VALCOBABY Tri Mode Series Installation and operation manual

Product Reference Guide
Read and follow the instructions contained within carefully before use. Retain this guide in a safe and
easily accessible place for future reference.
Drawings, pictures and specifications contained in this manual are for illustration purposes only – actual product may vary. VALCO BABY reserves the right
to alter any specification(s), colour or features without prior notice or incurring any obligation to similarly alter products previously purchased.
S E R I E S

Thank you for purchasing a quality VALCO product. Due to our policy of continuous product development, this
product is constantly evolving. It is possible that some features or procedures outlined here have changed since
this document was written. If you are unsure of any procedure outlined here please contact the store from which
you purchased it to obtain the most up to date information, or contact us via the internet. See relevant web contact
addresses on the back page.
Remove the stroller from the carton and dispose of all packaging immediately including the black rubber protectors on either side of the
brake bar and front wheel protector. The front wheel forks, rear wheels, front bar and hood all need to be installed prior to use.
IMPORTANT WARNING: Always test that all latches are securely engaged before use.
Stroller Assembl
y
/O
p
enin
g
1. Lay the stroller flat on the floor and
carefully cut the cable tie which
holds the frame.
2. Lift the handle upward to a vertical
position.
1. Lift the front wheel housing upward
so that the stroller frame unfolds
from beneath.
2. Press down on the locking hinge
with your hand or foot.
1. Secure the frame closed by
swinging the fold latches (located
on both sides of the frame) and
fully engaging them tightly onto
the frame.
Installin
g
/Removin
g
the rear wheels
1. To remove the wheel simply
press the axle button in the centre
of the wheel hub and
simultaneously pull the wheel
outward.
1. Pressing the axle button, insert the
protruding long axle into the
opening in the tube at the rear of the
stroller chassis.
2. Repeat this procedure for the other
side.
If your brakes do not engage, check to see that the nylon brake cogs are on the INSIDE of each wheel when it is
attached to the chassis. If not, remove the wheel and SQR axle and re-insert the SQR axle from the other side of the
wheel, so that the cog will be on the inside of the wheel.
1. Pressing on the centre hub button,
insert the SQR axle through the
outside of the metal hub in each
wheel.
IMPORTANT: Insert through outside of
the wheel - the side which does NOT
have the nylon brake cog)
Your front bar
1. Remove the plugs from the nylon housing at either side of the stroller frame by
pressing each inner “release button” and pulling the plug upward.
2. Insert the bar ends into the nylon housing located on either side of the frame. Be sure
that the bar is securely engaged
3. Adjust the front bar by simultaneously pressing the 2 red buttons and swivelling the
bar (forward or backward). NEVER use your stroller with the front bar in the lowest
position. This position is ONLY for use when folding the stroller!
4. To remove the front bar: Feeling the side of the nylon housing that sits below the
frame at each side (facing inward), locate the release “button.”
5. Press the release button inward while simultaneously pushing upward on the bar
housing. Repeat for the other side.
IMPORTANT WARNING: The front bar IS NOT a restraining device. ALWAYS re-insert the
plugs into the housing when there is nothing inserted.

Installin
g
/Removin
g
and usin
g
the front wheel forks
Your Runabout stroller utilizes our unique
and revolutionary new TRI-MODE™ front
swivel system:
1. To install the front fork, rotate the TRI-
MODE selection dial to the centre
(450) position.
2. Tilt the stroller frame upward on the
rear wheels.
3. Insert the fork shaft into the TRI-
MODE housing till it “clicks” into place.
IMPORTANT: Always test that the fork is
securely engaged in the housing.
Foldin
g
/O
p
enin
g
y
our stroller
1. To open, unhook the frame
locking strap reversing the
previous step.
To remove the front fork:
1. Rotate the TRI-MODE selection
dial to the centre (450) position.
2. Tilt the stroller frame upward on
the rear wheels.
3. Press the centre release button.
The fork will then be released.
The unique TRI-MODE™ swivel system is as
flexible as it is functional over a variety of
terrains and uses.
1. LOCK: This position is best for use on
extremely rough or soft terrain such as
sand etc which inhibit wheel swivel. To lock
your wheel, rotate the dial to the “LOCK”
position. Swivel the wheel around till it
locks into position.
2. O: The central position locks the wheel into
a tight 450 swivel arc. This provides more
stability for use with a toddlerseat or when
going down inclines.
3. SWIVEL: This position allows full,
unfettered swivel action.
3. Simultaneously lift the secondary
safety catch and swing the handle
forward.
4. Holding the frame at the rear,
press down with your foot on the
rear basket tube. This will
disengage the side hinge locks.
5. Continue pushing the rear of the
basket, moving the rear wheels
forward beneath the frame.
1. Fold the hood back up against the
handle.
2. Release the locking clamps at either
side of the stroller.
2. Holding on to the side of the
footrest, with your foot stopping
the rear wheels, lift the handle so
that the frame begins to unfold.
6. You can lock the frame closed by
stretching the locking strap over the
frame, placing the metal catch over
the rivet on the chassis

Your seat can be adjusted to 4 positions
using the zip system
1. To recline, pull one of the zippers
located on the seat side downward.
2. Do the same to the corresponding zipper
on the other side of the seat
3. For more recline, release more zippered
sections.
4. For seat incline simply reverse this
procedure.
BE SURE THAT ALL ZIPPERS ARE
OPENED/CLOSED FULLY BEFORE USE.
Ad
j
ustin
g
y
our seat
–
zi
p
/belt S
y
stem (selected units)
Installin
g
y
our hood
Usin
g
y
our brakes
1. Place the plastic hood housings over
the corresponding housing on either
side of the stroller frame.
2. Align the straight track on the stroller
housing with the corresponding “hole”
in the hood housing.
3. Slide the hood housing downward,
over the track, so that it completely
engages onto the stroller frame.
“no zi
p
” recline
(selected units)
The new “no zip” recline offers an
almost infinite amount of seat
adjustments:
1. RECLINE: While squeezing the centre
release mechanism in a pincer action,
ease the seat down to the desired
position.
2. INCLINE: Place your hand in the
centre of the rear of the seat.
3. Pull the incline strap while gently
pushing on the rear of the seat until
the desired position has been
reached. IMPORTANT: Always check
that the brake has fully
engaged
ALWAYS TEST that the seat is securely
locked in place.
3. Press down on the side locking
hinges (on the basket) to lock the
frame in the open position.
4. Secure the handle to the frame by
engaging the locking clamps on
both sides.
In addition to the 4 adjustment
positions using the zip system, your
stroller has an additional 5th position
which raises the seat to an even more
upright sitting position.
1. With all zippers fully closed, lift
the seat back further upward with
your hand.
2. Secure the seat with the two sets
of straps (one at the top and one
at the bottom of the seat back),
inserting each buckle into the
corresponding buckle housing in
the matching strap.
NOTE: Before using your stroller, be sure to attach the tether straps around the stroller frame by feeding the strap through
the slit in the steel buckle. While not essential for safety, these help reduce the motion of the seat within the stroller frame.
NOTE: Special care must be taken when
adjusting the seat position with a child in
the stroller. Before adjusting the zippers,
place your hand beneath the seat at its
current position and lift it slightly. This will
relieve pressure on the zippers and make
them easier to adjust.
There are two available brake systems
available for the Runabout Tri Mode
series:
STANDARD BRAKE (pictured)
1. Press down on the centre of the
brake bar until the bar ends engage
in the nylon brake cogs on the
wheel.
2. To disengage, lift the brake bar
upward till it locks in the upright
position.
CONCEALED BRAKE:
1. Press the centre toggle down firmly
with your foot until you feel the
wheels have locked.
2. To release, lift the centre toggle
from beneath with your foot.
IMPORTANT WARNING: Alwa
y
s test that all axles
,
wheels
,
front bar
,
hin
g
es and locks a
r
e securel
y
en
g
a
g
ed before use.

Your Runabout stroller is fitted with our unique new multi point safety harness system. Your
child MUST always be harnessed while in the stroller.
TO SECURE YOUR CHILD IN THE HARNESS:
1. Overlap buckles (A) and (B) so that they fit together to form one complete buckle.
2. Insert the completed buckle into the Buckle Housing (C) until it engages securely in place.
3. Carefully adjust the harness straps to snugly fit your child by adjusting the Sliders located on all
Shoulder Straps, Waist Straps and the Crotch Strap.
4. Your harness can be adjusted for even more comfort for smaller or larger children (at the top of the
seat back and front of the seat) by threading/removing the shoulder straps through the webbing
sewn into the seat. (NOTE: Your stroller must ONLY be used with the Crotch strap threaded
beneath the front webbing strap.) You will need to detach the waist straps at the sides of the stroller
in order to do so. (To detach the waist straps: With a pincer movement, depress the centre buckle
button and pull the strap free from the housing.)
5. To prevent older children tampering with the strap adjustments and for greater child comfort, your
RUNABOUT stroller is provided with 2 soft strap covers for each harness. To fit, detach the waist
straps at the sides of the stroller (as in point 4) and thread the strap through the strap cover. Re-
attach each strap.
The harness should be snugly fitted to the baby’s body, tight enough so that the baby cannot
wriggle itself free of the straps but loose enough so as not to cause the baby any discomfort.
Usin
g
y
our harness
Your Runabout is equipped with a tire
pump that hangs in a special pocket found
sewn beneath the seat at the rear.
Your tires should be kept at a pressure of
40 p.s.i. Under inflated tyres can cause
excessive and uneven tire wear, greater
susceptibility to punctures and greater
difficulty in smooth operation.
Your Runabout is equipped with a
removable “Head Hugger” and
shoulder harness covers. The “Head
Hugger” is designed to optimize the
comfort of newborn babies within the
stroller. The shoulder straps increase
your child’s comfort levels when in the
harness as well as keeping harness
adjusters away from busy fingers.
EXTRAS
Your Runabout hood is fitted with a zip
system to which attaches our unique
silver insect mesh (optional extra on
most models)
This protective mesh has been tested
and proven to block out up to 80%*of
UV rays
(*tested to Australian Standard 4399)
O
p
tional Extra on most models
AIRGO™ SYSTEM
Your Runabout has been designed to maximise air flow within the
stroller by way of our exclusive Airgo™ system. This unique
system combines a special breathable seat fabric, with our new
flexible hood. The hood incorporates a built in storage bag,
designed to zip off when more air flow is required, to reveal an
additional mesh air vent. The bag is designed “to go” or can be
easily hung from the stroller handle.
TO OPEN YOUR HARNESS:
1. Press down on the Buckle Prongs (1).
2. Simultaneously push the release button in the centre of the buckle (2)
3. Pull the buckles from the Buckle Housing.
Your harness system has been designed to meet very stringent safety standards and incorporates our
unique secondary action. This helps ensure that your child cannot release the harness unaided.
2
C
1
A
B

OPTIONAL/ADDITIONAL
ACCESSORIES
UV Protective Insect Net
Our unique insect net zips directly in to the inside of your
RUNABOUT Tri Mode hood. In addition to keeping baby cool,
comfortable and safe from insects, it also blocks up to a
massive 80%*of the sun’s harmful UV rays.
(*tested to Australian Standard 4399)
Toddlerseat
Available in versions for both Single and Twin Runabout models, the
optional toddlerseat sits firmly inside the chassis. Perfect for twins
and an older sibling (Twin model) or when a new baby comes along
and junior still likes to go for a ride! Both Twin and single models
even fold totally out of the way with the stroller! See your local
specialist retailer for more info and suitability.
Travel Storage Bag
Available in BLACK only, the
travel bag is specifically
tailored to the RUNABOUT
model and provides sections
and compartments for all the
components including
wheels, axles etc.
Boot cover
The generous proportions of
this fleecy lined boot keep
your child warm and
protected from the elements
while offering a sense of
space without constriction.
Foot Muff
With tailored slots for the
harness system, the fleecy
lined muff keeps your child
comfortable in cool conditions,
while the top zips off to convert
it to a comfy stroller pad.
4 Season Foot Muf
f
With all the features of the
standard model, the 4 season
model includes a zip out top
section which reveals our
unique 80%* UV protective net.
This allows even more cool
and regulated airflow in warmer
conditions.
Sunstopper (Universal fit)
The unique SUNSTOPPER
provides the ultimate protection
from the suns harsh rays, while
providing a comfortable open
environment for the child. The roll
up blind system means that the
child can be shielded from the
sun without being fully enclosed,
and folds up into its own self
enclosed pouch for easy storage.
Bottle/Cup Holde
r
(Universal fit)
The revolutionary VALCO
BABY cup/bottle holder was
designed for the busy lifestyle
of today’s parents and carers.
With the specially designed
holding section big enough to
accommodate up to a 1.5 litre
bottle or those big coffee cups,
refreshment is always within
easy reach!

The VALCO HITCHHIKER is a boon to any parent with a child who is old enough to walk but young
enough to need to rest along the way. Made of high quality and extremely sturdy materials (maximum
weight 30 kg’s / 66 lb’s), the HITCHHIKER is easily adjustable for height, width and distance from the
stroller which makes it fit most brands, makes and models of strollers. The handy “hang up” system
means it can hang out of the way when not in use, while the unique quick release systems allows for
quick and easy removal.
All this and more makes the HITCHHIKER the perfect option for that “in between” age child. See your
local specialist retailer for more information.
OPTIONAL ACCESSORIES

WARNINGS
Your child’s safet
y
is
y
our res
p
onsibilit
y
………
Be sure to check that all clamps and buckles are securely fixed and in place before use.
Check all parts for breakage or fatigue before use. Discontinue immediately if any part is found to
be damaged or broken.
The maximum weight of the child for which this stroller is intended is 22 kg’s (48 lbs)
The maximum height of the child for which this stroller is intended is 106 cm (42 in)
This product will become unstable if the recommended load is exceeded.
Can be used from birth +. A cocoon specially designed to be used with a stroller is recommended
when any fully reclining stroller is used with a newborn.
NEVER jog with a newborn baby in any pram or stroller until the child can sit up
unassisted (approximately 6 months).
ALWAYS ensure that the child is clear of all moving parts when adjusting the stroller.
ALWAYS beware of little fingers when folding or unfolding your stroller to prevent finger
entrapments.
ALWAYS engage the brake system when the stroller is at rest.
NEVER leave any child unattended in the stroller.
NEVER use on escalators or stairs.
When in the stroller the child must ALWAYS wear the safety harness, correctly fitted and adjusted,
at all times.
DO NOT hang shopping bags from the handle as this may affect the stroller’s stability.
Always use the basket provided, the maximum weight in the basket is 6 kg’s (13 lbs)
Do not carry additional children. It may be unsafe to use any accessories other than VALCO
approved ones.
ALWAYS be aware of the risks provided by fire and other significant sources of heat such as
radiators etc. which may be in the immediate vicinity of your stroller.
This product is intended for domestic use only. It is not intended for commercial use.
Continued and extended exposure to sunlight and the elements can change the colours of many
materials. To avoid fadin
g,
alwa
y
s cover and store in a shaded area.
Caring for your stroller
Moving parts may be lubricated with silicone based lubricants – do not use oil.
Regularly check wheels for loose spokes – tighten as necessary.
Your Runabout chassis is made of aluminium alloy but does include some metal parts. Special
care must always be taken to avoid rust. If this pram is used near the ocean or salty air
environments, spray the chassis and seat frame with water and dry thoroughly. This is
particularly important for parts such as wheel spokes and springs. We recommend rust
inhibiting product should be applied to prevent accelerated rust and fatigue of these metal parts!
We recommend that you wipe down axles and lubricate the wheels every 3 months,
particularly the front wheel and housing. Sand and dirt can grind down axles so, if you
live, walk or run near/on the beach or in a dusty environment, you must remove and
wipe down the axles and wheels, then lubricate them MONTHLY.
AXLES AND MOVING PARTS ARE BEST LUBRICATED WITH SILICONE BASED
PRODUCTS. DO NOT USE OIL BASED PRODUCTS.
www.valcobaby.com
1 800 610-7850
In North America
www.valco.com.au
www.valco.co.nz
In Australia/NZ
© Co
py
ri
g
ht VE 2006