Unitech HT660e User manual

Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
HT660e Rugged Handheld Terminal
- HT660e -
Quick Reference Guide
400830G Version 1.0

Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
HT660e Product Introduction & Accessory Kit
HT660e Terminal Manual CD
Communication Cable Battery
Adaptor Kit Hand Strap
Stylus Holder

Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
HT660e Front View
LED
Touch Screen Display
Indicator
Alpha key
Power
Scan key
Function key
Communication Interface

Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
HT660e Rear View
SD Memory Slot
Bar Code Scanner
Speaker
Battery Cover
Hand Strap
& St
y
lus

Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
First Step with HT660e
Before first using the HT660e, please ensure the battery is fully charged. There
are three ways to charge your HT660e:
 Docking Station
 USB/Charging cable
 Rechargeable Lithium-Ion battery pack
NOTE: Data loss may occur if the HT660e's backup battery is not adequately
charged. Before charging the main battery, make sure the backup
battery switch is ON.
Switch On Backup Battery
Before installing a battery, locate the backup battery
switch inside the battery compartment on the left-hand
side. Please ensure that it is in the “ON” position
before charging the main battery.
Install the Battery Pack
1. Remove the battery cover.
2. Move the backup battery switch to the ON position (see the description
above).

Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
3. Insert the battery pack so that the contacts on the battery pack line up
with the contacts in the battery compartment. Fully seat the battery.
4. Cover the battery.
Supply Power to the HT660e
Connect the USB/Charging Cable to the HT660e and connect the AC adapter
to the cable’s power jack and an electrical outlet.
Or place the HT660e into the Docking Station (first connect the power supply
to the Docking Station).
Charge the Battery for the First Time
We would like to propose to charge the battery at least up to 12 hours for the
first time to use. While it normally only takes about 4 hours to charge the
battery after it's been drained, when charging the battery for the first time
please allow at least 16 hours. While charging the main battery the backup
battery should also be charged. Please make sure the backup battery has
been switched “ON” (this cannot be emphasized enough).
CAUTION: There is a high risk of data loss from RAM if the backup battery is
not fully charged. This can happen if the main battery has been
drained and the unit is not connected to the AC adaptor. For this
reason, it is crucial that the backup battery is switched on before
charging the main battery for the first time.

Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Keypad
Data can be entered via 36 keys keypad, which includes: 0~9, alpha, function,
escape, backspace, enter, scanner trigger, cursor, and on/off keys.
Enter Key
Scan Key
Function Key
Backspace Key
Escape Key
Alpha Key
Cursor Key
Space Key
Tab Key
Power Key
[ENT] The "Enter" key confirms data entry.
[FUNC] The Function Key is used in conjunction with specific
number keys to operate as Hotkeys (see next page).
[Bksp] The backspace key erases the character to the left of the
cursor.
[ESC] The escape key returns the user to a previous page.
[TAB] The Tab key moves the cursor to the next tab or next control
on a form.
[Cursor] The cursor key moves the cursor around the screen.