Union 62976 Assembly instructions

WARNING ADVERTENCIA
This gun safe does not
meet the safety standards
for gun safes specified in
California Penal Code Section
12088.2. It does not satisfy
the requirements of Penal
Code Section 12088.1, which
mandates that all firearms sold
in California be accompanied
by a firearms safety device or
proof of ownership, as required
by law, of a gun safe that meets
the Section 12088.2 minimum
safety standards developed by
the California Attorney General.
Esta caja fuerte para pistolas no
cumple con las normas de seguridad
para las cajas fuertes para pistolas
especificadas en la Sección 12088.2
del Código Penal de California.
No satisface los requisitos de
la Sección 12088.1 del Código
Penal, que requiere que todas las
armas de fuego que se vendan en
California estén acompañadas por
un dispositivo de seguridad de armas
de fuego o prueba de propiedad,
como lo requiere la ley, de una caja
fuerte para pistolas que cumpla con
las normas de seguridad mínimas
elaboradas por el Procurador
General de California, especificadas
en la Sección 12088.2.
Batteries sold separately.
To ensure security of your safe,
Bunker Hill Security does NOT provide replacement keys.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
REV 15l
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2015 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 15l

Page 2 For technical questions, please call 1-888-866-5797. Item 62976
Specifications
Outer Dimensions 21″ W x 15″ D x 59″ H
Inner Dimensions 20-1/2″ W x 12″ D x 49-1/2″ H
Lockbox Inner Dimensions 20-1/2″ W x 11″ D x 7-5/8″ H
Panel Features
Dual Security System for Keyed and Keyless Access
8 Digit Key Pad requires (4) “C” Batteries (included)
Green LED Code OK/Open
Red LED Low Battery
Includes
(4) 8x75mm Mounting Bolts, 8-Place Hanger Rack with
Soft Foam Inserts, 6-Place Clip Rack inside door panel
2 Brass Lockbox Keys, 3 shelves, 12 shelf mounting clips
Batteries 4 - “C” (sold separately)
IMPORTANT SAFETY INFORMATION
Installation Precautions
1. Verify that installation surface has no hidden
utility lines before drilling or driving screws.
2. Wear ANSI-approved safety
goggles during installation.
3. Mount securely before use.
4. Install only according to these instructions.
Improper installation can create hazards.
5. Keep installation area clean and well lit.
6. Keep bystanders out of the area during installation.
7. Do not install when tired or when under the
influence of alcohol, drugs or medication.
8. At least two people are needed to move this product.
9. Place the Safe on correct surface. Only use
this Safe on a stable, level, clean and dry
surface that is capable of sustaining the load.
Use Precautions
1. Keep closed and locked whenever unattended.
RISK OF CHILD ENTRAPMENT AND
SUFFOCATION.
Check inside before closing.
Do not allow children to play with or near safe.
Keep keys and codes away from children.
2. Keep clear of door when closing.
3. Position batteries in proper polarity and
do not install batteries of different types,
charge levels, or capacities together.
4. Use as intended only.
5. Inspect before every use; do not use
if parts are loose or damaged.
6. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
7. Do not store Keys inside of the Safe.
Place your emergency keys in a location
outside of the safe making sure they are
in a secure location that you can find.
8. WARNING: The brass components of this product
contain lead, a chemical known to the State
of California to cause cancer and birth defects
or other reproductive harm. (California Health
& Safety Code § 25249.5, et seq.)
9. The warnings, cautions, and instructions discussed
in this instruction manual cannot cover all possible
conditions and situations that may occur. It must
be understood by the operator that common sense
and caution are factors which cannot be built into
this product, but must be supplied by the operator.
10. The Safe is not fireproof.
NOTE: Harbor Freight Tools is not responsible
for the loss of any property stored within this safe
due to theft, fire, or any other circumstance.

Page 3For technical questions, please call 1-888-866-5797.Item 62976
Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. The Safe MUST be bolted to a wall or
a floor to deter theft and prevent tipping.
There are mounting holes in the back wall and
bottom of the safe. See Figure A below.
Mounting
Holes
Figure A: Rear Mounting Hole Locations
2. Use Anchor Bolts, or seek a bonded professional
for installation of the Safe into cement.
Note: For floor or wall mounting, use bolts of a suitable
size (not included) to bolt into wall studs or floor joists.
3. Using the back of or bottom of the Safe as a
template, mark the location of the mounting holes on
the concrete surface using a pencil or other marker.
4. Move the Safe aside, and drill four suitable pilot
holes in the mounting surface. Make certain that
the drilling path is clear and free of obstacles such
as wires, cables and electrical lines. Drill holes
should be the diameter of the Anchor Bolt sleeves.
5. Insert the Anchor Bolts into each drilled hole and
tap Bolts into concrete. Remove washer and nut
from each bolt. The Safe now has to be lifted into
position to fit over the four anchor bolts. Because of
the heavy weight of the Safe, this task should only
be done by several capable workmen. With the
Safe in position, add washers and nuts to Anchor
Bolts. By tightening the nuts in place, the sleeve
around each bolt will expand, and secure each bolt
into the concrete to secure the Safe in place.
Installing the Batteries
1. The Battery Compartment is located on the inside
of the Door. Gently slide the Battery Cover off the
Battery Compartment. See Figure F on page 7.
2. Insert four new “C” batteries (sold separately).
Position batteries in proper polarity and
do not install batteries of different types,
charge levels, or capacities together.
3. Reinstall battery cover by placing it low against the
Battery Compartment and sliding it into place.
Shelf Installation
The safe comes with three shelves and 12 Shelf mounting clips. Place the clip into the shelf
mounting rails, then place the shelf onto the clips. Be sure you use four clips per each shelf.

Page 4 For technical questions, please call 1-888-866-5797. Item 62976
Operation
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
Opening with Code
Note: The Safe comes preset with a code of 1 5 9
Note: The Yellow Light will illuminate each time a key
is pressed. If if it does not, open the safe with the key,
see below, and replace the batteries, see page 6.
1. Once the Green light is on:
a. turn the Knob counterclockwise,
b. turn the Handle clockwise, and
c. pull the Door open.
Note: The Knob and Handle remain unlocked only
for several seconds after inputting numbers.
Note: Three wrong entries will
sound an alarm and disable the Key Pad
for 20 seconds.
Three additional wrong entries will
sound an alarm and disable the Key Pad
for 5 minutes.
To stop the alarm: Open the safe with the key
and temporarily remove a battery.
Yellow Light
“Proceed”
Green Light
“Ready”
Red Light
“Low Battery”
Knob
Key
Pad
Handle
Manual
Lock Cover
Figure B: Key Pad Controls
Opening with Key
Note: The Tubular Key is used to open the safe.
The Flat Key is used for the Lock Box inside the safe.
DO NOT STORE KEYS IN SAFE!
1. Gently remove the Manual Lock Cover.
2. Insert Tubular Key into the lock and turn. Then:
a. turn the Knob counterclockwise,
b. turn the Handle clockwise, and
c. pull the Door open.
Manual
Lock Cover
Tubular
Keys
Handle
Knob
Figure C: Manual Lock

Page 5For technical questions, please call 1-888-866-5797.Item 62976
Changing the Code
Note: The Safe comes preset with a code of 1 5 9
1. Follow the instructions for opening
the Safe to open the door.
2. Make sure that the Tubular Key is
available before changing the code.
3. Keep door open during the entire procedure
of changing the code.
On the inside of the Door near the hinge, there is
the small, red, Code Reset Button. See Figure D.
Code
Reset
Button
Figure D: Code Reset Button
4. USER CODE:
a. Press the Code Reset Button until the Yellow Light
on the Front Control Panel lights up.
b. The Safe will beep twice to confirm
that the Code has been changed.
Important: If the Safe beeps three times, the code
has not been accepted. Repeat the steps above.
c. Leave the door open until the code
has been tested, see below.
5. MASTER CODE:
a. The Safe will beep twice to confirm
that the Code has been changed.
Important: If the Safe beeps three times, the code
has not been accepted. Repeat the steps above.
b. Leave the door open until the code
has been tested, see below.
6. With the door still open, TEST the new code:
a. First extend the door lock latch to the locked
position by turning Handle counterclockwise
and then turning Knob clockwise.
b. Once the latch is in the locked position,
use the new code to open the latch
and ensure that it works.
Note: If desired, make a note of the
new Code and store it in a safe place.
Closing
Keep closed and locked whenever unattended.
RISK OF CHILD ENTRAPMENT AND SUFFOCATION.
Check inside before closing.
Do not allow children to play with or near safe.
Keep keys and codes away from children.
1. Close the door and turn the Handle counterclockwise.
2. Turn the Knob clockwise.
3. Pull on the door to make certain it is properly locked. Knob
Handle
Figure E: Closing

Page 6 For technical questions, please call 1-888-866-5797. Item 62976
Maintenance
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
1. Protect the Safe from moist or wet conditions.
Moisture may cause electronic damage in
the key pad or corrosion of the steel.
2. Occasionally wipe the safe and key pad clean with
a soft dry cloth or brush. Occasionally apply a small
amount of light oil or lock lubricant to the mechanical
lock mechanism. Be careful not to get any oil or
other liquids on or near the electronic mechanism.
3. Occasionally wipe the safe and Key Pad
clean with a soft dry cloth or brush.
Replacing the Batteries
1. If the Red Light illuminates the
Batteries need to be changed.
2. Follow the instructions for opening the Safe.
3. The Battery Compartment is located on the
inside of the Door. Gently slide the Battery
Cover off the Battery Compartment.
4. Remove used batteries.
Dispose of them properly or recycle them.
5. Insert four new “C” Batteries. Position batteries in
proper polarity and do not install batteries of different
types, charge levels, or capacities together.
6. Reinstall battery cover by placing it low against the
Battery Compartment and sliding it into place.
7. After changing the batteries, test the Code and
change it as needed before closing the Door.
Battery
Cover
Figure F: Battery Compartment

Page 7For technical questions, please call 1-888-866-5797.Item 62976
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Replacement parts are not available for this item.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.