V-tech Vsmart vs001 User manual

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor.

For instructions on sensor settings, see the

User guide that came with your VS150.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

• Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

• Press and hold to enter the

registration mode.

4 – LED light

• Red for a second when the sensor is

powered on.

• Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

VS001

Wire-Free

Contact Sensor

for use with compatible

VTech telephone systems

User Guide

Before use

Install batteries to the

open/closed sensor

1. Press the latch button on the sensor to

open the battery compartment case.

2. Insert two AAA batteries into the battery

compartment.

NOTE

• Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• The batteries operate properly under the

temperature between -18°C (0°F) and 55°C (130°F).

Add and register a sensor

You need to register the Contact Sensor with

your VTech telephone system.

1. Place your telephone base into pairing

mode as per the instructions in your

telephone user guide.

2. Press and hold the pair button (P) on the

Contact sensor, until the LED light ﬂashes

red, to enter the registration mode.

The registration process takes about 90

seconds to complete.

Replacing a sensor

If you have purchased this new VS001

accessory sensor to replace an old sensor,

follow the instructions to deregister your old

sensor, and then register this new sensor to

the telephone base.

To deregister a sensor on VS150:

1. Press MENU when the phone is not in use.

2. Enter the code *33734# to access the

DEREGISTER menu.

3. Scroll to Single sensor, and then press

SELECT.

4. Scroll to the sensor you want to

deregister, and then press SELECT.

5. Press YES to conﬁrm the deregistration.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

• You will hear an alert tone, followed by

an announcement - “Open/Closed X is

open”, from the handset.

• The handset will display Open/Closed

X is open.

Test the sensor signal strength

You can mount the Contact sensor on a door,

window, or medicine cabinet that opens or

closes.

1. Take the sensor unit and magnet unit

to the desired mounting location, and

hold them at the object and the frame

respectively.

2. Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength, and then exit the sensor setup

mode.

3. Open the door, window, or medicine cabinet

again to make sure you receive alerts.

NOTE

• Move the base closer to the mounting location,

or move the sensor closer to the base, if the

sensor is out of range

• Use adhesive tape to hold the sensor

temporarily in place.

• Depending on surroundings and obstructing

factors, like walls or cabinets, the sensor may

not transmit to the base properly.

Mount the sensor

We recommend you to mount the magnet

unit on a door, window, or medicine cabinet,

and mount the sensor unit on its respective

frame.

NOTE

• Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

• Make sure you align the magnet unit with

sensor unit when mounting.

• The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

• The door images in this installation guide are

for conceptual reference only.

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

TIPS

• If there is a difference in level between the

door, window, or medicine cabinet and its

respective frame, or the frame is too narrow or

has some decorative molding, you can choose

to mount the open/closed sensor with spacer.

You can also mount the magnet unit on the

frame, and the sensor unit on the door, window,

or medicine cabinet instead.

• You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

User guide

Sensor unit

AAA battery x 2

User guide

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor.

For instructions on sensor settings, see the

User guide that came with your VS150.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

• Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

• Press and hold to enter the

registration mode.

4 – LED light

• Red for a second when the sensor is

powered on.

• Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

VS001

Wire-Free

Contact Sensor

for use with compatible

VTech telephone systems

User Guide

Before use

Install batteries to the

open/closed sensor

1. Press the latch button on the sensor to

open the battery compartment case.

2. Insert two AAA batteries into the battery

compartment.

NOTE

• Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• The batteries operate properly under the

temperature between -18°C (0°F) and 55°C (130°F).

Add and register a sensor

You need to register the Contact Sensor with

your VTech telephone system.

1. Place your telephone base into pairing

mode as per the instructions in your

telephone user guide.

2. Press and hold the pair button (P) on the

Contact sensor, until the LED light ﬂashes

red, to enter the registration mode.

The registration process takes about 90

seconds to complete.

Replacing a sensor

If you have purchased this new VS001

accessory sensor to replace an old sensor,

follow the instructions to deregister your old

sensor, and then register this new sensor to

the telephone base.

To deregister a sensor on VS150:

1. Press MENU when the phone is not in use.

2. Enter the code *33734# to access the

DEREGISTER menu.

3. Scroll to Single sensor, and then press

SELECT.

4. Scroll to the sensor you want to

deregister, and then press SELECT.

5. Press YES to conﬁrm the deregistration.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

• You will hear an alert tone, followed by

an announcement - “Open/Closed X is

open”, from the handset.

• The handset will display Open/Closed

X is open.

Test the sensor signal strength

You can mount the Contact sensor on a door,

window, or medicine cabinet that opens or

closes.

1. Take the sensor unit and magnet unit

to the desired mounting location, and

hold them at the object and the frame

respectively.

2. Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength, and then exit the sensor setup

mode.

3. Open the door, window, or medicine cabinet

again to make sure you receive alerts.

NOTE

• Move the base closer to the mounting location,

or move the sensor closer to the base, if the

sensor is out of range

• Use adhesive tape to hold the sensor

temporarily in place.

• Depending on surroundings and obstructing

factors, like walls or cabinets, the sensor may

not transmit to the base properly.

Mount the sensor

We recommend you to mount the magnet

unit on a door, window, or medicine cabinet,

and mount the sensor unit on its respective

frame.

NOTE

• Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

• Make sure you align the magnet unit with

sensor unit when mounting.

• The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

• The door images in this installation guide are

for conceptual reference only.

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

TIPS

• If there is a difference in level between the

door, window, or medicine cabinet and its

respective frame, or the frame is too narrow or

has some decorative molding, you can choose

to mount the open/closed sensor with spacer.

You can also mount the magnet unit on the

frame, and the sensor unit on the door, window,

or medicine cabinet instead.

• You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

User guide

Sensor unit

AAA battery x 2

User guide

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor.

For instructions on sensor settings, see the

User guide that came with your VS150.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

• Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

• Press and hold to enter the

registration mode.

4 – LED light

• Red for a second when the sensor is

powered on.

• Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

VS001

Wire-Free

Contact Sensor

for use with compatible

VTech telephone systems

User Guide

Before use

Install batteries to the

open/closed sensor

1. Press the latch button on the sensor to

open the battery compartment case.

2. Insert two AAA batteries into the battery

compartment.

NOTE

• Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• The batteries operate properly under the

temperature between -18°C (0°F) and 55°C (130°F).

Add and register a sensor

You need to register the Contact Sensor with

your VTech telephone system.

1. Place your telephone base into pairing

mode as per the instructions in your

telephone user guide.

2. Press and hold the pair button (P) on the

Contact sensor, until the LED light ﬂashes

red, to enter the registration mode.

The registration process takes about 90

seconds to complete.

Replacing a sensor

If you have purchased this new VS001

accessory sensor to replace an old sensor,

follow the instructions to deregister your old

sensor, and then register this new sensor to

the telephone base.

To deregister a sensor on VS150:

1. Press MENU when the phone is not in use.

2. Enter the code *33734# to access the

DEREGISTER menu.

3. Scroll to Single sensor, and then press

SELECT.

4. Scroll to the sensor you want to

deregister, and then press SELECT.

5. Press YES to conﬁrm the deregistration.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

• You will hear an alert tone, followed by

an announcement - “Open/Closed X is

open”, from the handset.

• The handset will display Open/Closed

X is open.

Test the sensor signal strength

You can mount the Contact sensor on a door,

window, or medicine cabinet that opens or

closes.

1. Take the sensor unit and magnet unit

to the desired mounting location, and

hold them at the object and the frame

respectively.

2. Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength, and then exit the sensor setup

mode.

3. Open the door, window, or medicine cabinet

again to make sure you receive alerts.

NOTE

• Move the base closer to the mounting location,

or move the sensor closer to the base, if the

sensor is out of range

• Use adhesive tape to hold the sensor

temporarily in place.

• Depending on surroundings and obstructing

factors, like walls or cabinets, the sensor may

not transmit to the base properly.

Mount the sensor

We recommend you to mount the magnet

unit on a door, window, or medicine cabinet,

and mount the sensor unit on its respective

frame.

NOTE

• Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

• Make sure you align the magnet unit with

sensor unit when mounting.

• The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

• The door images in this installation guide are

for conceptual reference only.

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

TIPS

• If there is a difference in level between the

door, window, or medicine cabinet and its

respective frame, or the frame is too narrow or

has some decorative molding, you can choose

to mount the open/closed sensor with spacer.

You can also mount the magnet unit on the

frame, and the sensor unit on the door, window,

or medicine cabinet instead.

• You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

User guide

Sensor unit

AAA battery x 2

User guide

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor.

For instructions on sensor settings, see the

User guide that came with your VS150.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

• Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

• Press and hold to enter the

registration mode.

4 – LED light

• Red for a second when the sensor is

powered on.

• Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

VS001

Wire-Free

Contact Sensor

for use with compatible

VTech telephone systems

User Guide

Before use

Install batteries to the

open/closed sensor

1. Press the latch button on the sensor to

open the battery compartment case.

2. Insert two AAA batteries into the battery

compartment.

NOTE

• Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• The batteries operate properly under the

temperature between -18°C (0°F) and 55°C (130°F).

Add and register a sensor

You need to register the Contact Sensor with

your VTech telephone system.

1. Place your telephone base into pairing

mode as per the instructions in your

telephone user guide.

2. Press and hold the pair button (P) on the

Contact sensor, until the LED light ﬂashes

red, to enter the registration mode.

The registration process takes about 90

seconds to complete.

Replacing a sensor

If you have purchased this new VS001

accessory sensor to replace an old sensor,

follow the instructions to deregister your old

sensor, and then register this new sensor to

the telephone base.

To deregister a sensor on VS150:

1. Press MENU when the phone is not in use.

2. Enter the code *33734# to access the

DEREGISTER menu.

3. Scroll to Single sensor, and then press

SELECT.

4. Scroll to the sensor you want to

deregister, and then press SELECT.

5. Press YES to conﬁrm the deregistration.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

• You will hear an alert tone, followed by

an announcement - “Open/Closed X is

open”, from the handset.

• The handset will display Open/Closed

X is open.

Test the sensor signal strength

You can mount the Contact sensor on a door,

window, or medicine cabinet that opens or

closes.

1. Take the sensor unit and magnet unit

to the desired mounting location, and

hold them at the object and the frame

respectively.

2. Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength, and then exit the sensor setup

mode.

3. Open the door, window, or medicine cabinet

again to make sure you receive alerts.

NOTE

• Move the base closer to the mounting location,

or move the sensor closer to the base, if the

sensor is out of range

• Use adhesive tape to hold the sensor

temporarily in place.

• Depending on surroundings and obstructing

factors, like walls or cabinets, the sensor may

not transmit to the base properly.

Mount the sensor

We recommend you to mount the magnet

unit on a door, window, or medicine cabinet,

and mount the sensor unit on its respective

frame.

NOTE

• Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

• Make sure you align the magnet unit with

sensor unit when mounting.

• The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

• The door images in this installation guide are

for conceptual reference only.

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

TIPS

• If there is a difference in level between the

door, window, or medicine cabinet and its

respective frame, or the frame is too narrow or

has some decorative molding, you can choose

to mount the open/closed sensor with spacer.

You can also mount the magnet unit on the

frame, and the sensor unit on the door, window,

or medicine cabinet instead.

• You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

User guide

Sensor unit

AAA battery x 2

User guide

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor.

For instructions on sensor settings, see the

User guide that came with your VS150.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

• Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

• Press and hold to enter the

registration mode.

4 – LED light

• Red for a second when the sensor is

powered on.

• Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

VS001

Wire-Free

Contact Sensor

for use with compatible

VTech telephone systems

User Guide

Before use

Install batteries to the

open/closed sensor

1. Press the latch button on the sensor to

open the battery compartment case.

2. Insert two AAA batteries into the battery

compartment.

NOTE

• Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• The batteries operate properly under the

temperature between -18°C (0°F) and 55°C (130°F).

Add and register a sensor

You need to register the Contact Sensor with

your VTech telephone system.

1. Place your telephone base into pairing

mode as per the instructions in your

telephone user guide.

2. Press and hold the pair button (P) on the

Contact sensor, until the LED light ﬂashes

red, to enter the registration mode.

The registration process takes about 90

seconds to complete.

Replacing a sensor

If you have purchased this new VS001

accessory sensor to replace an old sensor,

follow the instructions to deregister your old

sensor, and then register this new sensor to

the telephone base.

To deregister a sensor on VS150:

1. Press MENU when the phone is not in use.

2. Enter the code *33734# to access the

DEREGISTER menu.

3. Scroll to Single sensor, and then press

SELECT.

4. Scroll to the sensor you want to

deregister, and then press SELECT.

5. Press YES to conﬁrm the deregistration.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

• You will hear an alert tone, followed by

an announcement - “Open/Closed X is

open”, from the handset.

• The handset will display Open/Closed

X is open.

Test the sensor signal strength

You can mount the Contact sensor on a door,

window, or medicine cabinet that opens or

closes.

1. Take the sensor unit and magnet unit

to the desired mounting location, and

hold them at the object and the frame

respectively.

2. Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength, and then exit the sensor setup

mode.

3. Open the door, window, or medicine cabinet

again to make sure you receive alerts.

NOTE

• Move the base closer to the mounting location,

or move the sensor closer to the base, if the

sensor is out of range

• Use adhesive tape to hold the sensor

temporarily in place.

• Depending on surroundings and obstructing

factors, like walls or cabinets, the sensor may

not transmit to the base properly.

Mount the sensor

We recommend you to mount the magnet

unit on a door, window, or medicine cabinet,

and mount the sensor unit on its respective

frame.

NOTE

• Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

• Make sure you align the magnet unit with

sensor unit when mounting.

• The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

• The door images in this installation guide are

for conceptual reference only.

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

TIPS

• If there is a difference in level between the

door, window, or medicine cabinet and its

respective frame, or the frame is too narrow or

has some decorative molding, you can choose

to mount the open/closed sensor with spacer.

You can also mount the magnet unit on the

frame, and the sensor unit on the door, window,

or medicine cabinet instead.

• You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

User guide

Sensor unit

AAA battery x 2

User guide

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor.

For instructions on sensor settings, see the

User guide that came with your VS150.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

• Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

• Press and hold to enter the

registration mode.

4 – LED light

• Red for a second when the sensor is

powered on.

• Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

VS001

Wire-Free

Contact Sensor

for use with compatible

VTech telephone systems

User Guide

Before use

Install batteries to the

open/closed sensor

1. Press the latch button on the sensor to

open the battery compartment case.

2. Insert two AAA batteries into the battery

compartment.

NOTE

• Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• The batteries operate properly under the

temperature between -18°C (0°F) and 55°C (130°F).

Add and register a sensor

You need to register the Contact Sensor with

your VTech telephone system.

1. Place your telephone base into pairing

mode as per the instructions in your

telephone user guide.

2. Press and hold the pair button (P) on the

Contact sensor, until the LED light ﬂashes

red, to enter the registration mode.

The registration process takes about 90

seconds to complete.

Replacing a sensor

If you have purchased this new VS001

accessory sensor to replace an old sensor,

follow the instructions to deregister your old

sensor, and then register this new sensor to

the telephone base.

To deregister a sensor on VS150:

1. Press MENU when the phone is not in use.

2. Enter the code *33734# to access the

DEREGISTER menu.

3. Scroll to Single sensor, and then press

SELECT.

4. Scroll to the sensor you want to

deregister, and then press SELECT.

5. Press YES to conﬁrm the deregistration.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

• You will hear an alert tone, followed by

an announcement - “Open/Closed X is

open”, from the handset.

• The handset will display Open/Closed

X is open.

Test the sensor signal strength

You can mount the Contact sensor on a door,

window, or medicine cabinet that opens or

closes.

1. Take the sensor unit and magnet unit

to the desired mounting location, and

hold them at the object and the frame

respectively.

2. Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength, and then exit the sensor setup

mode.

3. Open the door, window, or medicine cabinet

again to make sure you receive alerts.

NOTE

• Move the base closer to the mounting location,

or move the sensor closer to the base, if the

sensor is out of range

• Use adhesive tape to hold the sensor

temporarily in place.

• Depending on surroundings and obstructing

factors, like walls or cabinets, the sensor may

not transmit to the base properly.

Mount the sensor

We recommend you to mount the magnet

unit on a door, window, or medicine cabinet,

and mount the sensor unit on its respective

frame.

NOTE

• Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

• Make sure you align the magnet unit with

sensor unit when mounting.

• The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

• The door images in this installation guide are

for conceptual reference only.

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

TIPS

• If there is a difference in level between the

door, window, or medicine cabinet and its

respective frame, or the frame is too narrow or

has some decorative molding, you can choose

to mount the open/closed sensor with spacer.

You can also mount the magnet unit on the

frame, and the sensor unit on the door, window,

or medicine cabinet instead.

• You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

User guide

Sensor unit

AAA battery x 2

User guide

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to

set up and register your new sensor.

For instructions on sensor settings, see the

User guide that came with your VS150.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Sensor overview

1 – Magnet unit

2 – Sensor unit

Sensor unit overview

1 – Latch button

• Press to open the battery

compartment case.

2 – Back cover

3 – Pair button

• Press and hold to enter the

registration mode.

4 – LED light

• Red for a second when the sensor is

powered on.

• Flashes red when the sensor is in the

registration mode.

5 – Battery compartment case

VS001

Wire-Free

Contact Sensor

for use with compatible

VTech telephone systems

User Guide

Before use

Install batteries to the

open/closed sensor

1. Press the latch button on the sensor to

open the battery compartment case.

2. Insert two AAA batteries into the battery

compartment.

NOTE

• Do not mix old and new batteries. Do not

mix alkaline, standard (Carbon-Zinc) or

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.

• While you insert the batteries, make sure the

polarities are correct.

• The batteries operate properly under the

temperature between -18°C (0°F) and 55°C (130°F).

Add and register a sensor

You need to register the Contact Sensor with

your VTech telephone system.

1. Place your telephone base into pairing

mode as per the instructions in your

telephone user guide.

2. Press and hold the pair button (P) on the

Contact sensor, until the LED light ﬂashes

red, to enter the registration mode.

The registration process takes about 90

seconds to complete.

Replacing a sensor

If you have purchased this new VS001

accessory sensor to replace an old sensor,

follow the instructions to deregister your old

sensor, and then register this new sensor to

the telephone base.

To deregister a sensor on VS150:

1. Press MENU when the phone is not in use.

2. Enter the code *33734# to access the

DEREGISTER menu.

3. Scroll to Single sensor, and then press

SELECT.

4. Scroll to the sensor you want to

deregister, and then press SELECT.

5. Press YES to conﬁrm the deregistration.

Check the sensor before use

1. Separate the sensor unit from the magnet

unit.

• You will hear an alert tone, followed by

an announcement - “Open/Closed X is

open”, from the handset.

• The handset will display Open/Closed

X is open.

Test the sensor signal strength

You can mount the Contact sensor on a door,

window, or medicine cabinet that opens or

closes.

1. Take the sensor unit and magnet unit

to the desired mounting location, and

hold them at the object and the frame

respectively.

2. Use your handset to enter the Settings

menu, and then the Sensor setup menu.

Follow the steps to test the sensor’s signal

strength, and then exit the sensor setup

mode.

3. Open the door, window, or medicine cabinet

again to make sure you receive alerts.

NOTE

• Move the base closer to the mounting location,

or move the sensor closer to the base, if the

sensor is out of range

• Use adhesive tape to hold the sensor

temporarily in place.

• Depending on surroundings and obstructing

factors, like walls or cabinets, the sensor may

not transmit to the base properly.

Mount the sensor

We recommend you to mount the magnet

unit on a door, window, or medicine cabinet,

and mount the sensor unit on its respective

frame.

NOTE

• Make sure the mounting surface is clean.

A textured surface or any imperfections to

a smooth surface can keep the sticker from

making a strong bond.

• Make sure you align the magnet unit with

sensor unit when mounting.

• The distance between the sensor unit and

magnet unit must be less than 1 cm (0.4 inch).

• The door images in this installation guide are

for conceptual reference only.

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

> 1 cm

(0.4 inch)

TIPS

• If there is a difference in level between the

door, window, or medicine cabinet and its

respective frame, or the frame is too narrow or

has some decorative molding, you can choose

to mount the open/closed sensor with spacer.

You can also mount the magnet unit on the

frame, and the sensor unit on the door, window,

or medicine cabinet instead.

• You can choose to mount the sensor unit with

sticker ﬁrst, and then use screws later if you

decide to mount it at that location for long term.

User guide

Sensor unit

AAA battery x 2

User guide

Magnet unit

Spacer of

sensor unit

Spacers of magnet unit

Double-sided adhesive

stickers

Screws

Small

screws

Mount with sticker

1. Attach the sticker C onto the rectangular

area at the rear side of the magnet unit,

2. Stick the magnet unit onto the door.

Mount with sticker

You can choose one out of the four spacers

with suitable height, and then add it to the

magnet unit.

1. Push the spacer towards the magnet unit

until it securely clicks into place.

2. Attach the sticker Conto the rectangular

area at the rear side of the spacer.

3. Stick the magnet unit onto the door.

Mount with sticker

1. Attach the sticker B onto the rectangular

area at the rear side of the back cover

2. Stick the sensor unit onto the frame.

-OR-

Mount with screws

1. Press the latch button on the sensor unit

to open the battery compartment case.

2. Use a pencil to mark two holes on the

desired location on the frame, with the aid

of the two holes on the back cover of the

sensor unit. Then, remove the back cover

and drill two holes into the frame.

3. Align the holes on the back cover with

the holes on the frame. Tighten the small

screws into the holes to secure the back

cover onto the frame.

4. Push the battery compartment case back

to the mounted back cover until it securely

clicks into place.

Mount spacer with sticker

1. Attach the sticker A onto the rectangular

area at the rear side of the spacer.

2. Stick the spacer onto the frame.

-OR-

Mount spacer with screws

1. Use a pencil to mark two holes on the

desired location on the frame, with the

aid of the two holes on the spacer of the

sensor unit. Then, remove the spacer and

drill two holes into the frame.

2. Align the holes on the spacer with the holes

on the frame. Tighten the large screws into the

holes to secure the spacer onto the frame.

Mount sensor unit onto spacer

3. Press the latch button on the sensor unit

to open the battery compartment case

from the back cover.

4. Align the holes on the battery

compartment back cover with the holes on

the mounted spacer.

5. Tighten the small screws into the holes to

secure the back cover of the sensor onto

the mounted spacer.

6. Push the battery compartment case back

to the mounted spacer until it securely

clicks into place.

General product care

Taking care of your sensor

Your sensor contains sophisticated electronic

parts, so it must be treated with care.

Avoid rough treatment

Place the sensor down gently. Save the original

packing materials to protect your sensor if you

ever need to ship it.

Avoid water

Your sensor can be damaged if it gets wet.

Do not use the sensor outdoors in the rain,

or handle it with wet hands. Do not install the

sensor near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your sensor

Your sensor has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Storage

When you are not going to use the sensor for

some time, remove the battery from the sensor.

Store the sensor in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the sensor. If you cannot ﬁnd the answer to your

question, call 1300 369 193 for customer service.

The display

shows

Open/Closed

X Low battery.

Press and hold CANCEL on the

handset to erase the message.

Replace the batteries with new

ones.

The sensor

does not work

at all.

Make sure two AAA batteries

are installed.

Check if the desired sensor is

on the sensor list. If the desired

sensor is not found, then it

may be deregistered from the

telephone base. Register the

sensor again.

The sensor may be out of range.

Move the sensor closer to the

telephone base.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to reduce

the risk of ﬁre, electric shock and injury, including

the following:

1. Adult setup is required.

2. Do not use this product near water. For

example, do not use it next to a bath tub, wash

bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

3. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

4. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over a

radiator or heat register.

5. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

6. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

7. Periodically examine all components for

damage.

8. Children should be supervised to ensure that

they do not play with the product.

9. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance by

a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion if a

wrong type of battery is used for the sensor unit.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order not to

create a short circuit with conductive materials.

Customer service & product warranty

Please retain this booklet with your sales receipt as

proof of the date of purchase.

Customer Service

If you require assistance in operating this product,

please call the TecHelp Information Line on 1300 369

193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com.

Voluntary Product Warranty

In addition to your Statutory Rights and subject to the

conditions below, VTech warrants that this product will

be free from any defect in materials or workmanship

under conditions of normal use for a period of 12

months from date of purchase.

VTech does not warrant that the product will be free

from defects if defects are caused by an accident,

misuse, abuse, improper installation or operation,

vermin infestations, lack of reasonable care,

unauthorised modiﬁcation, loss of parts, tampering

or attempted repair by a person not authorised by

VTech; or where the product has been damaged by

lightning or a mains power surge.To make a claim

under this Voluntary Product Warranty you must call

the TecHelp Information Line on

1300 369 193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com where a Customer

Service Representative will inform you of the product

return process. You will need to ensure that:

• You provide proof of purchase;

• Your product is suitably packaged (original

packaging is not required); and

• You have included all components from the original

purchase.

For your records

Date of purchase:

Place of purchase:

Serial number:

For Voluntary Product Warranty purposes, proof of

purchase is required so please keep your receipt.

The beneﬁts conferred by this Voluntary Product

Warranty are in addition to other rights and remedies

that are available to you under law, which cannot be

excluded. The processes for this Voluntary Product

Warranty in no way limit your rights which arise as a

result of your Statutory Rights.

This Voluntary Product Warranty is given by:

VTech Telecommunications (Australia) Pty Ltd ABN

70 136 672 627

Address: 24 Gilby Road, Mount Waverley 3149

IMPORTANT NOTE: THIS IS NOT A PRODUCT

RETURN OR SERVICE ADDRESS – PLEASE

CONTACT TECHELP BY PHONE OR EMAIL FOR

PRODUCT AND WARRANTY SUPPORT. NO

LIABILITY WILL BE ACCEPTED BY VTECH FOR

PRODUCTS RETURNED TO THIS ADDRESS

UNDER THIS VOLUNTARY PRODUCT WARRANTY.

Phone number: 1300 369 193

Email address: tcpsupport_au@vtech.com

Statutory Rights

Our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail

to be of acceptable quality and the failure does not

amount to a major failure.

Technical specifications

Frequency control Crystal controlled PLL

synthesizer

Transmit frequency 1881.792 - 1897.344 MHz

Channels 10

Sensor operating

temperature

-18°C (0°F) to 55°C (130°F)

Nominal effective

range

Actual operating range

may vary according to

environment conditions at

the time of use.

Power

requirements

2 x AAA batteries

Disclaimer

This product is not designed for security purposes.

When properly installed and maintained, this

product may in some cases reduce the risk of

burglary, ﬁre, robbery or other events occurring

without providing an alarm. VTech is not

responsible for losses, injury, or damage resulting

from the use of this product.

Vtech Telecommunications (Australia) Pty Ltd.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Specifications are subject to change without notice.

With spacer

Mount the sensor unit

Without spacer

With spacer

Without spacer

Mount the magnet unit

Mount with sticker

1. Attach the sticker C onto the rectangular

area at the rear side of the magnet unit,

2. Stick the magnet unit onto the door.

Mount with sticker

You can choose one out of the four spacers

with suitable height, and then add it to the

magnet unit.

1. Push the spacer towards the magnet unit

until it securely clicks into place.

2. Attach the sticker Conto the rectangular

area at the rear side of the spacer.

3. Stick the magnet unit onto the door.

Mount with sticker

1. Attach the sticker B onto the rectangular

area at the rear side of the back cover

2. Stick the sensor unit onto the frame.

-OR-

Mount with screws

1. Press the latch button on the sensor unit

to open the battery compartment case.

2. Use a pencil to mark two holes on the

desired location on the frame, with the aid

of the two holes on the back cover of the

sensor unit. Then, remove the back cover

and drill two holes into the frame.

3. Align the holes on the back cover with

the holes on the frame. Tighten the small

screws into the holes to secure the back

cover onto the frame.

4. Push the battery compartment case back

to the mounted back cover until it securely

clicks into place.

Mount spacer with sticker

1. Attach the sticker A onto the rectangular

area at the rear side of the spacer.

2. Stick the spacer onto the frame.

-OR-

Mount spacer with screws

1. Use a pencil to mark two holes on the

desired location on the frame, with the

aid of the two holes on the spacer of the

sensor unit. Then, remove the spacer and

drill two holes into the frame.

2. Align the holes on the spacer with the holes

on the frame. Tighten the large screws into the

holes to secure the spacer onto the frame.

Mount sensor unit onto spacer

3. Press the latch button on the sensor unit

to open the battery compartment case

from the back cover.

4. Align the holes on the battery

compartment back cover with the holes on

the mounted spacer.

5. Tighten the small screws into the holes to

secure the back cover of the sensor onto

the mounted spacer.

6. Push the battery compartment case back

to the mounted spacer until it securely

clicks into place.

General product care

Taking care of your sensor

Your sensor contains sophisticated electronic

parts, so it must be treated with care.

Avoid rough treatment

Place the sensor down gently. Save the original

packing materials to protect your sensor if you

ever need to ship it.

Avoid water

Your sensor can be damaged if it gets wet.

Do not use the sensor outdoors in the rain,

or handle it with wet hands. Do not install the

sensor near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your sensor

Your sensor has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Storage

When you are not going to use the sensor for

some time, remove the battery from the sensor.

Store the sensor in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the sensor. If you cannot ﬁnd the answer to your

question, call 1300 369 193 for customer service.

The display

shows

Open/Closed

X Low battery.

Press and hold CANCEL on the

handset to erase the message.

Replace the batteries with new

ones.

The sensor

does not work

at all.

Make sure two AAA batteries

are installed.

Check if the desired sensor is

on the sensor list. If the desired

sensor is not found, then it

may be deregistered from the

telephone base. Register the

sensor again.

The sensor may be out of range.

Move the sensor closer to the

telephone base.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to reduce

the risk of ﬁre, electric shock and injury, including

the following:

1. Adult setup is required.

2. Do not use this product near water. For

example, do not use it next to a bath tub, wash

bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

3. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

4. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over a

radiator or heat register.

5. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

6. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

7. Periodically examine all components for

damage.

8. Children should be supervised to ensure that

they do not play with the product.

9. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance by

a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion if a

wrong type of battery is used for the sensor unit.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order not to

create a short circuit with conductive materials.

Customer service & product warranty

Please retain this booklet with your sales receipt as

proof of the date of purchase.

Customer Service

If you require assistance in operating this product,

please call the TecHelp Information Line on 1300 369

193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com.

Voluntary Product Warranty

In addition to your Statutory Rights and subject to the

conditions below, VTech warrants that this product will

be free from any defect in materials or workmanship

under conditions of normal use for a period of 12

months from date of purchase.

VTech does not warrant that the product will be free

from defects if defects are caused by an accident,

misuse, abuse, improper installation or operation,

vermin infestations, lack of reasonable care,

unauthorised modiﬁcation, loss of parts, tampering

or attempted repair by a person not authorised by

VTech; or where the product has been damaged by

lightning or a mains power surge.To make a claim

under this Voluntary Product Warranty you must call

the TecHelp Information Line on

1300 369 193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com where a Customer

Service Representative will inform you of the product

return process. You will need to ensure that:

• You provide proof of purchase;

• Your product is suitably packaged (original

packaging is not required); and

• You have included all components from the original

purchase.

For your records

Date of purchase:

Place of purchase:

Serial number:

For Voluntary Product Warranty purposes, proof of

purchase is required so please keep your receipt.

The beneﬁts conferred by this Voluntary Product

Warranty are in addition to other rights and remedies

that are available to you under law, which cannot be

excluded. The processes for this Voluntary Product

Warranty in no way limit your rights which arise as a

result of your Statutory Rights.

This Voluntary Product Warranty is given by:

VTech Telecommunications (Australia) Pty Ltd ABN

70 136 672 627

Address: 24 Gilby Road, Mount Waverley 3149

IMPORTANT NOTE: THIS IS NOT A PRODUCT

RETURN OR SERVICE ADDRESS – PLEASE

CONTACT TECHELP BY PHONE OR EMAIL FOR

PRODUCT AND WARRANTY SUPPORT. NO

LIABILITY WILL BE ACCEPTED BY VTECH FOR

PRODUCTS RETURNED TO THIS ADDRESS

UNDER THIS VOLUNTARY PRODUCT WARRANTY.

Phone number: 1300 369 193

Email address: tcpsupport_au@vtech.com

Statutory Rights

Our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail

to be of acceptable quality and the failure does not

amount to a major failure.

Technical specifications

Frequency control Crystal controlled PLL

synthesizer

Transmit frequency 1881.792 - 1897.344 MHz

Channels 10

Sensor operating

temperature

-18°C (0°F) to 55°C (130°F)

Nominal effective

range

Actual operating range

may vary according to

environment conditions at

the time of use.

Power

requirements

2 x AAA batteries

Disclaimer

This product is not designed for security purposes.

When properly installed and maintained, this

product may in some cases reduce the risk of

burglary, ﬁre, robbery or other events occurring

without providing an alarm. VTech is not

responsible for losses, injury, or damage resulting

from the use of this product.

Vtech Telecommunications (Australia) Pty Ltd.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Specifications are subject to change without notice.

With spacer

Mount the sensor unit

Without spacer

With spacer

Without spacer

Mount the magnet unit

Mount with sticker

1. Attach the sticker C onto the rectangular

area at the rear side of the magnet unit,

2. Stick the magnet unit onto the door.

Mount with sticker

You can choose one out of the four spacers

with suitable height, and then add it to the

magnet unit.

1. Push the spacer towards the magnet unit

until it securely clicks into place.

2. Attach the sticker Conto the rectangular

area at the rear side of the spacer.

3. Stick the magnet unit onto the door.

Mount with sticker

1. Attach the sticker B onto the rectangular

area at the rear side of the back cover

2. Stick the sensor unit onto the frame.

-OR-

Mount with screws

1. Press the latch button on the sensor unit

to open the battery compartment case.

2. Use a pencil to mark two holes on the

desired location on the frame, with the aid

of the two holes on the back cover of the

sensor unit. Then, remove the back cover

and drill two holes into the frame.

3. Align the holes on the back cover with

the holes on the frame. Tighten the small

screws into the holes to secure the back

cover onto the frame.

4. Push the battery compartment case back

to the mounted back cover until it securely

clicks into place.

Mount spacer with sticker

1. Attach the sticker A onto the rectangular

area at the rear side of the spacer.

2. Stick the spacer onto the frame.

-OR-

Mount spacer with screws

1. Use a pencil to mark two holes on the

desired location on the frame, with the

aid of the two holes on the spacer of the

sensor unit. Then, remove the spacer and

drill two holes into the frame.

2. Align the holes on the spacer with the holes

on the frame. Tighten the large screws into the

holes to secure the spacer onto the frame.

Mount sensor unit onto spacer

3. Press the latch button on the sensor unit

to open the battery compartment case

from the back cover.

4. Align the holes on the battery

compartment back cover with the holes on

the mounted spacer.

5. Tighten the small screws into the holes to

secure the back cover of the sensor onto

the mounted spacer.

6. Push the battery compartment case back

to the mounted spacer until it securely

clicks into place.

General product care

Taking care of your sensor

Your sensor contains sophisticated electronic

parts, so it must be treated with care.

Avoid rough treatment

Place the sensor down gently. Save the original

packing materials to protect your sensor if you

ever need to ship it.

Avoid water

Your sensor can be damaged if it gets wet.

Do not use the sensor outdoors in the rain,

or handle it with wet hands. Do not install the

sensor near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your sensor

Your sensor has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Storage

When you are not going to use the sensor for

some time, remove the battery from the sensor.

Store the sensor in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the sensor. If you cannot ﬁnd the answer to your

question, call 1300 369 193 for customer service.

The display

shows

Open/Closed

X Low battery.

Press and hold CANCEL on the

handset to erase the message.

Replace the batteries with new

ones.

The sensor

does not work

at all.

Make sure two AAA batteries

are installed.

Check if the desired sensor is

on the sensor list. If the desired

sensor is not found, then it

may be deregistered from the

telephone base. Register the

sensor again.

The sensor may be out of range.

Move the sensor closer to the

telephone base.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to reduce

the risk of ﬁre, electric shock and injury, including

the following:

1. Adult setup is required.

2. Do not use this product near water. For

example, do not use it next to a bath tub, wash

bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

3. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

4. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over a

radiator or heat register.

5. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

6. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

7. Periodically examine all components for

damage.

8. Children should be supervised to ensure that

they do not play with the product.

9. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance by

a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion if a

wrong type of battery is used for the sensor unit.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order not to

create a short circuit with conductive materials.

Customer service & product warranty

Please retain this booklet with your sales receipt as

proof of the date of purchase.

Customer Service

If you require assistance in operating this product,

please call the TecHelp Information Line on 1300 369

193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com.

Voluntary Product Warranty

In addition to your Statutory Rights and subject to the

conditions below, VTech warrants that this product will

be free from any defect in materials or workmanship

under conditions of normal use for a period of 12

months from date of purchase.

VTech does not warrant that the product will be free

from defects if defects are caused by an accident,

misuse, abuse, improper installation or operation,

vermin infestations, lack of reasonable care,

unauthorised modiﬁcation, loss of parts, tampering

or attempted repair by a person not authorised by

VTech; or where the product has been damaged by

lightning or a mains power surge.To make a claim

under this Voluntary Product Warranty you must call

the TecHelp Information Line on

1300 369 193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com where a Customer

Service Representative will inform you of the product

return process. You will need to ensure that:

• You provide proof of purchase;

• Your product is suitably packaged (original

packaging is not required); and

• You have included all components from the original

purchase.

For your records

Date of purchase:

Place of purchase:

Serial number:

For Voluntary Product Warranty purposes, proof of

purchase is required so please keep your receipt.

The beneﬁts conferred by this Voluntary Product

Warranty are in addition to other rights and remedies

that are available to you under law, which cannot be

excluded. The processes for this Voluntary Product

Warranty in no way limit your rights which arise as a

result of your Statutory Rights.

This Voluntary Product Warranty is given by:

VTech Telecommunications (Australia) Pty Ltd ABN

70 136 672 627

Address: 24 Gilby Road, Mount Waverley 3149

IMPORTANT NOTE: THIS IS NOT A PRODUCT

RETURN OR SERVICE ADDRESS – PLEASE

CONTACT TECHELP BY PHONE OR EMAIL FOR

PRODUCT AND WARRANTY SUPPORT. NO

LIABILITY WILL BE ACCEPTED BY VTECH FOR

PRODUCTS RETURNED TO THIS ADDRESS

UNDER THIS VOLUNTARY PRODUCT WARRANTY.

Phone number: 1300 369 193

Email address: tcpsupport_au@vtech.com

Statutory Rights

Our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail

to be of acceptable quality and the failure does not

amount to a major failure.

Technical specifications

Frequency control Crystal controlled PLL

synthesizer

Transmit frequency 1881.792 - 1897.344 MHz

Channels 10

Sensor operating

temperature

-18°C (0°F) to 55°C (130°F)

Nominal effective

range

Actual operating range

may vary according to

environment conditions at

the time of use.

Power

requirements

2 x AAA batteries

Disclaimer

This product is not designed for security purposes.

When properly installed and maintained, this

product may in some cases reduce the risk of

burglary, ﬁre, robbery or other events occurring

without providing an alarm. VTech is not

responsible for losses, injury, or damage resulting

from the use of this product.

Vtech Telecommunications (Australia) Pty Ltd.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Specifications are subject to change without notice.

With spacer

Mount the sensor unit

Without spacer

With spacer

Without spacer

Mount the magnet unit

Mount with sticker

1. Attach the sticker C onto the rectangular

area at the rear side of the magnet unit,

2. Stick the magnet unit onto the door.

Mount with sticker

You can choose one out of the four spacers

with suitable height, and then add it to the

magnet unit.

1. Push the spacer towards the magnet unit

until it securely clicks into place.

2. Attach the sticker Conto the rectangular

area at the rear side of the spacer.

3. Stick the magnet unit onto the door.

Mount with sticker

1. Attach the sticker B onto the rectangular

area at the rear side of the back cover

2. Stick the sensor unit onto the frame.

-OR-

Mount with screws

1. Press the latch button on the sensor unit

to open the battery compartment case.

2. Use a pencil to mark two holes on the

desired location on the frame, with the aid

of the two holes on the back cover of the

sensor unit. Then, remove the back cover

and drill two holes into the frame.

3. Align the holes on the back cover with

the holes on the frame. Tighten the small

screws into the holes to secure the back

cover onto the frame.

4. Push the battery compartment case back

to the mounted back cover until it securely

clicks into place.

Mount spacer with sticker

1. Attach the sticker A onto the rectangular

area at the rear side of the spacer.

2. Stick the spacer onto the frame.

-OR-

Mount spacer with screws

1. Use a pencil to mark two holes on the

desired location on the frame, with the

aid of the two holes on the spacer of the

sensor unit. Then, remove the spacer and

drill two holes into the frame.

2. Align the holes on the spacer with the holes

on the frame. Tighten the large screws into the

holes to secure the spacer onto the frame.

Mount sensor unit onto spacer

3. Press the latch button on the sensor unit

to open the battery compartment case

from the back cover.

4. Align the holes on the battery

compartment back cover with the holes on

the mounted spacer.

5. Tighten the small screws into the holes to

secure the back cover of the sensor onto

the mounted spacer.

6. Push the battery compartment case back

to the mounted spacer until it securely

clicks into place.

General product care

Taking care of your sensor

Your sensor contains sophisticated electronic

parts, so it must be treated with care.

Avoid rough treatment

Place the sensor down gently. Save the original

packing materials to protect your sensor if you

ever need to ship it.

Avoid water

Your sensor can be damaged if it gets wet.

Do not use the sensor outdoors in the rain,

or handle it with wet hands. Do not install the

sensor near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your sensor

Your sensor has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Storage

When you are not going to use the sensor for

some time, remove the battery from the sensor.

Store the sensor in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the sensor. If you cannot ﬁnd the answer to your

question, call 1300 369 193 for customer service.

The display

shows

Open/Closed

X Low battery.

Press and hold CANCEL on the

handset to erase the message.

Replace the batteries with new

ones.

The sensor

does not work

at all.

Make sure two AAA batteries

are installed.

Check if the desired sensor is

on the sensor list. If the desired

sensor is not found, then it

may be deregistered from the

telephone base. Register the

sensor again.

The sensor may be out of range.

Move the sensor closer to the

telephone base.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to reduce

the risk of ﬁre, electric shock and injury, including

the following:

1. Adult setup is required.

2. Do not use this product near water. For

example, do not use it next to a bath tub, wash

bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

3. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

4. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over a

radiator or heat register.

5. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

6. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

7. Periodically examine all components for

damage.

8. Children should be supervised to ensure that

they do not play with the product.

9. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance by

a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion if a

wrong type of battery is used for the sensor unit.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order not to

create a short circuit with conductive materials.

Customer service & product warranty

Please retain this booklet with your sales receipt as

proof of the date of purchase.

Customer Service

If you require assistance in operating this product,

please call the TecHelp Information Line on 1300 369

193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com.

Voluntary Product Warranty

In addition to your Statutory Rights and subject to the

conditions below, VTech warrants that this product will

be free from any defect in materials or workmanship

under conditions of normal use for a period of 12

months from date of purchase.

VTech does not warrant that the product will be free

from defects if defects are caused by an accident,

misuse, abuse, improper installation or operation,

vermin infestations, lack of reasonable care,

unauthorised modiﬁcation, loss of parts, tampering

or attempted repair by a person not authorised by

VTech; or where the product has been damaged by

lightning or a mains power surge.To make a claim

under this Voluntary Product Warranty you must call

the TecHelp Information Line on

1300 369 193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com where a Customer

Service Representative will inform you of the product

return process. You will need to ensure that:

• You provide proof of purchase;

• Your product is suitably packaged (original

packaging is not required); and

• You have included all components from the original

purchase.

For your records

Date of purchase:

Place of purchase:

Serial number:

For Voluntary Product Warranty purposes, proof of

purchase is required so please keep your receipt.

The beneﬁts conferred by this Voluntary Product

Warranty are in addition to other rights and remedies

that are available to you under law, which cannot be

excluded. The processes for this Voluntary Product

Warranty in no way limit your rights which arise as a

result of your Statutory Rights.

This Voluntary Product Warranty is given by:

VTech Telecommunications (Australia) Pty Ltd ABN

70 136 672 627

Address: 24 Gilby Road, Mount Waverley 3149

IMPORTANT NOTE: THIS IS NOT A PRODUCT

RETURN OR SERVICE ADDRESS – PLEASE

CONTACT TECHELP BY PHONE OR EMAIL FOR

PRODUCT AND WARRANTY SUPPORT. NO

LIABILITY WILL BE ACCEPTED BY VTECH FOR

PRODUCTS RETURNED TO THIS ADDRESS

UNDER THIS VOLUNTARY PRODUCT WARRANTY.

Phone number: 1300 369 193

Email address: tcpsupport_au@vtech.com

Statutory Rights

Our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail

to be of acceptable quality and the failure does not

amount to a major failure.

Technical specifications

Frequency control Crystal controlled PLL

synthesizer

Transmit frequency 1881.792 - 1897.344 MHz

Channels 10

Sensor operating

temperature

-18°C (0°F) to 55°C (130°F)

Nominal effective

range

Actual operating range

may vary according to

environment conditions at

the time of use.

Power

requirements

2 x AAA batteries

Disclaimer

This product is not designed for security purposes.

When properly installed and maintained, this

product may in some cases reduce the risk of

burglary, ﬁre, robbery or other events occurring

without providing an alarm. VTech is not

responsible for losses, injury, or damage resulting

from the use of this product.

Vtech Telecommunications (Australia) Pty Ltd.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Specifications are subject to change without notice.

With spacer

Mount the sensor unit

Without spacer

With spacer

Without spacer

Mount the magnet unit

Mount with sticker

1. Attach the sticker C onto the rectangular

area at the rear side of the magnet unit,

2. Stick the magnet unit onto the door.

Mount with sticker

You can choose one out of the four spacers

with suitable height, and then add it to the

magnet unit.

1. Push the spacer towards the magnet unit

until it securely clicks into place.

2. Attach the sticker Conto the rectangular

area at the rear side of the spacer.

3. Stick the magnet unit onto the door.

Mount with sticker

1. Attach the sticker B onto the rectangular

area at the rear side of the back cover

2. Stick the sensor unit onto the frame.

-OR-

Mount with screws

1. Press the latch button on the sensor unit

to open the battery compartment case.

2. Use a pencil to mark two holes on the

desired location on the frame, with the aid

of the two holes on the back cover of the

sensor unit. Then, remove the back cover

and drill two holes into the frame.

3. Align the holes on the back cover with

the holes on the frame. Tighten the small

screws into the holes to secure the back

cover onto the frame.

4. Push the battery compartment case back

to the mounted back cover until it securely

clicks into place.

Mount spacer with sticker

1. Attach the sticker A onto the rectangular

area at the rear side of the spacer.

2. Stick the spacer onto the frame.

-OR-

Mount spacer with screws

1. Use a pencil to mark two holes on the

desired location on the frame, with the

aid of the two holes on the spacer of the

sensor unit. Then, remove the spacer and

drill two holes into the frame.

2. Align the holes on the spacer with the holes

on the frame. Tighten the large screws into the

holes to secure the spacer onto the frame.

Mount sensor unit onto spacer

3. Press the latch button on the sensor unit

to open the battery compartment case

from the back cover.

4. Align the holes on the battery

compartment back cover with the holes on

the mounted spacer.

5. Tighten the small screws into the holes to

secure the back cover of the sensor onto

the mounted spacer.

6. Push the battery compartment case back

to the mounted spacer until it securely

clicks into place.

General product care

Taking care of your sensor

Your sensor contains sophisticated electronic

parts, so it must be treated with care.

Avoid rough treatment

Place the sensor down gently. Save the original

packing materials to protect your sensor if you

ever need to ship it.

Avoid water

Your sensor can be damaged if it gets wet.

Do not use the sensor outdoors in the rain,

or handle it with wet hands. Do not install the

sensor near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your sensor

Your sensor has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Storage

When you are not going to use the sensor for

some time, remove the battery from the sensor.

Store the sensor in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the sensor. If you cannot ﬁnd the answer to your

question, call 1300 369 193 for customer service.

The display

shows

Open/Closed

X Low battery.

Press and hold CANCEL on the

handset to erase the message.

Replace the batteries with new

ones.

The sensor

does not work

at all.

Make sure two AAA batteries

are installed.

Check if the desired sensor is

on the sensor list. If the desired

sensor is not found, then it

may be deregistered from the

telephone base. Register the

sensor again.

The sensor may be out of range.

Move the sensor closer to the

telephone base.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to reduce

the risk of ﬁre, electric shock and injury, including

the following:

1. Adult setup is required.

2. Do not use this product near water. For

example, do not use it next to a bath tub, wash

bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

3. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

4. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over a

radiator or heat register.

5. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

6. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

7. Periodically examine all components for

damage.

8. Children should be supervised to ensure that

they do not play with the product.

9. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance by

a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion if a

wrong type of battery is used for the sensor unit.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order not to

create a short circuit with conductive materials.

Customer service & product warranty

Please retain this booklet with your sales receipt as

proof of the date of purchase.

Customer Service

If you require assistance in operating this product,

please call the TecHelp Information Line on 1300 369

193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com.

Voluntary Product Warranty

In addition to your Statutory Rights and subject to the

conditions below, VTech warrants that this product will

be free from any defect in materials or workmanship

under conditions of normal use for a period of 12

months from date of purchase.

VTech does not warrant that the product will be free

from defects if defects are caused by an accident,

misuse, abuse, improper installation or operation,

vermin infestations, lack of reasonable care,

unauthorised modiﬁcation, loss of parts, tampering

or attempted repair by a person not authorised by

VTech; or where the product has been damaged by

lightning or a mains power surge.To make a claim

under this Voluntary Product Warranty you must call

the TecHelp Information Line on

1300 369 193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com where a Customer

Service Representative will inform you of the product

return process. You will need to ensure that:

• You provide proof of purchase;

• Your product is suitably packaged (original

packaging is not required); and

• You have included all components from the original

purchase.

For your records

Date of purchase:

Place of purchase:

Serial number:

For Voluntary Product Warranty purposes, proof of

purchase is required so please keep your receipt.

The beneﬁts conferred by this Voluntary Product

Warranty are in addition to other rights and remedies

that are available to you under law, which cannot be

excluded. The processes for this Voluntary Product

Warranty in no way limit your rights which arise as a

result of your Statutory Rights.

This Voluntary Product Warranty is given by:

VTech Telecommunications (Australia) Pty Ltd ABN

70 136 672 627

Address: 24 Gilby Road, Mount Waverley 3149

IMPORTANT NOTE: THIS IS NOT A PRODUCT

RETURN OR SERVICE ADDRESS – PLEASE

CONTACT TECHELP BY PHONE OR EMAIL FOR

PRODUCT AND WARRANTY SUPPORT. NO

LIABILITY WILL BE ACCEPTED BY VTECH FOR

PRODUCTS RETURNED TO THIS ADDRESS

UNDER THIS VOLUNTARY PRODUCT WARRANTY.

Phone number: 1300 369 193

Email address: tcpsupport_au@vtech.com

Statutory Rights

Our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail

to be of acceptable quality and the failure does not

amount to a major failure.

Technical specifications

Frequency control Crystal controlled PLL

synthesizer

Transmit frequency 1881.792 - 1897.344 MHz

Channels 10

Sensor operating

temperature

-18°C (0°F) to 55°C (130°F)

Nominal effective

range

Actual operating range

may vary according to

environment conditions at

the time of use.

Power

requirements

2 x AAA batteries

Disclaimer

This product is not designed for security purposes.

When properly installed and maintained, this

product may in some cases reduce the risk of

burglary, ﬁre, robbery or other events occurring

without providing an alarm. VTech is not

responsible for losses, injury, or damage resulting

from the use of this product.

Vtech Telecommunications (Australia) Pty Ltd.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Specifications are subject to change without notice.

With spacer

Mount the sensor unit

Without spacer

With spacer

Without spacer

Mount the magnet unit

Mount with sticker

1. Attach the sticker C onto the rectangular

area at the rear side of the magnet unit,

2. Stick the magnet unit onto the door.

Mount with sticker

You can choose one out of the four spacers

with suitable height, and then add it to the

magnet unit.

1. Push the spacer towards the magnet unit

until it securely clicks into place.

2. Attach the sticker Conto the rectangular

area at the rear side of the spacer.

3. Stick the magnet unit onto the door.

Mount with sticker

1. Attach the sticker B onto the rectangular

area at the rear side of the back cover

2. Stick the sensor unit onto the frame.

-OR-

Mount with screws

1. Press the latch button on the sensor unit

to open the battery compartment case.

2. Use a pencil to mark two holes on the

desired location on the frame, with the aid

of the two holes on the back cover of the

sensor unit. Then, remove the back cover

and drill two holes into the frame.

3. Align the holes on the back cover with

the holes on the frame. Tighten the small

screws into the holes to secure the back

cover onto the frame.

4. Push the battery compartment case back

to the mounted back cover until it securely

clicks into place.

Mount spacer with sticker

1. Attach the sticker A onto the rectangular

area at the rear side of the spacer.

2. Stick the spacer onto the frame.

-OR-

Mount spacer with screws

1. Use a pencil to mark two holes on the

desired location on the frame, with the

aid of the two holes on the spacer of the

sensor unit. Then, remove the spacer and

drill two holes into the frame.

2. Align the holes on the spacer with the holes

on the frame. Tighten the large screws into the

holes to secure the spacer onto the frame.

Mount sensor unit onto spacer

3. Press the latch button on the sensor unit

to open the battery compartment case

from the back cover.

4. Align the holes on the battery

compartment back cover with the holes on

the mounted spacer.

5. Tighten the small screws into the holes to

secure the back cover of the sensor onto

the mounted spacer.

6. Push the battery compartment case back

to the mounted spacer until it securely

clicks into place.

General product care

Taking care of your sensor

Your sensor contains sophisticated electronic

parts, so it must be treated with care.

Avoid rough treatment

Place the sensor down gently. Save the original

packing materials to protect your sensor if you

ever need to ship it.

Avoid water

Your sensor can be damaged if it gets wet.

Do not use the sensor outdoors in the rain,

or handle it with wet hands. Do not install the

sensor near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your sensor

Your sensor has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Storage

When you are not going to use the sensor for

some time, remove the battery from the sensor.

Store the sensor in a cool and dry place.

Frequently asked questions

Below are the questions most frequently asked about

the sensor. If you cannot ﬁnd the answer to your

question, call 1300 369 193 for customer service.

The display

shows

Open/Closed

X Low battery.

Press and hold CANCEL on the

handset to erase the message.

Replace the batteries with new

ones.

The sensor

does not work

at all.

Make sure two AAA batteries

are installed.

Check if the desired sensor is

on the sensor list. If the desired

sensor is not found, then it

may be deregistered from the

telephone base. Register the

sensor again.

The sensor may be out of range.

Move the sensor closer to the

telephone base.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to reduce

the risk of ﬁre, electric shock and injury, including

the following:

1. Adult setup is required.

2. Do not use this product near water. For

example, do not use it next to a bath tub, wash

bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

3. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

4. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over a

radiator or heat register.

5. Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

6. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

7. Periodically examine all components for

damage.

8. Children should be supervised to ensure that

they do not play with the product.

9. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance by

a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion if a

wrong type of battery is used for the sensor unit.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order not to

create a short circuit with conductive materials.

Customer service & product warranty

Please retain this booklet with your sales receipt as

proof of the date of purchase.

Customer Service

If you require assistance in operating this product,

please call the TecHelp Information Line on 1300 369

193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com.

Voluntary Product Warranty

In addition to your Statutory Rights and subject to the

conditions below, VTech warrants that this product will

be free from any defect in materials or workmanship

under conditions of normal use for a period of 12

months from date of purchase.

VTech does not warrant that the product will be free

from defects if defects are caused by an accident,

misuse, abuse, improper installation or operation,

vermin infestations, lack of reasonable care,

unauthorised modiﬁcation, loss of parts, tampering

or attempted repair by a person not authorised by

VTech; or where the product has been damaged by

lightning or a mains power surge.To make a claim

under this Voluntary Product Warranty you must call

the TecHelp Information Line on

1300 369 193 or contact VTech by e-mail at:

tcpsupport_au@vtech.com where a Customer

Service Representative will inform you of the product

return process. You will need to ensure that:

• You provide proof of purchase;

• Your product is suitably packaged (original

packaging is not required); and

• You have included all components from the original

purchase.

For your records

Date of purchase:

Place of purchase:

Serial number:

For Voluntary Product Warranty purposes, proof of

purchase is required so please keep your receipt.

The beneﬁts conferred by this Voluntary Product

Warranty are in addition to other rights and remedies

that are available to you under law, which cannot be

excluded. The processes for this Voluntary Product

Warranty in no way limit your rights which arise as a

result of your Statutory Rights.

This Voluntary Product Warranty is given by:

VTech Telecommunications (Australia) Pty Ltd ABN

70 136 672 627

Address: 24 Gilby Road, Mount Waverley 3149

IMPORTANT NOTE: THIS IS NOT A PRODUCT

RETURN OR SERVICE ADDRESS – PLEASE

CONTACT TECHELP BY PHONE OR EMAIL FOR

PRODUCT AND WARRANTY SUPPORT. NO

LIABILITY WILL BE ACCEPTED BY VTECH FOR

PRODUCTS RETURNED TO THIS ADDRESS

UNDER THIS VOLUNTARY PRODUCT WARRANTY.

Phone number: 1300 369 193

Email address: tcpsupport_au@vtech.com

Statutory Rights

Our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail

to be of acceptable quality and the failure does not

amount to a major failure.

Technical specifications

Frequency control Crystal controlled PLL

synthesizer

Transmit frequency 1881.792 - 1897.344 MHz

Channels 10

Sensor operating

temperature

-18°C (0°F) to 55°C (130°F)

Nominal effective

range

Actual operating range

may vary according to

environment conditions at

the time of use.

Power

requirements

2 x AAA batteries

Disclaimer

This product is not designed for security purposes.

When properly installed and maintained, this

product may in some cases reduce the risk of

burglary, ﬁre, robbery or other events occurring

without providing an alarm. VTech is not

responsible for losses, injury, or damage resulting

from the use of this product.

Vtech Telecommunications (Australia) Pty Ltd.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Specifications are subject to change without notice.

With spacer

Mount the sensor unit

Without spacer

With spacer

Without spacer

Mount the magnet unit

Table of contents

Other V-tech Accessories manuals

V-tech

V-tech CTM-S2116 User manual

V-tech

V-tech ErisTerminal VDP800 User manual

V-tech

V-tech VSMART VS013 User manual

V-tech

V-tech SN7021 User manual

V-tech

V-tech VC7151-302A User manual

V-tech

V-tech VDP650 User manual

V-tech

V-tech IS7121 User manual

V-tech

V-tech VC7151-102A User manual

Popular Accessories manuals by other brands

WhereNet

WhereNet LOS-4100 installation guide

ADT

ADT Pulse DBC835 Quick installation guide

Waeco

Waeco MF-40 instruction manual

Bulldog Security

Bulldog Security 791P operating manual

ESCALADE

ESCALADE Silverback B5400 owner's manual

Voltex

Voltex VMS-2 installation guide

Aroma Quest

Aroma Quest AQ-L25 instruction manual

tomado

tomado TEB1502W instruction manual

AEM

AEM 30-2226 instruction manual

Kasanova

Kasanova BELL'ARIA MAS020947 instruction manual

TESTO

TESTO 0638.1445 Handling instructions

pdlux

pdlux PD-LED2045-D instructions

Oakley

Oakley AIRWAVE 1.5 owner's manual

Stahl

Stahl 7571/11 Series operating instructions

Balluff

Balluff BML-S2C0-Q Series user guide

SICK

SICK LFV 200 operating instructions

Palram

Palram Sierra 2.3x2.3 Assembly instructions

SENSECAP

SENSECAP S210 Series user guide

V-tech VSMART VS001 User manual

Popular Accessories manuals by other brands