V-tech Push & Ride Alphabet Train User manual

91-003052-001
© 2015 VTech
Printed in China
Push & Ride Alphabet Train
User’s Manual

3
Introduction
INTRODUCTION
Thank you for purchasing the VTech®Push & Ride Alphabet Train
learning toy!
The VTech®Push & Ride Alphabet Train will take your child on a
journey through phonics, letters, numbers, music and more! Entertaining
sound effects, dancing lights and fun melodies reward your child’s
curiosity while taking baby on the ride of a lifetime!
VOLUME CONTROL
SWITCH
BOOK PAGE
ON/OFF/MODE
SELECTOR SWITCH
NUMBER
BUTTONS
LIGHT-UP
BUTTONS
LIGHT-UP SUN
BUTTON
WALKIE
TALKIE
BLOCK CHUTE
BLOCKS
BLOCK
RECOGNITION SLOT

4
INCLUDED IN THIS PACKAGE
• One user’s manual
Included In This Package
One engine
Four engine wheels and
four axel covers
One carriage bottom
One engine handle One walkie talkie and
walkie talkie holder
Two sheets of labels
Four carriage wheels
with axel trees
One carriage seat
with back support
One soft hinge
One carriage
front support
13 double sided
letter blocks

5
WARNING: All packing materials, such as tape, plastic sheets,
packaging locks and tags are not part of this toy,
and should be discarded for your child’s safety.
NOTE: Please keep user’s manual as it contains
important information.
Please stick the labels to the engine securely as
indicted below:
Labels

6
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover below the walkie
talkie on the side of the engine. Use a
screwdriver to loosen the screw.
3. Install 3 new ‘AA’ (AM-3/LR6) batteries
following the diagram inside the battery
box. (The use of new alkaline batteries is
recommended for maximum performance.)
4. Replace the battery cover and tighten the
screw to secure.
BATTERY NOTICE
• Use new alkaline batteries for maximum performance.
• Use only batteries of the same or equivalent type as recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
• Do not dispose of batteries in fire.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
Getting Started

7
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate
that the battery contains more than the specied value of
mercury (Hg), cadmium (Cd) or lead (Pb) set out in Battery
Directive (2006/66/EC).
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product or
batteries responsibly.
For more information, please visit:
www.recycle-more.co.uk
www.recyclenow.com
ASSEMBLY INSTRUCTIONS
1. To assemble the engine wheels, insert
the axels into the sockets on the body of
the engine until you hear them click into
place. Insert the wheels onto the axels
until you hear them click into place. Once
you have installed the wheels, they cannot
be removed.
Assembly Instructions
With the VTech®Push & Ride Alphabet Train safety comes rst.
To ensure your child’s safety, adult assembly is required.

8
2. Insert the walkie talkie holder into the
the slot below the battery cover until you
hear it click into place. Once you have
installed the walkie talkie holder, it cannot
be removed.
3. Position the handle so that the curved part
of the handle faces the back of the engine.
Insert the handle into the hole on the top of
the engine. Push down on the handle until
you hear it click into place. Once you have
installed the handle, it cannot be removed.
4. Insert the seat font support piece into the
front of the carriage until you hear it click
into place. Next, insert the back support
with the seat into the back of the carriage
until you hear it click into place. Once you
have assembled the carriage, it cannot be
taken apart.
5. Position the soft hinge so that the large
hole is facing up. Insert the hinge into the
hole at the front of the carriage until you
hear it click into place. Once you have
attached the hinge to the carriage, it
cannot be taken apart.
Assembly Instructions

9
Product Features
6. Insert the carriage wheels with axels into
the bottom of the carriage until you hear
them click into place. Once you have
installed the carriage wheels, they cannot
be removed.
7. To attach the carriage to the engine,
insert the soft hinge into the slot on the
back of the engine. You will hear the soft
hinge click into position, which lets you
know the carriage is attached correctly.
8. To detach the carriage from the engine,
press and hold the blue button under the
bottom of the engine, pull the hinge out of
the slot.
WARNING: Not to be used by children over 36 months.
Insufcient strength. 20 Kilograms Max.
Regularly check for signs of wear or tear on the snap in or locking
devices. If damaged do not use until repaired or replaced. Only to
be used under the direct supervision of a competent adult.
PRODUCT FEATURES
1. ON/OFF/MODE SELECTOR SWITCH
To turn the unit ON, slide the ON/
OFF/MODE SELECTOR SWITCH to
the LEARNING MODE ( ) or the
TRAVEL MODE ( ) position. To turn
the unit off, slide the ON/OFF/MODE
SELECTOR SWITCH to the OFF ( )
position.

10
2. VOLUME CONTROL SWITCH
Slide the VOLUME CONTROL SWITCH
to the LOW VOLUME ( ) or HIGH
VOLUME ( ) position.
3. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech®Push & Ride Alphabet Train
will automatically power-down after approximately 30 seconds
without input. The unit can be turned on again by pressing any
button, opening the book, inserting a block into the slot or inserting
the walkie talkie.
ACTIVITIES
1. Slide the on/off/mode selector switch
to choose a mode of play. You will hear
a song, a playful sound and a phrase in
both modes. The lights will ash with the
sounds.
2. Place the blocks into the block
recognition slot to learn letters and
objects in both modes. The lights will
ash with the sounds.
3. Press the number buttons to learn
numbers in the learning mode and learn
animals in the travel mode. Insert the
walkie talkie into the slot to hear fun
phrases to encourage imaginative play.
The lights will ash with the sounds.
Activities