VacPak-It 186WM12 User manual

#186WM12
12" Single Roll
115V • 725W
#186WM18
18" Single Roll
115V • 750W 06/2021
Film Wrapping Machines

When using electrical appliances, basic safety should always be followed:
1. Read all instrucons before operang, cleaning or servicing this wrapping staon.
2. To protect against risk of electrical shock, do not place cord, plug or base in water or
other liquids.
3. Do not use outdoors.
4. Close supervision is necessary when any appliance is used near children.
5. The wrapping staon must be placed on a steady table.
6. Unplug the wrapping staon when not in use and before cleaning or servicing.
7. Avoid contact with moving parts.
8. Do not operate wrapping staon if it has malfunconed or has been dropped or dam-
aged. Call our toll-free customer support service number for informaon or examina-
on of a faulty unit that may require repair or an adjustment.
9. Do not operate wrapping staon if power cord or plug shows evidence of damage.
10. Do not operate if Hot Plate or Cut O Bar temperatures exceed 340°F, or if smoke is
detected.
11. Be aware of power cord locaon. Do not let cord rest on or touch hot surfaces. Do
not allow cord to hang freely over table or counter.
12. Keep body parts and clothing away from heang elements.
13. Do not touch or operate switches or cords with wet hands.
14. Do not place or store combusbles on or near the wrapping staon.
15. Insure that the plug has good ground connecon.
16. When unplugging wrapping staon, pull on the plug. Do not pull on the cord.
17. This wrapping staon was designed for commercial use only.
1
Important Safeguards ......................................1-2
Wrapping Stations ...........................................2
Replacement Parts ..........................................3
Operating Instructions .......................................3
Film Loading Diagram........................................3
Cleaning the Unit............................................4
Servicing the Unit ...........................................4
Fuse Replacement...........................................4
Wiring Diagram .............................................5
Model Specifications.........................................5
Warranty ...................................................6
table of contents
important safeguards
save these instructions

Caution
• Hot Surfaces - Avoid Contact!
• To provide connued protecon against electric shock, connect only to properly grounded
outlets.
• Do not aempt to repair or replace any parts other than the replacement parts listed in these
instrucons. Improper repair or replacement may result in electrical hazards.
• Do not aempt to repair or replace any parts other than the replacement parts listed in these
instrucons. Improper repair or replacement may result in electrical hazards and will void the
warranty.
2
wrapping stations
186WM12, 186WM18
CUT OFF ROD
INDICATOR LIGHT
(BEHIND SIDE SPLASH)
HOT PLATE
ASSEMBLY
TEFLON® COVER
THERMOSTAT KNOB
COVER PLATE
FILM ROLL
BEARING BLOCK
WING NUT
PLASTIC CAPS
FILM ROLL BAR
POWER CORD
(UNDERNEATH
COVER PLATE) ON/OFF SWITCH
(UNDERNEATH
COVER PLATE)

This appliance is designed for wrapping fruits, vegetables, sh, meat, cold food, etc.
1. To load lm onto lm rod, place lm roll onto lm roll bearing blocks, ghten the wing nuts
and put the plasc caps onto threaded ends.
2. Flip cover plate upward.
3. Route the lm between cover plate and lm retainer rod. (See Film Loading Diagram)
4. Insert the power cord plug into a properly grounded outlet.
5. Turn the main switch on and the red indicator lamp will light up.
6. Flip cover plate downward to original posion.
7. Turn the thermostat to set the desired temperature.
8. Allow 5-10 minutes for the unit to pre-heat.
9. Place food onto the cover plate.
10. Draw out the lm and cover the package, tucking several inches of lm underneath. Pull the
package toward you to completely enclose it in lm.
11. Use the Cut O Bar to cut lm.
12. Place wrapped package onto hot plate for 3-5 seconds to seal.
REPLACEMENTS PARTS
Operating instructions
film loading diagram
Item Number Description
PWM18212 Fuse - 1A, 250V
PWM1824 Cut O Rod
PWM5901 Teflon® Cover
PWM6101 Hot Plate Assembly
CUT OFF ROD
COVER PLATE
PLASTIC CAPS
WING NUTS
FILM ROLL
BEARING BLOCK
FILM ROLL
FILM
CONTROL BOX
FILM RETAINER
ROD
HOT PLATE
3

• Unplug the wrapping staon before cleaning and/or servicing.
• When Cut O Bar and/or hot plate becomes dirty, clean with a coon cloth. Do not use metal
or other abrasives. Do not immerse the wrapping staon in water or other liquids.
• Do not spray cleaners or liquids onto any electrical components.
• This wrapping staon should only be serviced by trained personnel.
• Unplug the wrapping staon before servicing.
• Do not aempt to repair or replace any parts other than the replacement parts listed in these
instrucons. Improper repair or replacement may result in electrical hazards and will void the
warranty.
1. Unplug the wrapping staon before servicing.
2. Situate the wrapping staon on a stable surface so that the back of wrapping staon
is accessible.
3. Turn the fuse holder cap counterclockwise to loosen unl it is released from the fuse
holder receptacle. The fuse will be aached to the cap.
4. Remove the fuse from the fuse holder cap by pulling gently.
5. Replace fuse with only type 1A (part PWM18212).
6. Insert new fuse into fuse holder cap.
7. Insert fuse holder cap with fuse into the fuse cap receptacle.
8. Turn the fuse holder cap clockwise to ghten unl it is hand ght.
9. Situate the wrapping staon into normal operang posion on a stable surface.
10. Plug the wrapping staon into a properly grounded outlet.
Noble Chemical’s Strike all purpose cleaner and degreaser makes it easy to keep your kitchen clean.
Aack tough grease, oil, and carbon with this ready-to-use cleaner and degreaser. Its unique formula
is designed to clean concrete, machinery, engines, oors, walls and more!
CLEANING THE UNIT
servicing THE UNIT
fuse replacement
4

Cut O Rod
Model 186WM12 186WM18
Dimensions 15⁄"W x 21"D x 5"H 22"W x 26"D x 5"H
Amps 6.5 6.5
Hertz 60 60
Capacity 1 Roll 1 Roll
Voltage 115V 115V
Wattage 725W 750W
Plate Material Teflon®-Coated Teflon®-Coated
Maximum Roll Length 12" 18"
wiring diagram
model specifications
5

6
EQUIPMENT LIMITED WARRANTY
To Make a Warranty Claim:
For Warranty Inquiries contact the location where you purchased the product:
• WebstaurantStore.com: Contact [email protected]. Please have your order number ready.
• The Restaurant Store: If you purchased this unit from your local store, please contact your store directly.
• TheRestaurantStore.com: Online purchases, call 717-392-7261. Please have your order number ready.
Failure to contact the designated location prior to obtaining equipment service may void your warranty.
VacPak-It makes no other warranties, express or implied, statutory or otherwise, and HEREBY DISCLAIMS ALL
IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A
PARTICULAR PURPOSE.
This Limited Warranty does not cover:
• Equipment sold or used outside the Continental United States
• Use of unfiltered water (if applicable)
• VacPak-It has the sole discretion on wearable parts not covered under warranty
• Equipment not purchased directly from an authorized dealer
• Equipment used for residential or other non-commercial purposes
• Equipment that has been altered, modified, or repaired by anyone other than an authorized service agency
• Equipment where the serial number plate has been removed or altered.
• Damage or failure due to improper installation, improper utility connection or supply, and issues resulting from
improper ventilation or airflow.
• Defects and damage due to improper maintenance, wear and tear, misuse, abuse, vandalism, or Act of God.
Any action for breach of this warranty must be commenced within 1 year of the date on which the breach occurred.
No modification of this warranty, or waiver of its terms, shall be eective unless approved in a writing signed by the
parties. The laws of the Commonwealth of Pennsylvania shall govern this warranty and the parties’ rights and duties
under it. VacPak-It shall not under any circumstances be liable for incidental or consequential damages of any kind,
including but not limited to loss of profits.
VacPak-It warrants its equipment to be free from defects in material and workmanship for a period of 1 year. This is the sole
and exclusive warranty made by VacPak-It covering your VacPak-It brand equipment. A claim under this warranty must be
made within 1 year from the date of purchase of the equipment. Only the equipment’s original purchaser may make a claim
under this warranty. VacPak-It reserves the right to approve or deny the repair or replacement of any part or repair request.
The warranty is not transferable. VacPak-It Equipment installed in/on a food truck or trailer will be limited to a period of 30
days from the original date of purchase.