UNITED SFH-1185 User manual

Instructions Manual
Safe Box
Model: SFH-1185
Thank you very much for using this product!
Before using this product, please read this user
manual to ensure that you gain the maximum benefit
from it!

Install Your Safe
Please install the safe before use it, the position of installation holes are located at the
bottom and the back of the safe.
1. Cement Material: Drill holes on the surface according to the mounting holes of the
safe, insert the expansion sleeve into the mounting hole, fixed the safe with expansion
bolts.
2. Wooden Material: Drill holes on the surface according to the mounting holes of the
safe, and fix the safe with the self-tapping screw.
When the installation is completed, please install the bat tery and change the password
at once.
Don't put the emergency key into the safe.
Operation Instructions
I. Install Battery and Initialization
(AA Alkaline dry Battery is suggested)
1.Please open the cover of the emergency lock during first use.
2.Open the safe with the emergency key.
3.Install 4 pieces of AA size (1.5V) batteries to the battery compartment which
is on the back of the door. “Hello” will be displayed on the LCD display, the safe
will go into standby mode.
Open the cover of the emergency
lock Install 4 pieces of AA size (1.5V)
batteries
II. Open & Lock the Safe
Opening the safe
1.Using the guest password: Enter a 3-6 digit code and press “#” to confirm. The LCD
display will show “OPEN” and the door will be opened automatically. The factory set
password for the end user is 123. (If you want to hide the password, you can press "#"
button before entering the password so that the LCD display will show “ - ” instead of the
password)
2.Using the administrator password: Double press “ * ”, the LCD will display “SUPER”.
Press “000000”, and then “#”. The LCD will display “CC—--”. Press “00” and “#”, the LCD
will display “OPENED” and the door will be opened automatically.
3.Using the emergency key: Open the lock cover and insert the key. The door will open.
Locking the Safe
Enter your 3-6 digits personal password while the door is closed. Press “#” to confirm the
password and “CLOSE” will be displayed on the LCD (The user can lock the safe by
pressing “#” directly without changing the password within 5 minutes after opening it).

Remark: “ERROR” will be displayed if the lock-bolt is jammed. Please open the door again
to make certain that the door is closed normally.
Changing the Password
1.Changing the end user’s password. By inserting the new 3-6 digit code and “#” while the
safe is opened, the safe will be locked.
2.Changing the hotel management password. This needs to be operated while the safe is
locked. Double press “ * ”, the LCD will display “SUPER”. Insert the hotel management
password (the factory set password for hotel is “000000”), the LCD will display “CC ——”.
Press “01” and “#”, the LCD will display “NEU”. Insert the new 6 digit code as the
password, then press “#” to confirm and the LCD will display “REPEAT”. Insert again the
new password and “#” to confirm, the LCD will display “GOOD”.
Normal Troubleshooting
Problem 1: Forgotten Administrator Password
Resolution:
1) Open the safe and remove the three screws on the back of the door.
2) Remove the door cover and press the black button for 5 seconds.
3) The LCD will display “RESET”, the administration code will be changed into the initial
administrator password “000000”.
4) Close the door cover and tighten the screws and change the administrator password.
Problem 2: There is no display on the LCD
Reason: Maybe there is not enough power of the battery
Resolution: Change the battery with new one.
Problem 3: Cannot Change the Administrator or Guest Password
Reason: The lock-bolt does not come in contact with the limit switch
Resolution: Open the back door cover and fix the position of the limit switch.
Reason: The limit switch cannot operate or the connecting wire is broken.
Resolution: Open the back door cover and change the limit switch or connect the wire.
Problem 4:The Lock-bolt will rebound automatically when closing the safe
Reason: The door is not totally closed.
Resolution: Insert the password and close the door again.
Reason: The lock-bolt cannot make contact with the limit switch
Resolution: Open the back door cover and fix the position of the limit switch
Reason: The limit switch cannot operate or the connecting wire is broken
Resolution: Open the back door cover and change the limit switch or connect the wire
Problem 5: Cannot Close the Door if the door is imbalanced
Resolution: Use a 6mm Allen Key to remove the screws of the hinge.
Adjust the position of the safe door and tighten the screws.

Care and Maintenance
1. Use AA size (1.5V) batteries;
2. Please remove the batteries if the safe is not to be used for a long time;
3. The administrator password and the emergency key should be kept
and used by the administrator only.
4. Please do not take apart the safe if any malfunction occurs. Contact
the after-sales service department for advice.
5. Any technical data and performance improvement will not be further
advised. If any question, please contact with the after sales department.
Tips
Each box comes e q u i p ped with four feet. You can install them according to your own
needs, shown as below.
EVA
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies with the requirements of
below directives:
EMC-Directive: 14/30/EU
CE Marking: 93/68/ EEC
RoHS Directive: 11/65/EU & 15/863/EU
The detailed declaration of conformity can be found at
www.united-electronics.gr
Exclusive importer in Greece:
Amiridis – Savvidis S.A.
87A, 17th Noemvriou str, P.C. 55534
Thessaloniki – Greece
T: [phone] | F: [phone]
www.amiridis-savvidis.gr