Vaillant timeSWITCH 140 Specification sheet

timeSWITCH 140
GB, ES, PT, TR
Erklärung der Zeichenformate
[changed] oder [c] [/c] =

For the owner and heating engineer
Operating and installation manual
timeSWITCH 140
GB
Two-channel timer with week programme

2
Contents
Contents
1 Notes on the documentation. . . 4
1.1 Storage of the documents........... 4
1.2 Symbols used.................................. 5
1.3 Applicability of the manual ......... 5
Operating manual. . . . . . . . . . . . . . . . 6
2 Overview of the device . . . . . . . 6
2.1 Intended use.................................... 6
2.2 Safety................................................ 7
2.3 Overview of the control
elements........................................... 8
2.4 Overview of the display................ 9
3 Operation. . . . . . . . . . . . . . . . . . . 10
3.1 Setting the current day of the
week and the time......................... 10
3.2 Default setting................................ 10
3.4 Setting the operating modes...... 16
3.5 Special functions............................ 16
3.6 Calendar........................................... 19
4 Information button. . . . . . . . . . . 19
5 Recycling and disposal. . . . . . . .20
Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_02

3Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
Contents
GB
Installation manual . . . . . . . . . . . . . . 21
6 Installation instructions . . . . . . 21
6.1 Notes on the installation and
operation.......................................... 21
6.2 CE label............................................. 21
6.3 Intended use.................................... 21
7 Safety instructions and
regulations . . . . . . . . . . . . . . . . .22
7.1 Safety instructions ........................ 23
7.2 Regulations...................................... 23
8 Installation . . . . . . . . . . . . . . . . .23
9 Start-up. . . . . . . . . . . . . . . . . . . .25
9.1 Installer level (calendar) .............. 25
9.2 Service/diagnostics level............. 27
10 Handing over to the owner . . . .28
11 Customer service and
warranty . . . . . . . . . . . . . . . . . . .29
12 Technical data . . . . . . . . . . . . . .29

1 Notes on the documentation
1 Notes on the documen-
tation
The following notes are intended to help
you throughout the entire documentation.
Further documents apply in combination
with this installation and operation manual.
We accept no liability for any damage
caused by failure to observe these
manuals.
Other applicable documents
Operating, installation and assembly
manuals for all system components
1.1 Storage of the documents
Please pass on this operating and instal-
lation manual to the owner of the sys-
tem so that he or she can keep it availa-
ble whenever it is required.
Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_024

5Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03 GB
Notes on the documentation 1
1.2 Symbols used
Please observe the safety instructions in
this manual.
The symbols used in the manual are
explained below:
Caution!
Potentially dangerous situations
for the product and environment!
Note!
Useful information and instruc-
tions
• Symbol for a required task
1.3 Applicability of the manual
This operating manual applies exclusive-
ly to units with the following article
numbers:
306760
The part number of your unit can be
obtained from the identification plate.

6Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
2 Overview of the device
Operating manual
2 Overview of the device
2.1 Intended use
The timeSWITCH 140 is a state-of-the-art
two-channel timer which has been
designed in accordance with approved
safety regulations. Nevertheless, there is
still a risk of injury or death to the user
or others or of damage to the device and
other property in the event of improper
use.
The timeSWITCH 140 timer is a two-
channel timer with a day and week
programme which is used to time control
a Vaillant boiler with or without hot water
supply.
If the device is used together with a
Vaillant combi boiler, it can take over the
programming of the warm start function
(control of the hot water release).
Any other use or extended use is consid-
ered to be improper. The manufacturer/
supplier is not liable for any resulting
damage. The heating engineer and/or
the owner alone bear the risk.
Intended use includes the observance of
the operating and installation manual.

7Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03 GB
Overview of the device 2
Caution!
Any improper use is forbidden!
2.2 Safety
The timer must be installed by a suitably
qualified heating engineer, who is
responsible for adhering to the relevant
standards and regulations.

8Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
2 Overview of the device
2.3 Overview of the control
elements
iFP
1
2
Fig. 2.1 Overview of the control elements
Key
1 Display
2 Dial (turn and click)
I Information button
F Special function button
P Programming/Calendar function button

9Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03 GB
Overview of the device 2
2.4 Overview of the display
1
2
3
5
6
4
10
8
9
7
Fig. 2.2 Overview of the display
Key
1 Programming of the timer programme
2 Installer and service/diagnostics level
3 Indicator that boiler is in operation
4 Information level
5 Hot water channel (heating request)
6 Heating channel (heating request)
7 Time
8 Days of the week
9 Operating modes
10 Special functions

10 Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
3 Operation
3 Operation
The heating and hot water channels
(only in the event of a heating or hot
water channel request during the pro-
grammed time), the current day of the
week, the current time and the special
function (if activated) are displayed on
the basic display.
3.1 Setting the current day of the
week and the time
The current time and the day of the
week are set on the basic display.
• Press the dial three times until the day
of the week flashes.
• Turn the dial to select the desired day.
• Press the dial again until the hour
display flashes.
• Turn the dial to select the current hour.
• Press the dial again until the minute
display flashes.
• Turn the dial to set the minutes.
The basic display reappears after about
five seconds.
3.2 Default setting
The timer is supplied with a basic pro-
gramme with default settings (table 3.1).
The heating and hot water control follow
this basic programme until it is changed.

11Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03 GB
Operation 3
Time
window
Day of the
week / Week
block
Start
time End time
H1 Mo–Fr 6:00 22:00
H2 - - -
H3 - - -
H1 Sa 7:00 23:00
H2 - - -
H3 - - -
H1 Su 7:00 23:00
H2 - - -
H3 - - -
Table 3.1 Heating/Hot water basic programme
3.3 Programming heating times
for heating and hot water
(warm start)
You can program three time profiles
(H1, H2 and H3) for each channel (heat-
ing or hot water):
– For individual days (Monday (Mo) to
Sunday (Su))
– For a group of days, e. g.
5 days (Monday (Mo) to Friday (Fr)),
2 days (Saturday (Sa) to Sunday (Su))
or 7 days (Monday (Mo) to Sunday (Su))

12 Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
3 Operation
Heating Mo Tu We Th Fr Sa Su
H1 Start
End
H2 Start
End
H3 Start
End
Hot water Mo Tu We Th Fr Sa Su
H1 Start
End
H2 Start
End
H3 Start
End
Table 3.2 Time profiles for heating and hot
water

13Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03 GB
Operation 3
Note!
To change the default settings of
the basic programme, you can
enter your personal time profiles
in this table.
The following steps are required to
change the basic programme:
• Press the programming button “P” to
go to the programming level.
The symbol P appears on the display and
the radiator symbol flashes.
• Turn the dial to select the desired
heating channel (radiator symbol) or
hot water channel (tap symbol).
• Press the dial again to select the time
profile (H1, H2 or H3).
The day(s) of the week, start time and
end time appear on the display.
The basic display reappears if you press
the “P” button again.
For clarification, the individual steps are
illustrated in the following table:

14 Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
3 Operation
Display Required steps
Press the program-
ming button “P”.
Turn the dial to select
the desired channel
(heating or hot water).
Press the dial.
The cursor marks the
time profile.
Press the dial to
select the desired
time window H1, H2
or H3.
Press the dial. The day
of the week display
flashes.
Turn the dial to select
one or various days.
You can select the
following:
– Individual days:
Mo = Monday
Tu = Tuesday
We = Wednesday
Th = Thursday
Fr = Friday
Sa = Saturday
Su = Sunday
– 5 days: (Mo – Fr)
– 2 days: (Sa – Su)
– 7 days: (Mo –Su)

15Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03 GB
Operation 3
Press the dial to
change the start time.
The hour display
flashes.
Turn the dial to select
an hour.
Press the dial again.
Turn the dial to select
the minutes.
Press the dial to
change the end time.
The hour display
flashes.
Turn the dial to select
an hour.
Press the dial again.
Turn the dial to select
the minutes.
Press the “P” button
to return to the basic
display.
Table 3.3 Setting parameters

16 Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
3 Operation
3.4 Setting the operating modes
The operating mode of the boiler is set
on the basic display.
• Press the dial once to select the
operating mode of the heating channel.
• Press the dial twice to select the oper-
ating mode of the hot water channel.
The current operating mode display
flashes.
• Turn the dial to select the desired
operating mode.
The basic display reappears after about
five seconds.
Possible operating modes
Automatic
The heating/hot water mode
switches between “Ready for
operation” and “Off” according
to the programmed times.
Heating
The heating/hot water mode
remains permanently set to
“Ready for operation”.
Off
The heating/hot water mode
remains permanently set to Off.
3.5 Special functions
• Press the “F” button to select special
functions (see table 3.4):

17Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03 GB
Operation 3
Display Required steps
Party function
Press the special func-
tion button “F” to set
the party function.
The timer programme
is consequently deacti-
vated temporarily.
Operation remains
switched on up to the
next time profile (H1
– H3), regardless of
whether the timer is
set to the “Ready for
operation” or “Off”
operating mode. The
timer programme is
then reactivated.
The basic display reap-
pears after about ten
seconds.
To deactivate the
party function, you
merely have to press
the “F” button.
The party function is
only available in auto-
matic operating mode
( ).

18 Operating and installation manual timeSWITCH 140 two-channel timer with week programme / 838312_03
3 Operation
Holiday function
Press the special func-
tion button “F” twice
to set the holiday
function.
Set the number of
days for which the tim-
er programme is to be
deactivated by turning
the dial.
Operation remains in
Off operating mode
until midnight of the
last set day day. The
timer programme is
then reactivated.
The basic display reap-
pears after about ten
seconds.
To deactivate the
holiday function, you
merely have to press
the “F” button.
Table 3.4 Special functions