Unitech Ms810 Installation and operation manual

MS810 Laser Scanner

Product Reference Guide

Rev. A

This manual explains how to install, operate and maintain the Unitech MS810 Laser

Scanner.

No part of this publication may be reproduced or used in any form, or by any

electrical or mechanical means, without permission in writing from the manufacturer.

This includes electronic or mechanical means, such as photocopying, recording, or

information storage and retrieval systems. The material in this manual is subject to

change without notice.

All product names mentioned in this manual may be trademarks or registered

trademarks of their respective companies and are hereby acknowledged.

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the instructions manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

Changes or modications not expressly approved by the party responsible for

compliance could void the user‘s authority to operate the equipment.

Warranty

No warranty of any kind is made in regard to this material, including, but not limited

to, implied warranties of merchantability or tness for any particular purpose. We are

not liable for any errors contained herein or for incidental or consequential damages

in connection with furnishing, performance or use of this material. We shall be under

no liability in respect of any defect arising from fair wear and tear, willful damage,

negligence, abnormal working conditions, failure to follow the instructions and

warnings, or misuse or alteration or repair of the products without written approval.

About This Manual

Preface

Support

Unitech’s professional support team is available to quickly answer your questions

or technical-related issues. Should an equipment problem occur, please contact the

Unitech regional service representatives nearest you. Visit the websites, listed below,

for complete contact information:

UTC (China) http://www.ute.com.cn

UTT (Taipei, Taiwan) http://www.unitech.com.tw

APAC (Taipei, Taiwan) http://www.unitech-adc.com

UTJ (Japan) http://www.unitech-japan.co.jp

UTA (USA, Canada) http://www. ute.com

UTA (Latin America) http://www.latin.ute.com

UTI (Europe) http://www.unitech-europe.nl

Preface

About This Manual

FCC Compliance ................................................2

Warranty.......................................................2

Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 1

Introduction

Introducing the MS810 ...........................................6

A Tour of the MS810 .............................................7

Laser Scan Engine Specications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Decode Zone ...................................................9

Chapter 2

Installation

USB Cable Connection..........................................10

PS2 (K/B) Cable Connection .....................................11

Operating the MS810. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 3

Bar Code Setup Menu

Multi-Interface Functions - 1

Output Mode .................................................13

Buzzer/LED..................................................13

Image ......................................................13

Code ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Multi-Interface Functions - 2

Reading Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PC Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Transmit Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Language ...................................................16

Table of Contents

Chapter 4

Bar Code Symbologies

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Symbologies On/Off - 1

Code 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Code 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Symbologies On/Off - 2

Code 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Code 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Codabar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Interleaved 2 of 5..............................................18

Industrial 2 of 5 ...............................................19

Symbologies On/Off - 3

MSI ........................................................20

UPC/EAN ...................................................20

Symbologies Setup - 1

Code 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Code 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Symbologies Setup - 2

Code 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Code 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Codabar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Symbologies Setup - 3

Codabar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Interleaved 2 of 5..............................................25

Industrial 2 of 5 ...............................................26

Symbologies Setup - 4

MSI ........................................................27

UPC/EAN ...................................................27

Symbologies Setup - 5 ..........................................29

Symbologies Setup - 6

UPC/EAN ...................................................31

Edit Setup Bar Codes ...........................................32

Macro/Special Keys Setup Bar Codes..............................34

Termination String Setup Bar Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Chapter 5

Factory Default Settings

Scanner Timing/Default .........................................37

Chapter 6

Troubleshooting

Possible Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Other Product Questions ........................................40

Introducing the MS810

The Unitech MS810 1D laser bar code scanner combines the best scanning

performance and value. The device provides an accurate, easy, and fast method of

data entry and data storage for computerized information systems. It is easy to install

and does not require software or drivers to operate.

All the operating parameters are programmed by the bar code programming menu

and stored in non-volatile RAM which can retain the settings after power is turned off.

The MS810 is a powerful and reliable handheld scanner without compromise. It is

compatible with USB and K/B interfaces, and numerous congurations.

Introduction

Chapter 1

A Tour of the MS810

The following section describes the main components and features of the MR810.

No. Component Description

1. LED (Blue/Red) LED light indicates a proper decode.

2. Speaker Speaker beeps to indicate a proper decode.

3. Handle Ergonomic handle allows for an easy grip.

4. Trigger Trigger device allows for manual scanning.

5. Exit Window A scratch-resistant surface for high-quality

scans.

NOTE: When a barcode is successfully decoded, the blue LED light on the back of

the scanner will turn on and off, and the scanner will beep once. If the barcode is

not successfully read, the LED will show red and the beep will not sound.

Laser Scan Engine Specications

Performance

Light Source: 650 nm (+10/-5 nm) Laser Diode, 1mW (peak)

Depth of Field (40 mils): Up to 420 mm Min.

Scan Speed: 80 scans/sec

Max Resolution: 0.1mm (4mils) - Code 39

Print Contrast: 45% or more

Scan Angle: 38º

Reading Indicator: Blue/Red LED, Audible Beep

Interface: USB, PS/2

Symbologies: UPC/EAN/JAN, Code 39, Codabar, ITF 2/5,

Code 128, Code 11, Code 93, MSI

Electrical Characteristics

Input Voltage: 5 VDC ± 0.5V

Current - Operating: 60mA

Regulation: FCC Class A & CE & IEC60825 Class II,

CDRH: Class II

Physical Characteristics

Dimensions (L x W x H): 93mm x 61mm x 182mm

Weight: 130 g +/- 5 g (without cable)

Case Material: Rubber & ABS Plastic

Environmental Characteristics

Operating Temperature: 0ºC to 50ºC (32ºF to 122ºF)

Storage Temperature: -20ºC to 60ºC (-4ºF to 140ºF)

Operating Humidity: 10% to 85% relative humidity, non-condensing

Storage Humidity: 5% to 95% relative humidity, non-condensing

Light Level: Up to 36000 Lux

Shock: 1.5m drop onto concrete

Decode Zone

The Decode Zone is based on Symbol’s Standard Code 39 PCS=0.9 lable in a 600 lux

environment.

NOTE: Do not hold the scanner directly over a barcode at 90˚. Scanning light

bounces directly back into the scanner from the barcode label is known as

specular reection which will create a “dead zone” where decoding is difcult.

Practice a few times to nd what range of angles works best.

USB Cable Connection

Insert the plug on the free end of the USB Communications Cable into any open USB

port on the host as described below.

Reset Conguration to Defaults

If you are unsure of the scanner

conguration or have scanned the

incorrect codes, please scan the “Reset

Conguration to Defaults” barcode.

This will reset the scanner to its factory

defaults settings in USB interface.

Installation

Chapter 2

PS/2 (K/B) Cable Connection

Reset Conguration to Defaults

If you are unsure of the scanner

conguration or have scanned the

incorrect codes, please scan the “Reset

Conguration to Defaults” barcode.

This will reset the scanner to its factory

defaults settings in PS/2 interface.

To Operate the MS810

1. Be sure that Host computer is turned OFF.

2. Ensure that all connections are secure.

3. Turn on your host computer and operate the scanner in Notepad, Word or your

preferred software.

4. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default),

and press the trigger.

5. On successful decode, the blue LED light will turn on and off. The scanner will beep

once.

Maintenance

Cleaning the scan window is the only maintenance required. A dirty window may

affect scanning accuracy. Wipe the scanner window gently with a lens tissue or other

material suitable for cleaning optical material. Do not spray water or other cleaning

liquids directly onto the window.

Bar Code Setup Menu

Chapter 3

Multi-Interface Functions - 1

OUTPUT FIRMWARE VERSION RESET CONFIGURATION TO

DEFAULTS

0A 0B

OUTPUT MODE – KEYBOARD / USB OUTPUT MODE OUTPUT MODE – KEYBOARD / USB

000600 000600

GOOD READ BEEP TONE – NONE BUZZER / LED GOOD READ BEEP TONE - RESET

014200 0B142

DECODE OPTIONS REVERSE IMAGE

– ENABLE IMAGE DECODE OPTIONS REVERSE IMAGE

- DISABLE

01391 01390

DECODE OPTIONS SEND BAR CODE

ID - DISABLE CODE ID DECODE OPTIONS SEND BAR CODE

ID – AS A PREFIX

01400 01401

DECODE OPTIONS SEND BAR CODE

ID - RESET DECODE OPTIONS SEND BAR CODE

ID – AS A SUFFIX

Multi-Interface Functions - 1 (cont.)

Multi-Interface Functions - 2

SCAN MODE – SINGLE SCAN READING

MODE SCAN MODE – SINGLE SCAN

NO TRIGGER

013300 013301

SCAN MODE – MULTISCAN SCAN MODE – MULTISCAN

NO TRIGGER

013302 013303

LASER/CCD TIMEOUT – 7 SECONDS SCAN MODE - PULSE

013304 013305

LASER/CCD TIMEOUT – 5 SECONDS LASER/CCD TIMEOUT – 2 SECONDS

0134005 0134002

LASER/CCD PULSE RATE - 7 LASER/CCD PULSE RATE - 3

013507 013503

Interface - Keyboard Wedge

WEDGE MODE - AUTODETECT

Communication WEDGE MODE – SCAN SET 2

` PASS THRU

000200 000204

TRANSMIT SPEED - 0 TRANSMIT

SPEED TRANSMIT SPEED - 25

0000000 0000025

KEYBOARD COUNTRY - USA LANGUAGE KEYBOARD COUNTRY - GERMAN

0005000 0005010

KEYBOARD COUNTRY – FRANCE KEYBOARD COUNTRY - UNIVERSAL

0005009 0005025

Introduction

This section contains a list of supported symbologies with congurable settings for

each symbology.

Symbologies On/Off - 1

CODE 11 - ENABLE CODE 11 CODE 11 - DISABLE

01261 01260

CODE 39 ENABLE CODE 39 CODE 39 DISABLE

00221 00220

FULLASCII ENABLE FULLASCII DISABLE

00231 00230

Bar Code Symbologies

Chapter 4

Symbologies On/Off - 2

CODE 93 - ENABLE CODE 93 CODE 93 - DISABLE

00621 00620

CODE 128 - ENABLE CODE 128 CODE 128 - DISABLE

00691 00690

CODE 128 ISBT - ENABLE CODE 128 ISBT - DISABLE

00701 00700

CODABAR - ENABLE CODABAR CODABAR - DISABLE

00851 00850

I2OF5 - ENABLE

INTERLEAVED

2 OF 5 I2OF5 - DISABLE

00961 00960

Symbologies On/Off - 2 (cont.)

ID2OF5 - ENABLE INDUSTRIAL

2 OF 5 ID2OF5 - DISABLE

01061 01060

Symbologies On/Off - 3

MSI - ENABLE MSI MSI - DISABLE

01151 01150

UPC-A ENABLE UPC/EAN UPC-A DISABLE

00341 00340

UPC-E ENABLE UPC-E DISABLE

00351 00350

EAN-13 ENABLE EAN-13 DISABLE

00361 00360

EAN-8 ENABLE EAN-8 DISABLE

00371 00370

Other manuals for MS810

Table of contents

Popular Scanner manuals by other brands

Shining 3D

Shining 3D Transcan C user manual

Epson

Epson B11B253205 user guide

AGFA

AGFA DuoScan T2500 owner's guide

Visioneer

Visioneer Strobe XP 220 user guide

Uniden

Uniden UBC780XLT operating guide

Zebex

Zebex Z-8072 Plus Programming guide

LMI Technologies

LMI Technologies chroma+scan 24 0 Series user manual

Baracoda

Baracoda IDBlue Specifications

Datalogic

Datalogic DS2100N Quick reference guide

Plustek

Plustek PSD300 quick start guide

Leuze electronic

Leuze electronic RS4 Original operating instructions

Raven

Raven GO Simplex user manual

Epson

Epson WorkForce Pro GT-S50 Specifications

Kodak

Kodak SCAN STATION 100 user guide

Microtek

Microtek ScanMaker X12USL installation guide

Epson

Epson DS-6500 WorkForce DS-6500 Product specifications

Intermec

Intermec SE1223 user guide

Cablescan

Cablescan QS-200S instruction manual

Unitech MS810 Installation and operation manual

Popular Scanner manuals by other brands