Unitech MS910 User manual

MS910 Wireless
Barcode Scanner
Quick Guide
Version 1.4
400947G
because we care
For more detail scanner setting, please go to
www.ute.com to download the user manual
and scanner configuration manager utility.

- 1- - 2-
Mini Wireless
Barcode Reader
Quick Guide
Hand Strap
SPECIFICATIONS
Light source 625nm visible red LED
Scan rate 240 scans/sec
Sensor Linear CMOS sensor
Resolution 5mil/ 0.127mm
PCS 30%
Housing Plastic(ABS)
Profile SPP, HID
Battery Life 5000 scans (1 scan/ 5 sec)
Charge Time 2 hours (fully charged)
Coverage 10M/33ft. (line of sight)
Operating Temp 0 to 50˚C (32˚F to 122˚F)
Symbologies All major 1D barcodes incl. GS1 Databar
USB Charger Cable
MS910 Wireless
Barcode Reader
Quick Guide
Quick Connection Card
NUMERIC BARCODES
1
*1*
2
*2*
3
*3*
4
*4*
5
*5*
INTRODUCTIONOUT OF THE BOX
3. LED Indicator
1. Mini USB port 4.
Exit Window
2. Trigger
(for charging only)
5. Hard Reset Button
(insert pin into the hole)

- 3-
CHARGING THE BATTERY
To scan a barcode, make sure the aiming beam crosses
every bar and space of the barcode.
1. Flip open the mini USB port on the scanner.
2. Insert the mini USB connector into the port on the
scanner and USB A connector into a USB port on
the host PC.




BEEPER INDICATION
LED INDICATION
Single long beep Power up
Single beep Good read
Single short beep The scanner reads a Code39 of
ASCII in configuration procedure
Two beeps Wireless connection
Two short beeps The scanner successfully reads
a configuration barcode
Five beeps Low power
Three beeps Wireless disconnection
Three short beeps i. The scanner reads a barcodes
while disconnected.
ii. The scanner reads an unexpected
barcode during configuration
procedure. (scan [ABORT] to abort
and start over)
Several short beeps The scanner switches from one
communication mode to another
Off
Flashing Green
Green for 2 sec
Flashing Red
Solid Red
Standby or Power off
Disconnected or Discoverable
Good Read
Low power
Charging
- 4-
Scanner
Mini USB
USB A
Host
GETTING STARTED

- 5-
GETTING CONNECTED PINCODE SETUP
1. Press the trigger for 1 second to activate the scanner.
2. Scan [DISCONNECT]
3. Scan [BT-SPP]; the scanner will emit several short beeps.
4. Select “Wireless Scanner” from discovered device list.
The default pincode is “1234”.
5. Open serial communication software with com port
(see Device Manager) properly set up.
6. The scanner will beep twice to verify the connection.
There are two modes of wireless communication:
- 6-
. E042$
BT - SPP
Pincode Start
*.E042$*
. E032$
*.E032$*
. E033$
*.E033$*
. E043$
BT - HID
*.E043$*
Disconnect
. E031$
*.E031$*
*$TX*
$TX
1. Press the trigger for 1 second to activate the scanner.
2. Scan [DISCONNECT]
3. Scan [BT-HID]; the scanner will emit several short beeps.
4. Select “Wireless Scanner” from discovered device list.
5. The wireless application may prompt you to scan
a pincode(see PINCODE SETUP section) it generated.
6. The scanner will beep twice to verify the connection.
Scan numeric barcodes (see NUMERIC BARCODES section
on the next pages) based on the pincode generated
by the wireless application.
STEP 1
Pincode Stop
Enter
STEP 4
STEP 3
STEP 2

NUMERIC BARCODES
- 7- - 8-
1
*1*
2
*2*
3
*3*
4
*4*
5
*5*
6
*6*
7
*7*
8
*8*
9
*9*
0
*0*

- 9- - 10 -
POWER OFF TIMEOUT SMARTPHONE CONNECTION
Variable Timeout
No Timeout (Scanner Always On)
*.B030$*
. B030$
SET MINUTE
*.B029$*
. B029$
SET SECOND
*.B021$*
. B021$
DISABLE
TIMEOUT
The default timeout is 3 minutes 0 second.
For example, to set the timeout as 5 minutes 30 seconds:
1. Scan [Set Minute]
2. Scan [0] & [5] on page 9 & 10.
(Range: 00 ~60)
(Range: 00 ~60)
3. Scan [Set Minute]
4. Scan [Set Second]
5. Scan [3] & [0] on page 9 & 10.
6. Scan [Set Second]
The timeout of inactivity before auto power-off.
Touch Keyboard - iOS
Touch Keyboard - Android
After enabling iOS Hotkey(disabled by default), you may simply
double-click the trigger to toggle the iPhone/iPad Touch Keyboard.
Please follow below steps to toggle Android virtual keybaord:
1. Enter “Settings”
2. Enter “Language & input”
3. In Keyboard & input window, tap “Default” to continue.
4. Turn off “Hardware - Physical keyboard”, and the Touch
Keyboard will function properly again.
. E047$
ENABLE iOS HOTKEY
Getting Connected - iOS & Android
Simply follow instruction in
5 can be skipped since iOS & Android will not require pin-code
for connection.
,in which step[BT - HID] (page 7)

- 11 - - 12 -
GENERAL SETTINGS
BEEPER
. P023$
. A007$
. F012$
ABORT
CHECK
VERSION
BEEP OFF
. F018$
READING MODE
. F002$
TRIGGER
TOGGLE
FLASH
CONTINUOUS
CONTINUOUS
AUTO OFF
. F003$
. F001$
. F005$
. F006$
. A001$
DEFAULT
BEEP ON

- 13 - - 14 -
KEYBOARD LAYOUT
. C010$
ENGLISH
(USA)
. C018$
ENGLISH
(UK)
. C011$
GERMAN
. C012$
FRENCH
. C013$
SPANISH
. C014$
ITALIAN
. C009$
JAPAN
(106 key)
CANADIAN
(TRADITIONAL)
. C034$
NORWEGIAN
. C029$
SWEDISH
. C026$
PORTUGUESE
. C031$
CANADIAN
(FRENCH)
. C025$

- 15 - - 16 -
HUNGARIAN
(101 KEY)
SWISS
(FRENCH)
. C016$
SWISS
(GERMAN)
KEYBOARD LAYOUT
. C017$
CZECH
(QWERTY)
. C022$
CZECH
(QWERTZ)
HUNGARIAN
(QWERTZ)
. C021$
. C024$
. C023$
BRAZILIAN
(PORTUGUESE)
SLOVAK
DUTCH
DANISH
BELGIAN
(AZERTY)
. C015$
ALT CODE
. C033$
. C032$
. C027$
. C028$
. C030$

- 17 - - 18 -
ENABLE SYMBOLOGIES
ENABLE
ALL CODE
. A002$
. K010$
CODE 32
. L010$
. N001$
. M010$
. L001$
UK PLESSEY
MSI
INDUSTRIAL
2 OF 5
MATRIX
2 OF 5
CODE 93
. L014$
. G010$
. N017$
. N032$
. N010$
. N026$
IATA
TELEPEN
GS1 DATABAR
GS1 DATABAR
LIMITED
GS1 DATABAR
EXPANDED