UNITED UHR-873 User manual

Oil-Filled Radiator
INSTRUCTION MANUAL
Model UHR-873
This product is only suitable for well insulated spaces or
occasional use
DO NOT TURN THE HEATER UPSIDE-DOWN DURING OPERATION.

IMPORTANT SAFEGUARDS
1. Read the instructions carefully before use and save them for future
reference.
2. Always disconnect the heater from the main supply when not in use
and when cleaning.
3. Do not leave the heater unattended while in operation.
4. Never cover the heater as this may lead to risk of fire.
5. Keep a distance of at least 90 cm between the heater and any
combustible material, such as furniture, curtains, bedding cloths or
papers.
6. Keep the heater clean. Do not allow objects to enter the ventilation,
as this may cause electric shock, fire or damage the heater.
7. Close supervision is required when any appliance is used near or by
children.
8. Never allow the cord get in touch with wet or hot surfaces, become
twisted or be within the reach of children.
9. Do not use outdoors.
10. Do not place on or near a hot gas or electric burner.
11. Never use the appliance with a damaged cord or plug or after the
appliance has malfunctioned or has been damaged in any way.
12. Never attempt to open any part or dismantle the controls.
1. Responsibility for failure cannot be accepted if these instructions
have been ignored.
13. Do not use the appliance for anything other than its intended use.
14. This appliance is intended for household use only.
15. Follow the regulations concerning the disposal of the oil when
scraping the appliance.
16. Any repair must be referred to an authorized service agent only.
17. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent in order to avoid a hazard.
18. The heater must not be located immediately below a socket-outlet.
19. Do not use this heater in the immediate surroundings of a bath, a
shower or a swimming pool.
20. This heater is filled with a precise quantity of special oil. Repairs
requiring opening of the oil container are only to be made by the
manufacturer of his service agent who should be contacted if there is
an oil leakage.
21. The appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person

responsible for their safety
22. Children should be supervised to ensure that they do not play with
the appliance.
ASSEMBLY
Remove the heater and all the accessories from the carton.
1. Turn the heater upside down.
2. Position the wheel base assemblies between the end fins.
3. Attach them to the heater using the U-bolts and wing nuts supplied.
4. Tighten the wing nuts.
5. Turn the heater the right way up.
PARTS DESCRIPTION
1. Power switch
2. Thermostat knob
3. Handle
4. Oil filled fins
5. Castors
6. Cord storage
7. Timer
8. Fan Operation

OPERATING YOUR OIL-FILLED RADIATOR
Place the heater on the floor at least 90 cm away from the wall and any other
objects such as furniture, curtains or plants.
Make sure the power supply used corresponds to the one on the rating label.
With the thermostat control switch and the power setting switches in the '0'
position, plug the heater into the main power supply.
1. Room temperature can be adjusted using the thermostat. Turn the thermostat
knob clockwise, to increase the heat, and anti-clockwise to decrease the
temperature, until you reach the desired temperature.
2. Switch the heater to one of the following power settings.
a) Push switch one ( I )1000W
b) Push switch two ( II ) 1500W
c) Push together switches one & two (I + II) for 2500W.
c) Add separately the air blower: 400W
3. The power switch lights up, when activated.
4. Turning the thermostat control clockwise will increase the "set" temperature.
5. Turning the thermostat anti-clockwise will decrease the "set" temperature.
6. Do not cover the heater at any time during operation. There is a risk of fire if the
heater is covered.
7. Once you have finished using your heater, turn the power switches, and the
thermostat control switch to the "0" positions, and unplug from the mains supply.
Timer function
The center of the timer has a 2 position slide switch.
In the “clock symbol” position, the timer will switch the heater on and off at
times set by the segments (see “Timer setting”, below).
The position denoted by the “I”, is a timer override position and the timer will
continue to run, but power will be fed continuously to the heater. This enables
the heater to be on all the time if required.

Clock setting
The timer, as all clocks, must be set to the current time. For example, if
it is 9 a.m., turn the dial clockwise (in arrow direction) until 9 is aligned
with the triangular pointer (Fig.3).
Timer setting
Triangular Pointer
Segments
• There are 96 segments around the circumference, each segment
being equivalent to 15 minutes of time. With this timer you can preset
the time and duration of the periods that it is desired to operate the
heater, in any 24hr period. With the timer you can set your setting to
within 15 minutes and program up to 48 cycles (1 cycle = 1 “ON” + 1
“OFF”) over a period of 24 hours.
• Using your fingers, push the segments inwards or pull them
outwards.
* When the segment is in the outward position (towards the numbers
of the dial), the heater will operate during that 15 minute period.
* If the segment is in the inward position, the heater will not operate
during this period.
IMPORTANT!
• Do not turn the timer dial anticlockwise. Always turn in clockwise
direction.
• The timer is in effect an electric clock and only works when the plug is
connected to the power supply. Whenever the plug is disconnected,
the timer stops and must be reset.
Fig.3

• Please note when you first use your heater, all the segment are
outwards. You must pull outwards those segments for the
period(s) that you want the heater to work. (If you want to bypass
the timer, check that all the 96 segments are outward) (see Fig
3).
Timer operation
• Plug in the heater.
• Unless the clock is already set, turn the timer dial clockwise to
set the clock with the current time of day (see “Clock setting”).
• Pull the segments outwards for the period you want the heater to
operate. For example, Fig 4. shows that the appliance will
operate from 2 AM to 4.30 AM (10 segments outwards).
• Push the power switch.
• Once you have set the segments for the desired heating
period, your heater will cycle on and off according to these
settings.
• As long as you keep the heater plugged in, the timer will continue
to keep proper time.
Current time 9:00 AM
10 segments outwards
Fig.4

Fan Operation
1. The fan can be switched on by pushing the button of the fan on
the control panel. The fan is switched on when the push button is
in the inward position and off when the button is in the outward
position.
2. Note: The fan will only operate when the timer is either in the override
position (slide switch next to the “I” symbol) or at some point during
the timed “on” position.
CLEANING
1. Always unplug the heater before any cleaning task
2. Clean the outer surface wiping with a dumped cloth and dry carefully
3. Do not use polishing or abrasive products.
STORING YOUR OIL-FILLED RADIATOR
1. Save the box for off season storage.
2. Clean the heater following the cleaning instructions above.
3. Remove the wheel base assemblies.
4. Place the heater, and wheel assemblies in the original box, and store
in a cool and dry place.
5. If you choose to store your heater fully assembled be sure to cover it
to protect it from dust.

NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality
materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at
their end-of-life, should be disposed of separately from your
household waste.
Please dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate
collection systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies with the
requirements of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14/ 35 / EU
ErP Directive 09 / 125 / EC
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at
www.united-electronics.gr
EXCLUSIVE IMPORTER IN GREECE:
Amiridis – Savidis S.A.
87A, 17th November Str - P.C. 55534
Pylaia - Thessaloniki - Greece
T: 2310944944 | F: 2310944940
www.amiridis-savvidis.gr