Unitronics Vision120 User manual

Unitronics 1
Vision™ OPLC™
Installation Guide
Vision120™
This guide provides basic information for Unitronics’ Vision120™.
General Description
V120 OPLCs are micro-OPLCs, rugged programmable logic
controllers that comprise an:
On-board I/O configuration
Built-in operating panel containing a graphic LCD
screen and a keypad
Communications All V120 controllers comprise 2
RS232/485 ports
Certain models comprise a
CANbus port
I/O Options On-board I/O configuration
Model-dependent; may include
digital, high-speed, and
analog I/Os
I/O Expansion Modules
Via I/O expansion port adapter,
connect up to 128 additional I/Os
per controller
Programming Write both the HMI and Ladder control application using VisiLogic freeware.
The Vision120 User Guide and the product’s technical specification sheet contain additional
information. These documents are located on the Unitronics’ Setup CD. They may also be
downloaded from the Technical Library at www.unitronics.com.
Standard Kit Contents
V120 controller Programming cable + RS232 adapter
Mounting brackets (x2) Rubber seal (mounted in back of panel)
I/O connectors (x2) Unitronics’ Setup CD
5-pin CANbus connector and CANbus network termination resistor (CANbus models)

10/06 Vision™ OPLC™ Vision120™
2Unitronics
Danger Symbols
When any of the following symbols appear, read the associated information carefully.
Symbol Meaning Description
Danger The identified danger causes physical and property damage.
Warning The identified danger could cause physical and property damage.
Caution Caution Use caution.
Before using this product, the user must read and understand this document.
All examples and diagrams are intended to aid understanding, and do not guarantee operation.
Unitronics accepts no responsibility for actual use of this product based on these examples.
Please dispose of this product according to local and national standards and regulations.
Only qualified service personnel should open this device or carry out repairs.
Failure to comply with appropriate safety guidelines can cause severe injury or property damage.
Do not attempt to use this device with parameters that exceed permissible levels.
To avoid damaging the system, do not connect/disconnect the device when power is on.
Environmental Considerations
Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,
moisture or rain, excessive heat, regular impact shocks or excessive vibration, in accordance
with the standards given in the product’s technical specification sheet.
Ventilation: 10mm space required between controller’s top/bottom edges & enclosure walls.
Do not place in water or let water leak onto the unit.
Do not allow debris to fall inside the unit during installation.
Install at maximum distance from high-voltage cables and power equipment.

Installation Guide 10/06
Unitronics 3
Mounting
Dimensions
Panel mounting
Before you begin, note that the
mounting panel cannot be more
than 5 mm thick.
1. Make a panel cut-out
measuring 92 x 92 mm
(3.622” x 3.622”).
2. Slide the controller into the
cut-out, ensuring that the
rubber seal is in place.
3. Push the 2 mounting brackets
into their slots on the sides of
the controller as shown in the
figure to the right.
4. Tighten the bracket screws
against the panel. Hold the
bracket securely against the
unit while tightening the
screw.
5. When properly mounted, the
controller is squarely situated
in the panel cut-out as shown
in the figure to the right.

10/06 Vision™ OPLC™ Vision120™
4Unitronics
DIN-rail mounting
1. Snap the controller onto the DIN rail
as shown in the figure to the right.
2. When properly mounted, the
controller is squarely situated on the
DIN-rail as shown in the figure to
the right.
I/O Modules
The controllers offer an on-board I/O configuration that differs according to the controller model; I/O
wiring diagrams are in the controller’s technical specification sheet.
Additional I/Os may be integrated into the system via I/O Expansion Modules that you plug into the
controller’s I/O expansion port. Note that the relevant wiring diagrams are in the module’s technical
specification sheet, and that an I/O adapter is required for most modules.
Wiring: General
Do not touch live wires.
Unused pins should not be connected. Ignoring this directive may damage the device.
Caution
To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·cm).
Do not use tin, solder, or any substance on stripped wire that might cause the wire
strand to break.
Use crimp terminals for wiring; use 26-14 AWG wire (0.13 mm
2
–2.08 mm
2
).
1. Strip the wire to a length of 7±0.5mm (0.250–0.300”).
2. Unscrew the terminal to its widest position before inserting a wire.
3. Insert the wire completely into the terminal to ensure a proper connection.
4. Tighten enough to keep the wire from pulling free.
Power Supply
The controller requires an external 12 or 24VDC power supply, according to the controller model.
Exact information may be found in the controller’s technical specification sheet.
Anon-isolated power supply can be used if a 0V signal is connected to the chassis.

Installation Guide 10/06
Unitronics 5
You must use an external circuit protection device.
Install an external circuit breaker. Guard against short-
circuiting in external wiring.
Double-check all wiring before turning on the power
supply.
Do not connect either the ‘Neutral or ‘Line’ signal of the
110/220VAC to device’s 0V pin.
In the event of voltage fluctuations or non-conformity to
voltage power supply specifications, connect the device
to a regulated power supply.
Earthing the Power Supply
To maximize system performance, avoid electromagnetic interference by:
Mounting the controller on a metal panel.
Earthing the controller’s power supply: connect one end of a 14 AWG wire to the chassis
signal; connect the other end to the panel.
Note: The wire used to earth the power supply must not exceed 10 cm in length. If your
conditions do not permit this, do not earth the power supply
Communication Ports
This series comprises 2 serial ports that may be set to either RS232 or RS485. Certain models also
comprise CANbus ports. Check your controller’s technical specifications.
Turn off power before making communications connections.
Caution Signals are related to the controller’s 0V; the same 0V is used by the power supply.
Always use the appropriate port adapters.
Serial Communications
The serial ports are type RJ-11 and may be set to either RS232 or RS485 via jumper as described
on page 6. By default, the ports are set to RS232.
Use RS232 to download programs from a PC, and to communicate with serial devices and
applications, such as SCADA.
Use RS485 to create a multi-drop network containing up to 32 devices.
Caution The serial ports are not isolated. If the controller is used with a non-isolated external
device, avoid potential voltage that exceeds ± 10V.
Pinouts
The pinouts below show the signals between the adapter and port.
RS232 RS485 Controller Port
Pin # Description Pin # Description
1* DTR signal
1 A signal (+)
20V reference 2(RS232 signal)
3TXD signal 3(RS232 signal)
4RXD signal 4(RS232 signal)
50V reference 5(RS232 signal)
6* DSR signal*
6 B signal (-)
Pin #1
*Standard programming cables do not provide connection points for pins 1 and 6.

10/06 Vision™ OPLC™ Vision120™
6Unitronics
RS232 to RS485: Changing Jumper Settings
Ports can be set to either RS232 or RS485 according to jumper settings.
To access the jumpers, you must open the controller, and then remove the module’s
PCB board. Before you begin, turn off the power supply, disconnect and dismount the
controller.
When a port is adapted to RS485, Pin 1 (DTR) is used for signal A, and Pin 6 (DSR)
signal is used for signal B.
If a port is set to RS485, and flow signals DTR and DSR are not used, the port can also
be used to communicate via RS232; with the appropriate cables and wiring.
Before performing these actions, touch a grounded object to discharge any electrostatic
charge.
Avoid touching the PCB board directly. Hold the PCB board by its connectors.
1. Turn power off before opening
the controller.
2. Locate the 4 slots on the sides
of the controller.
3. Using the blade of a flat-bladed
screwdriver, gently pry off the
back of the controller.
4. Gently remove the top PCB
board:
a. Use one hand to hold the top-
most PCB board by its top
and bottom connectors.
b. With the other hand, grasp
the controller, while keeping
hold of the serial ports; this
will keep the bottom board
from being removed together
with the top board.
c. Steadily pull the top board off.
5. Locate the jumpers, and then
change the jumper settings as
required. Jumper settings are
shown on page 7

Installation Guide 10/06
Unitronics 7
6. Gently replace the PCB board.
Make certain that the pins fit
correctly into their matching
receptacle.
a. Do not force the board into
place; doing so may damage
the controller.
7. Close the controller by snapping
the plastic cover back in its
place. If the card is placed
correctly, the cover will snap on
easily.
RS232/RS485 Jumper Settings
Jumper Settings RS485 Termination
Jumper RS232* RS485 Jumper ON* OFF
1 A B 3 A B
COM 1
2 A B 4 A B
5 A B 7 A B
COM 2
6 A B 8 A B
*Default factory setting.

10/06 Vision™ OPLC™ Vision120™
8Unitronics
CANbus
These controllers comprise a CANbus port. Use
this to create a decentralized control network of
up to 63 controllers, using either Unitronics’
proprietary CANbus protocol or CANopen.
The CANbus port is galvanically isolated.
CANbus Wiring
Use twisted-pair cable. DeviceNet® thick
shielded twisted pair cable is recommended.
Network terminators: These are supplied with the
controller. Place terminators at each end of the
CANbus network.
Resistance must be set to 1%, 121R,1/4W.
Connect ground signal to the earth at only one
point, near the power supply.
The network power supply need not be at the
end of the network
CANbus Connector
121
terminating
resistor
121
terminating
resistor
Circuit
protection
device
+
-
24V Power
Supply
-V
L
H
+V
PE
-V
L
H
+V
PE
-V
L
H
+V
PE
The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole
discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or
temporarily withdraw any of the forgoing from the market.
All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of
merchantability, fitness for a particular purpose, or non-infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in
this document. In no event shall Unitronics be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising
out of or in connection with the use or performance of this information.
The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other
third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them
5410-1400-5