARGENTINA •VENEZUELA
11124 Washington Blvd., Culver City, CA, U.S.A. 90232 •Ph [phone] •Fx [phone] •techsuppor[email protected]