VADO synergie Installation and operating instructions

Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[e-mail]
www.vado-uk.com
guarantee
customer/technical services
For any technical or installation queries please contact Vado on 01934 745163.
GUARANTEE REGISTRATION
NAME
ADDRESS
RETAILER
ADDRESS
PURCHASE DATE
PRODUCT DESCRIPTION
WHO INSTALLED THE PRODUCT?
FOR VADO USE
POSTCODE
POSTCODE
ARTICLE NUMBER (SEE BOX)
RETAILER PLUMBER BUILDER SELF
This product is guaranteed against manufacturing defects from the date of purchase until the expiry of the relevant
guarantee period shown below.
The guarantee is only valid if:-
1. The product has been installed, used and maintained in accordance with Vado’s instructions and subjected to
normal use only.
2. The defect is not due to use of an unsuitable or inadequate water or power supply.
3. The defect is not due to accident, misuse, neglect or repair other than by Vado or Vado authorised agents or
damage caused by foreign objects or substances.
4. We have received from you the completed Guarantee Registration Form. Vado accepts no responsibility for any
forms lost in the post and returns by registered means is therefore recommended.
Under this guarantee (which is non-transferable) Vado will, at its option, repair or replace free of charge any product
(or replacement part) found to be defective. The guarantee does not extend to any consequential loss or damage.
After repair or replacement the relevant guarantee period will be calculated from the original date of purchase.
The relevant guarantee periods are:-
1. Twelve years on chrome nish products.
2. Three years on all other products with the exception of Stuart Turner Pumps which carry a 2 year Guarantee on
Monsoon Range and 1 Year Guarantee on Showermate Range.
All claims under the guarantee must be submitted in writing to the person who supplied the product to you and
must be received no later than the last day of the relevant guarantee period. All claims must be accompanied by
proof of purchase (sales receipt or delivery note).
Vado operates a policy of continuous product development and therefore reserves the right to change the product,
packaging and documentation specications without notice.
This guarantee is in addition to and does not aect your statutory rights as a consumer.
installation & maintenance instructions
mono bidet mixer
please leave these instructions with the customer
synergie
Syn 110.indd 1 10/2/10 11:03:13

important - please read
general installation
27
installers/users notes
Please read these instructions carefully before starting installation and keep for future
reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and ttings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing (UK:BS6700) Regulations.
We strongly recommend that you use a qualied and registered plumber.
These ttings are mixing devices and therefore water supplies must be reasonably
balanced.
Where connections are made to the mains cold water supply, WRC approved single
check valves must be tted to both hot and cold inlets. This is a stated requirement of
Water Supply (Water Fittings) Regulations 1999 Schedule 2, Section 6 G15.13.2
Before making any inlet pipe connections, all supply pipes MUST be thoroughly
ushed to remove debris. Failure to do so could result in damage or low ow from the
mixer unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 4 G13.1
The tting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
care of the mixer
Our products are nished to the highest standard and due care needs to be taken to
ensure their looks are retained.
We recommend cleaning all products with a soft damp cloth ONLY and advise strongly
against the use of ALL cleaning products i.e. powders and liquids.
If the above instructions are not followed this will invalidate your guarantee in the
event of a problem occurring.
Syn 110.indd 2 10/2/10 11:03:13

6
dimensions
3
Operating Specications
operation
Operating Pressure:
Minimum operating pressure 0.5 bar
Maximum operating pressure 5 bar
Moving the mixer lever forwards will actuate the ow of water and progressively
increase the water temperature.
69mm
2 x G1/2”
65mm
116mm
43mm
max 180 mm
88.7mm
max 50mm
125mm
max 40mm
88mm
70mm
25mm
63mm
41mm
109mm
5° - 15°
G 1-1/4”
6mm
44-45mm
38mm
Pull the vertical control
rod up to close the
waste outlet and push
down to open.
Syn 110.indd 3 10/2/10 11:03:14

installation
45
pop-up waste assembly and installation
Insert the vertical control rod through
the hole in the back of the mixer body.
Dissemble the pop-up waste and
reassemble onto the basin.
Unscrew the ball joint retainer on the
side opening of the pop-up waste. Insert
the short end of the horizontal control
rod (with ball joint) into the waste and
clamp in position by retting the ball
joint retainer. Do not over tighten.
Slide the control rod link onto the
horizontal control rod and vertical
control rod and loosely tighten.
Test the action of the pop-up waste and
fully tighten the rod link. Adjust the ball
joint retainer as required.
Turn on the water supply and turn the
mixer on fully to ush through any
possible debris from the mixer. Finally
check all new connections for leaks.
Before installing your new mixer, ush
through the pipework to ensure removal
of debris, turn o the water supply.
Make sure that the mixer seal is in
position against the mixer body.
Position the mixer on the basin. From
the underside of the basin t the rubber
washer onto the threaded rod followed
by the metal washer and the locking
ring. Screw the locking ring up until
the bolts touch the washer. Tighten the
locking bolts (2) to clamp the mixer to
the basin.
CAUTION: Do not over tighten the bolts
as this may damage the basin.
Screw the two exible pipes to the hot
and cold connections on the mixer
body, do not over tighten.
Connect the water supply to the
inlet pipes. The hot water should be
connected to the back pipe.
Mixer seal
Hot
connection
Cold
connection
Threaded rod
Rubber
washer
Metal
washer
Locking
bolts
Locking
ring
Flexible pipes
Control
handle
Vertical
control
rod
Horizontal
control rod
Ball joint
retainer
Control
rod link
Seal
Plug
Plug
housing
Seal
Syn 110.indd 4 10/2/10 11:03:16