urban ambiance UQL1402 User manual

1of2
Package Contents
C
Fixture Body
x1
A
Crossbar
Assembly
x1
B
Alternate
Mounting screw
x2
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBaseBulb100WMaximumor
(1)S19VintageMediumBase60Wbulbisrecommendedbutnotsupplied.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
STEP 1 -Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Figure 1
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2 -Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
C
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
the backplate and Fixture
Body (C) onto the
Crossbar Assembly (A)
and secure with mounting
balls. Note: The
backplate and Fixture
Body (C) should be snug
against the wall and held
tight with the mounting
balls. If it is not, adjust
the length of the
mounting screw or
alternate short mounting
(Step 2 Continued)
screw on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws or alternate short mounting screws in or out of the
crossbar until the correct length is achieved. Once the backplate
and Fixture Body (C) is secure, remove the mounting ball and
Fixture Body (C) and proceed to Step 3.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all the wire
connections. Twist the connectors until the wires are tightly joined
together. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 4 -Install the Fixture Body
A. Position the backplate and Fixture Body (C) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws or alternate short mounting screws. Secure the Fixture Body
by using the mounting balls and hand tighten the mounting balls
until snug.
Figure 4 C
Mounting
Ball
A
Backplate
Mounting Screw
or Alternate Short
Mounting Screw
Installation Instructions: UQL1402
www.urbanambiance.com

2of2
Fixture can only
be mounted in
the direction
indicated
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
8”
FINISH: WESTERN BRONZE 4.5” 9.25”
16.25”
8”
Figure 5
STEP 5 -
Your fixture is now assembled and ready to use. Enjoy!
Install Bulb and Apply Silicone Sealer
A. Install bulb onto socket and screw snugly into place.
B. Make sure the exterior wall surface and fixture backplate are free of dirt before
applying caulk. Using exterior grade caulk, caulk over top of backplate and down
both sides. Do not caulk the bottom of the fixture backplate to ensure proper
moisture drainage.
Exterior
Grade
Caulk
Backplate
S19 Vintage Bulb
(recommended
but not supplied)
www.urbanambiance.com
UQL1402