Unitronics Vision OPLC V1040-T20B User manual

Unitronics 1
Vision™ OPLC™ Installation Guide
V1040-T20B
This guide provides basic information for Unitronics’ controllers V1040-T20B.
General Description
V1040 OPLCs are programmable logic controllers that comprise a built-in operating panel containing
a10.4” Color Touchscreen. The V1040 offers function keys along with a virtual alpha-numeric
keyboard which is automatically displayed when the application requires the operator to enter data.
Communications 2isolated RS232/RS485 ports
USB programming port (Mini-B)
Isolated CANbus port
The user can order and install an additional port. This may be
either Ethernet or serial.
Communication Function Blocks include: SMS, GPRS, MODBUS
serial/IP; Protocol FB enables PLC to communicate with almost
any external device, via serial or Ethernet communications
I/O Options V1040 supports digital, high-speed,
analog, weight and temperature
measurement I/Os via:
Snap-in I/O Modules
Plug into the back of the
controller to provide an on-
board I/O configuration
I/O Expansion Modules
Local or remote I/Os may be
added via expansion port or
CANbus.
Installation instructions and other data may be found in the module’s technical
specification sheet.
Information Mode This mode enables you to:
Calibrate the touchscreen
View & Edit operand values, COM port settings, RTC and screen
contrast/brightness settings
Stop, initialize, and reset the PLC
To enter Information Mode, press the touchscreen and maintain contact for
several seconds.
Programming
Software,
&Utilities
The Unitronics Setup CD contains VisiLogic software and other utilities
VisiLogic
Easily configure hardware and write both HMI and Ladder control
applications; the Function Block library simplifies complex tasks
such as PID. Write your application, and then download it to the
controller via the programming cable included in the kit.
Utilities
These include UniOPC server, Remote Access for remote
programming and diagnostics, and DataXport for run-time data
logging.
To learn how to use and program the controller, as well as use utilities such as
Remote Access, refer to the VisiLogic Help system.

Vision™ OPLC™, V1040-T20B
2
Removable
Memory Storage
Micro-SD card: store datalogs, Alarms, Trends,
Data Tables; export to Excel;
backup Ladder, HMI & OS and use this data to ‘clone’ PLCs.
For more data, refer to the SD
topics in the VisiLogic Help system.
Data Tables
Data tables enable you to set recipe parameters and create datalogs.
Additional product documentation is in the Technical Library, located at
www.unitronics.com
Technical support is available at the site, and from [email protected].
Standard Kit Contents
Vision controller USB programming cable
(Type A to Mini
3pin power supply connector Mounting brackets (x8)
5pin CANbus connector Rubber seal
CANbus network termination resistor Unitronics’ Setup CD
Battery (not installed)
Danger Symbols
When any of the
following symbols appear, read the associated information carefully.
Symbol Meaning Description
Danger
The identified danger causes physical and property damage.
Warning
The identified danger could cause physical and property damage.
Caution Caution Use caution.

Before using this product, the user must read and understand this document.
All examples and diagrams are intended to aid understanding,
and do not guarantee operation.
Unitronics accepts no responsibility for actual use of this prod
uct based on these examples.

Please dispose of this product according to local and national standards and regulations.
Only qualified service personnel shou
ld open this device or carry out repairs.
Failure to comply with appropriate safety guidelines
can cause severe injury or property damage.

Do not attempt to use this device with parameters that exceed permissible levels.

To avoid damaging the system, do not connect/disconnect the device when power is on.
Environmental Considerations

Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,
moisture or rain, excessive heat, regular impact shocks or excessive vibration, in accordance
with the standards given in the product’s technical specification sheet.

Ventilation: 10mm space required between controller’s top/bottom edges & enclosure walls.
Do not place in water or let water leak onto the unit.
Do not allow debris to fall inside the unit during installation.
Install at maximum distance from high-volta
ge cables and power equipment.
Installation Guide
Unitronics
Tables; export to Excel;
PLCs.
Help system.
create datalogs.
w.unitronics.com
.
ype A to Mini
-B)
carefully.
property damage.
and property damage.
ent.
tguarantee operation.
nthese examples.
and regulations.
airs.
njury or property damage.
issible levels.
ce when power is on.
or flammable gas,
evibration, in accordance
et.
dges & enclosure walls.
uipment.

Installation Guide Vision™ OPLC™, V1040-T20B
Unitronics 3
Inserting the Battery
In order to preserve data in case of power-off, you must insert the battery.
The battery is supplied taped to the battery cover on the rear of the controller.
1. Remove the battery cover shown on page 4. The polarity (+) is marked on the battery holder and
on the battery.
2. Insert the battery, ensuring that the polarity symbol on the battery is:
-facing up
-aligned with the symbol on the holder
3. Replace the battery cover.
Mounting
Dimensions
Note that the LCD screen may have a single pixel that is permanently either black or white.

Vision™ OPLC™, V1040-T20B Installation Guide
4
Unitronics
Panel Mounting
Before you begin, note that the mounting panel cannot be more than 5 mm thick.
1. Make a panel cut-out according to
the dimensions in the figure to the
right.
2. Slide the controller into the cut-
out, ensuring that the rubber seal
is in place.
3. Push the 8 mounting brackets into
their slots on the sides of the
controller as shown in the figure to
the right.
4. Tighten the bracket screws
against the panel. Hold the
bracket securely against the unit
while tightening the screw.
5. When properly mounted, the
controller is squarely situated in
the panel cut-out as shown below.

Installation Guide
Vision™ OPLC™
Unitronics
Wiring
Do not touch live wires.
Install an external circuit breaker. Guard against short-
circuiting in external wiring.
Use appropriate circuit protection devices.

Unused pins should not be connected. Ignoring this directive may damage the device.
Double-check all wiring before turning on the power supply.
Caution
To avoid
damaging the wire, do not exceed a maximum torque of 0.5

Do not use tin, solder, or any substance on stripped wire that might cause the wire
strand to break.
Install at maximum distance from high-
voltage cables and power equipment.
Wiring Procedure
Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm
2
–3.31 mm
2
).
1. Strip the wire to a length of 7±0.5mm (0.250–0.300 inches).
2. Unscrew the terminal to its widest position before inserting a wire.
3. Insert the wire completely into the terminal to ensure a proper connection.
4. Tighten enough to keep the wire from pulling free.
Power Supply
The controller V1040-T20B requires e
ither an external 12 or 24VDC power supply.
Permissible input voltage range: 10.2-28.8VDC, with less than 10% ripple.
The power supply
must include double insulation. Outputs must be rated as
SELV/PELV/Class 2/Limited Power.
Do not connect either the ‘Neutral or ‘Line’ signal of the
110/220VAC to device’s 0V pin.
Install an external circuit breaker. Guard against short-
circuiting in external wiring.
Double-check all wiring before turning on the power
supply.
In the event of voltage fluctuations or non-conformity to
voltage power supply specifications, connect the device
to a regulated power supply.
Earthing the OPLC
To maximize system performance, avoid electromagnetic interference by:
Mounting the controller on a metal panel.
Connect the functional earth terminal of the OPLC, and the
common and ground
I/Os, directly to the earth ground of your system.
For ground wiring, use the shortest and thickest possible wire.
sion™ OPLC™
,V1040-T20B
5
ng in external wiring.
may damage the device.
ue of 0.5
N·m (5 kgf·cm).
might cause the wire
wer equipment.
upply.
rated as
Cto device’s 0V pin.
dground
lines of

Vision™ OPLC™, V1040-T20B Installation Guide
6
Unitronics
Communication Ports
This series comprises a USB port, 2 RS232/RS485 serial ports and a CANbus port. An additional
port may be ordered separately and installed. This port may be either Ethernet, or serial (COM 3).
For the most updated information regarding ports and their installation, please refer to the Technical
Library at www.unitronics.com.
Turn off power before making communications connections.
Caution Always use the appropriate port adapters.
The USB port may be used for programming, OS download, and PC access.
Note that COM port 1 function is suspended when this port is physically connected to a PC.
The serial ports are type RJ-11 and may be set to either RS232 or RS485 via DIP switches, in
accordance with the table shown below.
Use RS232 to download programs from a PC, and to communicate with serial devices and
applications, such as SCADA.
Use RS485 to create a multi-drop network containing up to 32 devices.
Pinouts
The pinouts below show PLC port signals.
To connect a PC to a port that is set to RS485, remove the RS485 connector, and connect the PC to
the PLC via the programming cable. Note that this is possible only if flow control signals are not used
(which is the standard case).
RS232 RS485** Controller Port
Pin # Description Pin # Description
Pin #1
1* DTR signal
1 A signal (+)
20V reference 2(RS232 signal)
3TXD signal 3(RS232 signal)
4RXD signal 4(RS232 signal)
50V reference 5(RS232 signal)
6* DSR signal
6 B signal (-)
*Standard programming cables do not provide connection points for pins 1 and 6.
**When a port is adapted to RS485, Pin 1 (DTR) is used for signal A,
and Pin 6 (DSR) signal is used for signal B.
RS232 to RS485: Changing DIP Switch Settings
The ports are set to RS232 by factory default.
To change the settings, first remove the Snap-in I/O Module, if one is installed, and then set the
switches according to the following table.
RS232/RS485: DIP Switch Settings
The settings below are for each COM port.
Switch Settings
123456
RS232* ON ON ON OFF ON OFF
RS485 OFF OFF OFF ON OFF ON
RS485 with
termination**
ON ON OFF ON OFF ON

Installation Guide
Vision™ OPLC™
Unitronics
*Default factory setting
**Causes the unit to function as an end unit in an RS485 network
Installing a Snap-in I/O Module
Before installing a Snap-In Module,
ensure that the Communication Module Cover is
closed.
1. Remove the I/O connector cap shown on Page 4.
2. Line the circular guidelines on the Snap-in I/O Module with the slots
on the controller as shown
below.
3
Apply even pressure on all 4 corners until you hear a distinct ‘click’. The module is now installed.
Check that all sides and corners are correctly aligned.
Removing a Snap-in I/O Module
1. Locate the four buttons on the sides of the controller, two on either side.
2. Press the buttons and hold them down to open the locking mechanism.
3.
Gently rock the module from side to side, easing the module from the controller.
sion™ OPLC™
,V1040-T20B
7
cation Module Cover is
econtroller as shown
module is now installed.
troller.

Vision™ OPLC™, V1040-T20B Installation Guide
8
Unitronics
CANbus
These controllers comprise a CANbus port. Use
this to create a decentralized control network using
one of the following CAN protocols:
CANopen: 127 controllers or external
devices
CANLayer 2, J1939
Unitronics’ proprietary UniCAN: 60
controllers, (512 data bytes per scan)
The CANbus port is galvanically isolated.
CANbus Wiring
Use twisted-pair cable. DeviceNet® thick shielded
twisted pair cable is recommended.
Network terminators: These are supplied with the
controller. Place terminators at each end of the
CANbus network.
Resistance must be set to 1%, 121Q,1/4W.
Connect ground signal to the earth at only one
point, near the power supply.
The network power supply need not be at the end
of the network
CANbus Connector
The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole
discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or
temporarily withdraw any of the forgoing from the market.
All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of
merchantability, fitness for a particular purpose, or non-infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in
this document. In no event shall Unitronics be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising
out of or in connection with the use or performance of this information.
The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other
third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them.
DIG-V1040-T20B 11/10