VADO zoo sense Installation and operating instructions

zoo sense
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[email protected]
www.vado-uk.com
guarantee
customer/technical services
For any technical or installation queries please contact Vado on 01934 745163.
GUARANTEE REGISTRATION
NAME
ADDRESS
RETAILER
ADDRESS
PURCHASE DATE
PRODUCT DESCRIPTION
WHO INSTALLED THE PRODUCT?
FOR VADO USE
POSTCODE
POSTCODE
ARTICLE NUMBER (SEE BOX)
RETAILER PLUMBER BUILDER SELF
This product is guaranteed against manufacturing defects from the date of purchase until the expiry of the relevant
guarantee period shown below.
The guarantee is only valid if:-
1. The product has been installed, used and maintained in accordance with Vado’s instructions and subjected to
normal use only.
2. The defect is not due to use of an unsuitable or inadequate water or power supply.
3. The defect is not due to accident, misuse, neglect or repair other than by Vado or Vado authorised agents or
damage caused by foreign objects or substances.
4. We have received from you the completed Guarantee Registration Form. Vado accepts no responsibility for any
forms lost in the post and returns by registered means is therefore recommended.
Under this guarantee (which is non-transferable) Vado will, at its option, repair or replace free of charge any product
(or replacement part) found to be defective. The guarantee does not extend to any consequential loss or damage.
After repair or replacement the relevant guarantee period will be calculated from the original date of purchase.
The relevant guarantee periods are:-
1. Twelve years on chrome nish products.
2. Three years on all other products with the exception of Stuart Turner Pumps which carry a 2 year Guarantee on
Monsoon Range and 1 Year Guarantee on Showermate Range.
All claims under the guarantee must be submitted in writing to the person who supplied the product to you and
must be received no later than the last day of the relevant guarantee period. All claims must be accompanied by
proof of purchase (sales receipt or delivery note).
Vado operates a policy of continuous product development and therefore reserves the right to change the product,
packaging and documentation specications without notice.
This guarantee is in addition to and does not aect your statutory rights as a consumer.
5 hole deck mounted concealed bath shower mixer
installation & maintenance instructions
please leave these instructions with the customer

important - please read
general installation
27
operation
Please read these instructions carefully before starting installation and keep for future
reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and ttings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing (UK:BS6700) Regulations.
We strongly recommend that you use a qualied and registered plumber.
These ttings are mixing devices and therefore water supplies must be reasonably
balanced.
Where connections are made to the mains cold water supply, WRC approved single
check valves must be tted to both hot and cold inlets. This is a stated requirement of
Water Supply (Water Fittings) Regulations 1999 Schedule 2, Section 6 G15.13.2
Before making any inlet pipe connections, all supply pipes MUST be thoroughly
ushed to remove debris. Failure to do so could result in damage or low ow from the
mixer unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 4 G13.1
The tting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Hot tap - moving
the tap lever from
left to right will
increase the ow of
water.
Cold tap - moving the tap lever
from left to right will increase
the ow of water.
care of the taps
Our products are nished to the highest standard and due care needs to be taken to
ensure their looks are retained.
We recommend cleaning all products with a soft damp cloth ONLY and advise strongly
against the use of ALL cleaning products i.e. powders and liquids.
If the above instructions are not followed this will invalidate your guarantee in the
event of a problem occurring.
maintenance
ow straightener
aerator (tted)
The mixer is supplied with an aerator
tted as standard. To improve the ow
rate in low pressure conditions this
aerator can be changed for the plastic
ow straightener provided.
Carefully unscrew the mixer nozzle
taking great care not to damage the
plated nish.
Shower/spout lever - diverts
the ow of water to either the
shower or the spout.

6
dimensions
3
installation - spout and shower
Rubber
washer
Washer
Nut
Flexible pipe
Aerator
Adaptor
nut
Connecting
tube
Shower
hose
Cover
plate
Washer
Hand set
Position the spout in place , and from the
underside slide on the rubber washer,
metal washer and then the nut. Tighten
the nut to clamp on the spout.
CAUTION: Do not over tighten the nuts.
Connect the spout to the valve using
one of the exible pipes.
Rubber
washer
Washer
Nut
Screw the connecting tube into the
cover plate and position in the hole,
from the underside slide on the rubber
washer, metal washer and then the nut.
Tighten the nut to clamp on the spout.
CAUTION: Do not over tighten the nuts.
Place the rubber washer into the cone
end of the hose and screw to the
handset, thread the other end of the
shower hose down through the cover
plate and screw on the adaptor nut.
Connect the adaptor nut to the outlet
ports on the divertor valve.
240-300mm
3/4”
164mm
232mm
55mm
63mm
3/4”
3/4”
90mm
33mm33mm
28mm
Operating Specications
Minimum operating pressure 0.7 bar
3/4”
67mm
1/2”
49-64mm
45mm
Diverter
3/4”

4
installation - diverter valve
5
installation - tap
Rubber
washer
Nut
Control
handle
Washer
Cover
Rubber
washer
Washer
Nut
Valve
Flexible pipe
to diverter
valve
Before installing your new tap, ush
through the pipework to ensure removal
of debris, turn o the water supply.
Screw a nut onto the valve body fol-
lowed by metal washer then a rubber
washer, push the valve up through the
hole in the basin making sure the inlet
hole is pointing in the right direction.
Slide on a rubber washer, metal washer
and then a nut. Tighten the nut to clamp
the valve to the basin.
The position of the valve can be adjusted
by repositioning the backnut and then
tightening the front.
Screw on the cover.
Carefully push the control handle onto
the splines of the valve and secure
with the grub screw using the supplied
hexagonal key, replace the screw cover.
CAUTION: Do not over tighten the nuts
as this might damage the basin.
Connect the water supply to the inlet
pipes. The hot water should be con-
nected to the left hand pipe.
Hot/cold
inlet
Grub
screw
Control
handle
Cover
Rubber
washer
Nut
Valve
Screw the nut onto the valve body
followed by a rubber washer, push the
valve up through the hole in the unit.
Screw on the cover, carefully push the
control handle onto the splines of the
valve and secure using the hexagonal
screw, plug in the rubber cover.
From the underside tighten the nut to
secure the valve in place.
CAUTION: Do not over tighten the nuts
as this might damage the unit.
Connect the valve to the tap, shower
and spout using the exible connectors.
Flexible pipe
outlet to
spout
Flexible pipe
inlet from
hot tap
Shower hose
outlet to
shower head
Cover
plug
Hexagonal
screw
Flexible pipe
inlet from
cold tap