VALCOBABY Vee Bee Dash Installation and operation manual

PAGE 1
by valco baby
DASH
Stroller
© Copyright VB 2016
vs100216
PRODUCT REFERENCE GUIDE
Thank you for purchasing a quality VEE BEE product.
Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction
and safety features; be sure that you understand all the
warnings and safety guidelines before use.
Important: Please read the following instructions
carefully before assembling this product. Retain this
guide in a safe place for future reference.
Due to our policy of continuous product development,
this product is constantly evolving. It is possible that
some features or procedures outlined here have changed
since this document was written. If you are unsure of
any procedure shown here, please contact us via the
web at [e-mail] to obtain the most up to date
information before use. Include the batch number, which
can be found on a sticker on the frame.
All pictures and diagrams herein are provided for
illustration purposes only. Actual product, colour or fabric
may vary. VALCO BABY reserves the right to modify or alter
any specication or colour without notice or obligation to
modify any product previously purchased
FURTHER INFORMATION
In Australia/New Zealand
www.veebee.com.au
DISCLAIMER
1>PARTS LIST
2x front
Wheels
2x rear
Wheels
Stroller frame
& seat with
hood
DashIM_190718.indd 1 19/7/18 4:20 pm

PAGE 2
2>OPEN
3>FRONT WHEELS
4>REAR WHEELS
CLICK
CLICK
PRESS
DashIM_190718.indd 2 19/7/18 4:20 pm

PAGE 3
5>HOOD
6>BUMPER BAR
7>HANDLE BAR
8>BRAKE
ZIP
TO ATTACH
CLICK
PRESS
PRESS
PRESS
CLICK
WARNING: BE SURE BRAKE IS APPLIED
WHENEVER STROLLER IS STATIONARY.
DashIM_190718.indd 3 19/7/18 4:20 pm

PAGE 4
9>FOLDING
10>SEAT RECLINE 11>FOOTREST
1.FOLD HOOD
2. INCLINE SEAT
4. LIFT
5. FOLDED
PRESS
3. UNLOCK
SQUEEZE
& PULL
RECLINE INCLINE
SQUEEZE
& PULL
PRESS
RAISE
LOWER
DashIM_190718.indd 4 19/7/18 4:20 pm

PAGE 5
‘PRESS’
CLICK
11>FOOTREST
12>HARNESS
a
C
b
d
e
ALWAYS USE THE
RESTRAINT SYSTEM
DashIM_190718.indd 5 19/7/18 4:20 pm

PAGE 6
13>TETHER STRAP
1>PARTS LIST
1x hood, 2x rear wheels, 2x front wheels,
stroller frame/seat.
2>TO OPEN
Remove the carton contents carefully.
Dispose of any packaging materials
thoughtfully .
Release the stroller from the locked
position by lifting the locking hinge from
over the locking rivet on the stroller frame.
Lift the handle upward until the frame locks
in the upright position.
IMPORTANT WARNING: ALWAYS
TEST THAT ALL LATCHES ARE
SECURELY ENGAGED BEFORE USE.
3>FRONT WHEELS
Lay the stroller on its’ back so that the handle
bar is resting on the floor. Insert the front
wheel pin by sliding it into the front wheel
mount until you hear a ‘click’. Gently pull on
the front wheel to make sure it is properly
engaged.
To remove the wheel, press the button on
the wheel casing and pull wheel gently away
from the stroller.
To swivel front wheel: raise the swivel lock
to allow the front wheel assembly to swivel.
To lock the wheels, press down on the
swivel lock to lock the front wheel assembly
in a fixed position.
IMPORTANT WARNING: ALWAYS
TEST
THAT WHEELS ARE SECURELY
ENGAGED IN EACH WHEEL MOUNT
BEFORE
USE.
4>REAR WHEELS
Align the rear wheel axle with the wheel
mount on the stroller frame and insert it
into the wheel mount until it ‘clicks’ into
place.
Gently pull on the rear wheel to make sure
it is properly engaged.
To remove the rear wheel, press the wheel
release button and gently slide the wheel
out of the wheel mount.
5>HOOD
To attach the hood: locate the hood
mounting joint on the frame of your stroller.
Slide the hood attachment brackets
downward onto the mount on both sides.
Secure each side of the hood to the frame
by engaging the buttonhole over the rivet
head found on the underside of the frame.
For additional ventilation, your hood is
fitted with our additional airflow system.
Simply undo the zip carefully and pull your
hood forward. To close, zipper the section
back in place being careful that the mesh
does not become caught in the zip.
6>BUMPER BAR
To attach the bumper bar, press and hold
the buttons on both sides of bumper bar
mounting and insert bumper bar end into
INSTRUCTIONS
WARNING: ALWAYS WEAR THIS STRAP TO
STOP THE PRAM/STROLLER ROLLING AWAY
DashIM_190718.indd 6 19/7/18 4:20 pm

PAGE 7
www.veebee.com.au
each corresponding hole in the frame.
To remove the bumper bar:
reverse the
above steps. Always test that bumper bar is
securely engaged before use.
7>HANDLE BAR
To adjust the handle bar height, press
and hold the buttons on either side of the
handle bar while raising or lowering.
8>BRAKE
To engage the brake, simply push the red
brake pedal down (the one brake pedal
engages both brakes.) To disengage the
brake, lift the red brake pedal upward.
WARNING: ALWAYS BE SURE BOTH
WHEEL BRAKES ARE ENGAGED
WHEN THE STROLLER IS AT REST.
9>TO FOLD YOUR STROLLER
Remove the child from the seat. Incline the
seat and fold the hood. Press the release
button on the right hand side of the real leg
to release the main lock.
Locate the pull strap found in the centre of
the seat pocket and pull upwards on the
pull strap with a gentle tug, Your stroller
will fold in half. Ensure that the frame lock
is engaged.
ALWAYS ENGAGE THE FRAME LOCK
WHEN FOLDED. TAKE CARE WHEN
LIFTING THE STROLLER TO KEEP YOUR
KNEES BENT AND BACK STRAIGHT. DO
NOT CARRY THE STROLLER BY THE HOOD,
BUMPER BAR OR THE REAR BRAKE AXLE.
10>SEAT RECLINE
To lower the seat: Pinch the clamp behind
the seat and slide it down to the desired
position. Pull the seat down on both sides
to match the recline position of the clamp.
To raise the seat; lift the seat and hold
at the desired position. Pinch the clamp
behind the seat and slide it up to the
desired position.
NOTE: ALWAYS TEST THAT THE
SEAT IS SECURELY FIXED IN
POSITION BEFORE USE. SPECIAL CARE
MUST BE TAKEN WHEN ADJUSTING THE
SEAT POSITION WITH A CHILD IN THE
STROLLER.
11>FOOTREST
To adjust your footrest downward, press
the buttons on each side of the footrest
while simultaneously pressing down lightly
on the footrest.
To raise the footrest, simply lift it with your hand.
12>HARNESS
Your stroller harness is specifically
designed with many built in safety features.
This includes the requirement that, when
opened, all straps are released so that no
dangerous loops can be formed causing a
strangulation hazard.
WARNING: YOUR CHILD MUST
ALWAYS BE HARNESSED WHEN IN
THE STROLLER
Closing your harness: Slide each of the
shoulder strap bottom guides (a) into the
corresponding channel on the top of each
side strap prong. Insert each completed
prong into the central buckle housing (b).
Carefully adjust the harness straps to snugly
fit your child by adjusting the sliders (c)
located on each strap. The harness should
be fitted to your child’s body, tight enough
so that they cannot wriggle free of the straps
but, loose enough, so as not to cause any
discomfort.
For even more flexibility, the height at
which your shoulder straps are fitted to the
stroller can be adjusted at 3 points(d).
To change the shoulder strap position:
Open the harness. Re thread the shoulder
strap back through the desired loop on the
front of the seat
Opening your harness: Press the central
housing button (e). This will release both
side prongs from the central housing.
The shoulder and waist straps will release
automatically from each other.
If the shoulder and waist straps do not
automatically disengage from each other,
manually slide the guides of the waist
channels. Your harness will separate into
5 sections.
IMPORTANT WARNING: WHEN NOT
IN USE, BE SURE THE SHOULDER
AND WAIST STRAPS ARE ALWAYS
DISCONNECTED FROM THE CENTRAL
HOUSING AND EACH OTHER
13>TETHER STRAP
WARNING: USE THIS STRAP TO
STOP THE PRAM/STROLLER
ROLLING AWAY.
DashIM_190718.indd 7 19/7/18 4:20 pm

PAGE 8
FURTHER INFORMATION:
veebee.com.au
Find us on:
WARNING: TO AVOID INJURY OR DEATH
• FOLLOW THE MANUFACTURER’S INSTRUCTION
• PUT ON ALL THE BRAKES WHENEVER YOU PARK PRAM/STROLLER*
• DO NOT LEAVE CHILDREN UNATTENDED.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER*.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE PRAM/
STROLLER*, OTHERWISE THEY MAY BE INJURED.
• SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
• WHEN NOT IN USE DISCONNECT SHOULDER STRAPS FROM THE
WAIST STRAP AND/OR BUCKLE.
• THIS STROLLER IS NOT SUITABLE FOR RUNNING OR SKATING
•NEVER USE ON STAIRS OR ESCALATORS.
• ALWAYS USE THE TETHER STRAP WHEN THE STROLLER IS IN USE.
• THE CORRECT USE AND MAINTENANCE OF THIS VEHICLE ARE ESSENTIAL.
• BE SURE THAT ALL CLAMPS AND BUCKLES ARE SECURELY FIXED AND IN PLACE BEFORE USE
• USE THIS HARNESS AT ALL TIMES. ALWAYS USE THE HARNESS, CORRECTLY FITTED AND ADJUSTED,
WITH YOUR CHILD IN THIS SEAT.
• THE MAXIMUM TESTED WEIGHT OF EACH CHILD FOR WHICH THIS
STROLLER WAS INTENDED IS 15 KGS (33LBS) AND MAXIMUM RECOMMENDED WEIGHT IS 20KGS
(44LBS). THE MAXIMUM WEIGHT CAPACITY FOR THIS PRAM, POCKETS, STORAGE CONTAINERS,
AND OTHER ACCESSORIES SUCH AS A TODDLER SEAT OR TODDLER PLATFORM IS 17KGS
(34.7LBS). EXCESSIVE WEIGHT MAY CAUSE A HAZARDOUS UNSTABLE CONDITION TO EXIST.
• THE
MAXIMUM HEIGHT OF THE CHILD FOR WHICH THIS STROLLER WAS INTENDED IS 90CM (35INCHES).
• THE STROLLER MAY BECOME UNSTABLE IF THE MANUFACTURER’S RECOMMENDED LOAD IS EXCEEDED.
• CARE MUST BE TAKEN WHEN FOLDING AND UNFOLDING THE PRODUCT TO PREVENT
FINGER ENTRAPMENT.
• NEVER RUN WITH A NEWBORN BABY IN ANY PRAM OR STROLLER UNTIL THE CHILD CAN SIT UP
UNASSISTED (APPROXIMATELY 6 MONTHS).
• CHECK ALL PARTS BEFORE USE FOR BREAKAGE OR FATIGUE. DISCONTINUE USE IMMEDIATELY
IF ANY PART IS FOUND TO BE DAMAGED OR BROKEN.
• MAXIMUM LOAD OF BASKETS: 2KGS (4.5LBS).
•
DO NOT CARRY ADDITIONAL CHILDREN. THIS STROLLER IS MANUFACTURED FOR USE WITH ONE
CHILD ONLY.
• ALWAYS BE AWARE OF THE RISKS PROVIDED BY FIRE AND OTHER SIGNIFICANT SOURCES OF HEAT
SUCH AS RADIATORS, ETC. WHICH MAY BE IN THE IMMEDIATE VICINITY OF YOUR STROLLER.
• IT MAY BE UNSAFE TO USE ANY ACCESSORIES OTHER THAN VALCO BABY APPROVED ONES.
• THIS PRODUCT IS INTENDED FOR DOMESTIC USE ONLY. IT IS NOT INTENDED FOR COMMERCIAL USE.
• THIS STROLLER IS DESIGNED FOR USE ON FLAT OR GENTLY SLOPING SURFACES AND MAY BECOME
UNSTABLE OR TIP OVER IF USED ON HIGH SLOPING OR UNEVEN SURFACES.
• ALWAYS ENGAGE THE FRAME LOCK WHEN FOLDED. TAKE CARE WHEN LIFTING THE VEHICLE
TO KEEP YOUR KNEES BENT AND BACK STRAIGHT. DO NOT CARRY THE VEHICLE BY THE HOOD,
BUMPER BAR OR THE REAR BRAKE AXLE.
Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean or salted roads, spray the chassis and seat
frame with water and dry. We recommend a rust inhibiting product should be used to prevent rust and fatigue on metal parts. We recommend
that you wipe down axles and lubricate the wheels every 3 months. Sand and dirt can grind down axles, if you live near the beach or in a dusty
environment you must wipe down the axles and wheels then lubricate them monthly.
AXLES ARE BEST LUBRICATED WITH GREASE OR PETROLEUM JELLY. MOVING PARTS ARE BEST LUBRICATED WITH SILICONE BASED PRODUCTS.
DO NOT USE OIL BASED PRODUCTS.
WARNING
WARNING
DashIM_190718.indd 8 19/7/18 4:20 pm