VABCHES D3M531BS03 User manual

1-28
D3M531BS03
D3M531HZ03
As this item contains many parts, please read the installation
instruction carefully before installation . Please use tools
properly and carefully. If you have any questions about the
product and installation, please contact us.
Our professional after-sales team will serve you online all
[e-mail]
day.

Before You Start
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware of to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw. （Assembly
speed can be increased by using electric screwdriver）
Helpful Hints
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with an R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- If there is a back panel in the package, please install it to make sure your unit is
complete and sturdy.
-Please fix all the screws provided for the back panel which can enhance product
stability. If it is difficult to fix it when tightening, it can be fixed with the help of a
hammer and then tightened.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
PEOPLE NEEDED FOR ASSEMBLY: 1-2
2-28

Board Identification
Not actual size
TOP
Qty:1
A
RIGHT SIDE PANEL
Qty:1
C
LEFT SIDE PANEL
Qty:1
3-28
B
MIDDLE PANEL
Qty:1
D
REAR CROSS MEMBER
Qty:1
F
FRONT CROSS MEMBER
Qty:1
E
REAR LOWER PANEL
Qty:1
G
FIXED SHELF
Qty:1
I
DRESSING MIRROR
Qty:1
H

Board Identification
Not actual size
BACK PANEL
Qty:1
J
RIGHT DRAWER FRONT
Qty:1
L
LEFT DRAWER FRONT
Qty:1
4-28
K
LEFT DRAWER SIDE
Qty:2
M
DRAWER BACK
Qty:2
O
RIGHT DRAWER SIDE
Qty:2
N
DRAWER BOTTOM
Qty:2
P
LOWER LEFT FRAME
Qty:1
R
STOOL PANEL
Qty:1
Q

Board Identification
Not actual size
LOWER RIGHT FRAME
Qty:1
S
UPPER RIGHT FRAME
Qty:1
U
UPPER LEFT FRAME
Qty:1
5-28
T
RAIL
Qty:2
V
RAIL
Qty:1
X
RAIL
Qty:1
W
SIDE FRAME OF STOOL
Qty:2
Y
RAIL
Qty:2
Z
RAIL
Qty:1
AA

Not actual size
Board Identification
6-28
H
A
V
V
T
U
I
J
F
E
B
C
D
G
R
S
W
X
P
O
L
M
N
K
P
M
N
O
Q
Y
Y
Z
AA

Part List
15X9.5mm
1
CAM LOCK
spare:2
X16
7-28
∅6.5X35mm
2
CAM BOLT
spare:2
X16
∅6X30mm
3
WOOD DOWEL
spare:3
X28
∅6.3X50mm
4
SCREW
X4
5
SCREW
spare:2
X13
Ø3.5*14mm
6
SCREW
spare:3
X24
Ø3*14mm
7
SCREW
spare:2
X19
M6X12mm
8
SCREW
spare:2
X16
M6X30mm
9
SCREW
spare:2
X14
∅4X35mm
10
SCREW
X3
M4*18mm
12
SCREW
X4
131*13*21mm
13
HANDLE
X2
20*20*16mm
14
FIXED METAL PLATE
X4 15
LIGHT BULB
X1set
4*65mm
16
HEX KEY
X1
M6X35mm
11
SCREW
spare:2
X10
M6X40mm

8-28
17CL
LEFT CABINET MEMBER
X2
14"
17CR
RLGHT CABINET MEMBER
X2
LEFT DRAWER RUNNER
X2
RLGHT DRAWER RUNMER
X2
TIPPING RESTRAINT
HARDWARE KIT
X1 set
14"
17DL
14"
17DR
14"
Part List
18
350mm 350mm
19
SCREW
spare:1
X2
Ø4X14mm
20
SCREW
spare:1
X2
∅3X12mm
21
SOCKET
X1
22
HAIR DRYER RACK
X1
Insert the cam bolt into the hole first, then insert the cam lock and lock it.
13 24
Cam Lock Fastening System
The opening must point toward the
edge of the board

X1
STEP1
9-28
17CL X1 17CR X6 6
B
C
14" 14"
350mm 350mm Ø3.5X14mm
6
6
6
6
6
6
17CL
LEFT CABINET MEMBER
RLGHT CABINET MEMBER
17CR
UP
UP

STEP2
10-28
X1
17CL X1 17CR X6 6
14" 14"
350mm 350mm Ø3.5X14mm
6
6
6
RLGHT CABINET MEMBER
17CR
6
6
6
17CL
LEFT CABINET MEMBER
D
D
FLIP OVER
UP
UP

STEP3
11-28
X8
3
Ø6X30mm
2
3
D
B C
X4
2
Ø6.5X35mm

X2
STEP4
12-28
2X8 3X2 5
2
3
E
F
F
E
D
5
Ø6.5X35mm Ø6X30mm Ø4X35mm
Finished edge

STEP5
13-28
X4 X6
1 2
Proper orientation of CAM LOCK
UNLOCK
LOCK
A
F
E
D
C
B
1
2
Ø6.5X35mmØ15X9.5mm

STEP6
14-28
X6
1
Proper orientation of CAM LOCK
UNLOCK
LOCK
A
B
C
DE
1
3
X2
3
G
Ø15X9.5mm Ø6X30mm

X4 X4 X2
STEP7
15-28
4 8 11 X1 16
M6X40mm
Ø6.3X50mm M6X12mm
W
G
X
R
S
11
48
4X65mm
M6X40mm
Before you install this screw, please
make sure the screw size is M6*40mm
M6X12mm
Before you install this screw, please
make sure the screw size is M6*12mm
Please tighten the screws
to 80% first, and tighten
all screws 100% after all
parts are assembled.

STEP8
16-28
X2 X3 X1
1 10 16
M6X35mm
A
C
G1
10
S
R
X
Proper orientation of CAM LOCK
UNLOCK
LOCK
15X9.5mm 4X65mm
Before you install this screw, please
make sure the screw size is M6*35mm
M6X35mm
Please tighten the screws
to 80% first, and tighten
all screws 100% after all
parts are assembled.

STEP9
17-28
X2
3
H3
X4
14 X4 8X1 16
M6X12mm
X3
5
8
14
5
H
I
20X20X16mm Ø6X30mm 4X65mm
Before you install this screw, please
make sure the screw size is M6*12mm
M6X12mm

STEP10
18-28
X4
8X4 11 X1 16
M6X40mm
M6X12mm
11
8
H
H
I
I
T
U
T
V
V
4X65mm
Before you install this screw, please
make sure the screw size is M6*40mm
M6X40mm
Before you install this screw, please
make sure the screw size is M6*12mm
M6X12mm
Please tighten the screws
to 80% first, and tighten
all screws 100% after all
parts are assembled.

STEP11
19-28
X1
16
X8
9
H
A
G
S
M6X30mm
9
9
4X65mm
Before you install this screw, please
make sure the screw size is M6*30mm
M6X30mm
Before you install this screw, please
make sure the screw size is M6*30mm
M6X30mm
You can install the hair dryer rack(22) on
the left or right according to your needs
X2
19
Ø4X14mm
X1
22
19 22
Please tighten the screws
to 80% first, and tighten
all screws 100% after all
parts are assembled.

X19
7
STEP12
20-28
Ø3X14mm
7
J
X1 set
18
Ø3.5X14mm
Ø3.5*14mm
Make sure the holes in the middle row of the back
panel are aligned with the holes in the back of the
top panel, lock the screws in the middle row, and
finally lock others.
J