Unitech Ms912+ User manual

unitech is a registered trademark of unitech Electronics Co., Ltd

BT CCD Barcode Scanner

- MS912+ -

User's Manual

Version 1.1

unitech is a registered trademark of unitech Electronics Co., Ltd

Change Log.

Date Change Description Version

20160907 Update contents 1.1

unitech is a registered trademark of unitech Electronics Co., Ltd.

Preface

About This Manual

Thank you for purchasing the unitech product.

This manual explains how to install, operate and maintain our product.

No part of this publication may be reproduced or used in any form, or by any

electrical or mechanical means, such as photocopying, recording, or

information storage and retrieval systems, without permission in writing from

the manufacturer. The material in this manual is subject to change without

notice.

Regulatory Compliance Statements

FCC Warning Statements

This device has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference with radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference with radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

2. This device complies with FCC RF radiation exposure limits set forth for

an uncontrolled environment. To maintain compliance with FCC RF

exposure requirements, avoid direct contact to the transmitting antenna

during transmitting.

3. Any changes or modifications (including the antennas) made to this device

that are not expressly approved by the manufacturer may void the user’s

authority to operate the equipment.

Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use

only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the

potential for harmful interference to co-channel Mobile Satellite Systems.

Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and

5.725–5.850 GHz band when associated with an access point (AP).

FCC Label Statement

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

RF Radiation Exposure Statement

For body contact during operation, this device has been tested and meets FCC

RF exposure guidelines when used with an accessory that contains no metal

and that positions the handset a minimum of 1.5 cm from the body.

Use of other accessories may not ensure compliance with FCC RF exposure

guidelines.

Canadian Compliance Statement

This Class B Digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement

sur le material broilleur du Canada.

iii

unitech is a registered trademark of unitech Electronics Co., Ltd.

European Conformity Statement

unitech Electronics co., Ltd herewith declares that the unitech product is in

compliance with the essential requirements and all other provisions of the

R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low

Voltage 2006/95/EC directive.

The declaration of conformity is available for download at :

https://portal.unitech.eu/public/Safetyregulatorystatement

RoHS Statement

This device conforms to RoHS (Restriction of

Hazardous Substances) European Union regulations

that set maximum concentration limits on hazardous

materials used in electrical and electronic

equipment.

Waste electrical and electronic equipment (WEEE)

unitech has set up a policy and process to meet the EU

directive 2002/96/EC and update 2003/108/EC

concerning electronic waste disposal.

For more detailed information of the electronic waste

disposal of the products you have purchased from

unitech directly or via unitech’s resellers, you shall either

contact your local supplier or visit us at :

https://portal.unitech.eu/public/WEEE

unitech is a registered trademark of unitech Electronics Co., Ltd.

Taiwan NCC Warning Statement

交通部電信總局低功率電波輻射性電機管理辦法

第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者

均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有

干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備

之干擾。

注意事項:

1. 使用過度恐傷害視力。

2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過

1小時。

unitech is a registered trademark of unitech Electronics Co., Ltd.

Laser Information

The unitech product is certified in the U.S. to conform to the requirements of

DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1.

Class II and Class 2 products are not considered to be hazardous. The unitech

product contains internally a Visible Laser Diode (VLD) whose emissions do

not exceed the maximum limits as set forth in the above regulations. The

scanner is designed so that there is no human access to harmful laser light

during normal operation, user maintenance or prescribed service operations.

The laser safety warning label required by the DHHS/IEC for the unitech

product’s optional laser scanner module is located on the memory

compartment cover, on the back of the unit.

* Laser information only applies to the products with laser components.

CAUTION! Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous laser

light. Use of optical instruments with the scanner, including

binoculars, microscopes, and magnifying glasses, with will

increase eye damage.This does not include eyeglasses worn by

the user.

LED Information

The unitech product contains LED indicator(s) or LED ring whose luminance is

not harmful to human eyes during normal operation, user maintenance or

prescribed service operations.

*LED information only applies to the products with LED components.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Battery Notice

1. To guarantee optimal performance, it is recommended that rechargeable

batteries be replaced every year, or after 500 charging cycles are

completed. It is normal for the battery to balloon or expand after one year

or 500 cycles. Although it does not cause damage, it cannot be used

again and must be disposed of according to the location's safe battery

disposal procedures.

2. If a battery performance decreases more than 20%, the battery is at the

end of its life cycle. Stop use and ensure the battery is disposed of

properly.

3. The length of time that a battery lasts depends on the battery type and

how the device is used. Conserve the battery life by doing the following:

Avoid fully uncharging the battery because this places additional

strain on it. Several partial uncharges with frequent charges are better

than a fully uncharged battery. Charging a partially charged battery

does not cause harm to the unit.

Keep the battery cool. Avoid hot vehicles. For prolonged

storage, keep the battery at a 40% charge level.

Do not leave the battery uncharged and unused for an extended

period of time, the battery will wear out and the longevity of the

battery will be at least half of one with frequent charges.

4. Protect battery life by not over or under charging the battery.

5. Please do not leave battery unused for long time without charging it.

Despite unitech’s safety precautions, the battery pack may begin to

change shape. If so, stop using it immediately. Please check to see if you

are using a proper power adapter to charge the battery or contact your

service provider for service.

6. If you cannot charge the battery after it has been idle for an extended

period of time and it begins to heat up, please do not try to charge it. It

may not be functional anymore.

7. Please only use the original battery from unitech. Using a third party

battery can damage our products. Please note that when such damage

occurs, it is not covered by unitech’s warranty policy

vii

unitech is a registered trademark of unitech Electronics Co., Ltd.

RISK OF EXPLOSION IF BATTERY IS

REPLACED INCORRECTLY.

DISPOSE OF USED BATTERIES ACCORDING

TO THE INSTRUCTIONS..

如果更換不正確之電池行事會有爆炸的風險

請依製造商說明書處理用過之電池

CAUTION!

如果更换不正确之电池行事会有爆炸的风险

请依制造商说明书处理用过之电池

Battery charge notice

It is important to consider temperature when the battery pack is charging.

Charging is most efficient at normal room temperature or in a slightly cooler

environment. It is essential that batteries are charged within the stated range of

0°C to 40°C. Charging batteries outside of the specified range could damage

the batteries and shorten their life cycle.

CAUTION! Do not charge batteries at a temperature lower than 0°C. This will

and make the batteries unstable and dangerous. Please use a

battery temperature detecting device for a charger to ensure a

safe charging temperature range.

Storage and safety notice

Although charged batteries may be left unused for several months, their

capacity may be depleted due to build up of internal resistance. If this happens,

they will require recharging prior to use. Batteries may be stored at

temperatures between -20°C to 60°C, however they may deplete more rapidly

at higher temperatures. It is recommended to store batteries at room

temperature.

* The message above only applies to the usage of the removable batteries.

For the products with non-removable batteries / without batteries, please refer to

the specification of each product.

Product Operation and Storage Notice

The unitech product has applicable operation and storage temperature

conditions. Please follow the limitation of suggested temperature conditions to

avoid failure, damage or malfunction.

*For applicable temperature conditions, please refer to the specification of each

product.

viii

unitech is a registered trademark of unitech Electronics Co., Ltd.

Adapter Notice

1. Please do not leave the power adapter in the socket when it is not

connected to your unitech product for charging.

2. Please remove the power adapter when the battery is fully recharged.

3. The bundled power adapter that comes with your unitech product is not

meant to be used outdoors. An adapter exposed to water or rain, or a very

humid environment can cause damage to both the adapter and the

product.

4. Please only use the bundled power adapter or same specification of

adapter to charge your unitech product. Using the wrong power adapter

can damage your unitech product.

* The message above only applies to the product connected to the adapter.

For the products without using the adapters, please refer to the specification of

each product.

Hearing Damage Warning

Zx.3 Warning

The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of

the following:

- the symbol of Figure 1 with a minimum height of 5 mm; and

- the following wording, or similar :

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to

acknowledge activation of the higher level.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Worldwide Support

unitech’s professional support team is available to quickly answer questions or

assist with technical-related issues. Should an equipment problem occur,

please contact the nearest unitech regional service representative.

For complete contact information please visit the Web sites listed below:

Taipei, Taiwan – Headquarters Europe

Tel: +886-2-89121122 Tel: +31-13-4609292

E-mail: [email protected] E-mail: [email protected]

Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian

District, New Taipei City 231, Taiwan (R.O.C.)

Website: http://www.ute.com

Address:

Website:

Kapitein Hatterasstraat 19, 5015 BB,

Tilburg, the Netherlands

http://eu.ute.com

China Japan

Tel: +86-59-2310-9966 Tel: +81-3-35232766

E-mail: [email protected] E-mail: [email protected]

Address:

Website:

Room401C, 4F, RIHUA International Mansion,

Xinfeng 3nd Road, Huoju Hi-tech District,

Xiamen, Fujan , China

http://cn.ute.com

Address:

Website:

Kayabacho Nagaoka Building 8F.,1-5-19

Shinkawa, Chuo-Ku,

Tokyo, 104-0033, Japan

http://jp.ute.com

Asia & Pacific / Middle East Latin America

Tel: +886-2-27911556 Tel: +52-55-5171-0528

E-mail: [email protected]e.com

[email protected]

info@mideast.ute.com

E-mail:

Address:

[email protected]

17171 Park Row, Suite 210

Houston, TX 77084USA(Rep.)

Address: 4F., No. 236, ShinHu 2nd Rd.,

NeiHu Chiu, 114, Taipei,Taiwan Website: http://latin.ute.com

Website: http://apac.ute.com / http://mideast.ute.com

North America

Tel: +1-714-8916400

E-mail:

Address:

Website:

[email protected] / [email protected]

6182 Katella Ave, Cypress, CA90630, USA

http://us.ute.com

unitech is a registered trademark of unitech Electronics Co., Ltd.

Warranty Policy

The items covered under the unitech Limited Warranty are free from defects

during normal use.

The warranty period is varied from each country. Please consult with your

supplier or unitech local office for actual length of warranty period to your

purchased product.

Warranty becomes void if equipment is modified, improperly installed or used,

damaged by accident or neglect, or if any parts are improperly installed or

replaced by the user.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Table of Contents

Preface...........................................................................................................i

About This Manual ........................................................................................i

Regulatory Compliance Statements..............................................................i

Laser Information .........................................................................................v

LED Information ...........................................................................................v

Battery Notice..............................................................................................vi

Adapter Notice............................................................................................viii

Hearing Damage Warning..........................................................................viii

Worldwide Support......................................................................................ix

Warranty Policy ............................................................................................x

Chapter 1 - Overview................................................................................1

1.1 Package .................................................................................................1

1.2 Scanner Detail........................................................................................2

1.3 Specifications .........................................................................................3

1.4 Getting Started .......................................................................................5

1.5 Battery Charging ....................................................................................5

1.6 LED Indicator / Beeper Sequence..........................................................6

Chapter 2 – Configuration-General ......................................................7

2.1 BT HID....................................................................................................7

2.2 BT SPP.................................................................................................12

Chapter 3 –Bar Codes & Others..........................................................13

3.1 All SymboIogies....................................................................................13

3.2 MSI / UK Plessey code.........................................................................16

3.3 Code93 / Telepen / IATA.......................................................................17

3.4 Interleaved 2 of 5 / Code 11 .................................................................18

3.5 Industrial 2 of 5 / Matrix 2 of 5..............................................................19

3.6 Codabar ...............................................................................................20

3.7 ABC Codabar, CX Codabar..................................................................21

3.8 Code 39 (Full ASCII/Standard) / Code 32.............................................23

3.9 UPC-E..................................................................................................24

3.10 UPC-E(0)&(1) / UPC-E EXPAND .......................................................25

3.11 UPC-A ................................................................................................26

3.12 EAN-8.................................................................................................27

xii

unitech is a registered trademark of unitech Electronics Co., Ltd.

3.13 EAN-13 / ISSN / ISBN / ISMN............................................................28

3.14 EAN & UCC128/Code 128 .................................................................30

3.15 DataBar (RSS) ...................................................................................31

Chapter 4 – Command Setting.............................................................33

4.1 System Setting.....................................................................................33

4.2 BT Pairing.............................................................................................34

4.3 Output data transmit.............................................................................41

4.4 BT Config .............................................................................................46

4.5 Beep tone, Terminator..........................................................................50

4.6 Scan mode...........................................................................................51

4.7 Send Data Length, Preamble, Postamble ............................................52

4.8 Accuracy Adjustment............................................................................53

4.9 Code ID, Inverse Barcode....................................................................54

4.10 Power off Timeout ..............................................................................58

Appendix A – Numeric Bar Codes.......................................................59

Appendix B – Full ASCII Table(Code39)............................................60

Appendix C – Default table...................................................................71

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS912+ User’s Manual

Chapter 1 - Overview

1.1 Package

Please make sure the following contents are in the MS912+ gift box.

If something is missing or damaged, please contact your unitech

representative.

The standard package contents:

MS912+ Scanner

Quick Start Guide

Regulatory Compliance Statements

USB Charging Cable

Hand Strap

Note: To scan a barcode, make sure the aiming beam crosses every bar and

space of the barcode.

unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

1.2 Scanner Detail

Mini USB port

Hard Reset Button in the back

of MS912+ (insert pin into the hole )

Scan Window

LED lndicators

Trigger

unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

1.3 Specifications

Performance/Optical

Image Sensor Linear CMOS sensor

Light Source 625nm Visible Red LED

Max. Resolution 4 mil (0.1mm)

Scan Rate 650 scans/ second

Printing Contrast Scale 30% Minimum

Depth of Field

Reading Distance

(DOF PCS=90%)

Code 39, 4mil: 40mm (near) / 65mm (far)

Code 39, 5mil: 35mm (near) / 90mm (far)

Code 39, 10mil: 35mm (near) / 195mm (far)

Code 39, 15mil: 50mm (near) / 280mm (far)

UPC/EAN, 13mil: 35mm (near) / 230mm (far)

Functionality

Symbologies UPC-A/UPC-E, EAN-8/EAN-13, Industrial 2of 5,

Codabar, Matrix 2 of 5, Code 11, Code93, Code

32, Code 128, Standard Code 39,Full ASCII

Code 39, Interleaved 2 of 5, ChinaPostal Code,

MSI Plessy Code, UK PlessyCode, EAN/UCC

128, Telepen Code, IATACode, GS1 Databar.

Configuration Method Configuration barcodes

Electrical

Operation Voltage 3.7VDC ± 5%

Battery Type Lithium-Ion

Current Consumption Operation mode: < 145mA

Standby mode: < 55mA

Battery Duration 6000 scans/ charge

unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

Environmental

ESD Protection Functional after 4KV Contact and 8KV Air

Operating Temperature 0°C to 50°C

Storage Temperature -20°C to 60°C

Relative Humidity 0% to 95% non-condensing

Drop Test 1.5M

Communication

Range 10M (line of sight)

Host Interface supported Mini USB

Interface/Profile SPP,HID

Wireless Class Wireless Class 2

Mechanical

Housing Material ABS + PC

Dimensions L65 x ABS + PC

18mm / 2.6 x 0.9 x 0.7in

Weight 30.2g / 1.06oz

Regulation Approvals

FCC Part15B, FCC Part15C, EN301489-1-17, EN62133, EN60950-1,

EN300328, IEC 62471, NCC, TELEC, VCCI, BSMI

Accessories

Mini USB cable, Hand Strap

unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

1.4 Getting Started

Please make sure your PC or Smartphone has a built-in wireless adaptor; the

MS912+ supports both HID and SPP wireless proﬁles. If you are connecting it

to an iOS (Apple) smartphone, please follow the instruction of “Connecting via

Human Interface Device (HID) Mode”; if you are connecting it to an Android

smartphone, please follow the instruction of “Connecting via Serial Port Proﬁle

(SPP) Mode” or the instruction of “Human Interface Device (HID) Mode”.

Note: Android 2.x devices can work with MS912+ in the SPP mode ONLY.

The SPP mode or/and the HID mode are not deﬁnitely compatible with each version of

Android OS, and thus depends on the Android-based hardware speciﬁcations deﬁned

by the Android device manufacturers.

1.5 Battery Charging

1. Flip open the mini USB port on the scanner.

2. Insert the mini USB connector into the port on the scanner and USB

connector into a USB port on the host PC.

3. Please charge the scanner for at least 2 hours (until the LED indicator

turns off).

unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

1.6 LED Indicator / Beeper Sequence

Scanner LED & Beeper Indication

Green LED Red LED Beeper Remark

Power Off or

Standby - - -

See Power Off

Timeout

Charging - Solid - -

Disconnected or

Discoverable Flash - - -

Initializing Flash Flash 1 long beep -

Power Up - - 1 long beep -

Barcode

scanning w/o

proper

connection

Flash - 1 beep -

Successful

barcode scan 1 Flash - 1 beep -

Successful

Connection - - 2 beeps -

Unsuccessful

Pincode Setup - Flash

3 short

beeps Scan [Pincode

Stop] and retry

Low Power - Flash 5 beeps -

Scanner

Out of range 1 Flash - 4 beeps

(high-low-

high-low)

Move closer to

the host.

Other manuals for MS912+

Table of contents

Unitech MS912+ User manual

Popular Barcode Reader manuals by other brands