VALCOBABY REBEL Q SPORT Installation and operation manual

© Copyright
VE 2012
vs190312
FURTHER INFORMATION:
www.valco.com.au
Find us on:
REBEL Q
SPORT
Stroller
PRODUCT REFERENCE GUIDE

Due to our policy of continuous product development,
this product is constantly evolving. It is possible that
some features or procedures outlined here have
changed since this document was written. If you are
unsure of any procedure shown here, please contact
us via the web at [email protected] to obtain the
most up to date information before use. Include the
batch number and model number, which can be found
on a sticker on the frame.
All pictures and diagrams herein are provided for illustration
purposes only.
Actual product, colour or fabric may vary.
VALCO BABY reserves the right to modify or alter any
specification or colour without notice or obligation to
modify any product previously purchased.
REBEL Q
SPORT
Stroller
Thank you for purchasing a quality VALCO BABY product. Please read and follow the instructions
outlined in this guide carefully. Familiarise yourself with the construction and safety features; be
sure that you understand all the warnings and safety guidelines before use.
Important: Please read the following instructions carefully before assembling
this product. Retain this guide in a safe place for future reference.
BUMPER
BAR
HOOD
REAR WHEELS x 2
AXELS
SEAT
STROLLER FRAME
2 x FRONT WHEELS
A
B
C
DD
E
F
G
1>PARTS LIST
DISCLAIMER

a
c
b
e
f
g
d
j
5>INSTALL SEAT
h
i
2>TO OPEN
3>REAR WHEELS
4>FRONT WHEELS

6>BUMPER BAR
7>HOOD
8>SEAT RECLINE
9>BRAKES 10>FOOTREST
o
q
r
l
n
1 2 3
p
PRESS
HERE TO
RELEASE
k

11>HARNESS
12>HANDLE
10>FOLDING
st
u
v
W
p
p
x
x
z
y
y

1>PARTS LIST
1x bumper bar (A), 1x hood (B), 2x rear
wheels (C), 2x front wheels (D), axles (E)
seat (F), stroller frame (G).
2>TO OPEN
Lay the stroller frame flat on the ground
with the handle facing upwards. Release the
frame lock if engaged (a)
Lift the handle upward to a vertical position.
You will feel the chassis unfolding as you lift.
Continue to lift the handle until you feel the
chassis lock into the open position.
IMPORTANT WARNING: ALWAYS TEST
THAT ALL LATCHES ARE SECURELY
ENGAGED BEFORE USE.
3>REAR WHEELS
Pressing on the axle release button (b),
insert the axle through the outside of the
metal hub and through the nylon brake cog.
IMPORTANT: INSERT THROUGH OUTSIDE
OF THE WHEEL - THE SIDE WHICH DOES
NOT HAVE THE BRAKE COG SPROCKETS
While pressing the axle release button (b),
insert the wheel axle into the wheel housing of
the frame at the rear of the stroller chassis (c).
Keeping the axle release button depressed,
insert the wheel as far as it will go into the
channel. Release the button and pull the
wheel slightly back toward you to ensuring
that it has locked securely into place. Repeat
this procedure for the other wheel.
To remove a rear wheel, firmly grasp the
wheel spokes while pressing the axle
release button. Gently pull the wheel free of
the wheel housing.
4>FRONT WHEELS
Line each front wheel pin (d) with the
corresponding front wheel housing (e).
Insert wheel pin into the wheel housing and
push it up until it clicks into place.
To remove the wheel, press down firmly on
the release button (f) while pulling the wheel
free of the housing.
The front wheels of your stroller offer either a
full, 360º swivel action or a locked position.
To lock the front wheel, turn the wheel so
that the bulk of it is beneath the stroller
and push down on the wheel lock (g) until
it locks into position. Repeat this procedure
for the other side.
IMPORTANT WARNING: ALWAYS TEST
THAT THE LOCKS ARE FULLY ENGAGED
BEFORE USE.
5>INSTALL SEAT
Line up the seat housing (h) with the
corresponding connectors (i) located on
either side of the stroller frame. Lower the
seat onto the connectors and gently push
the seat down until it clicks securely into
place.
NOTE: YOUR SEAT CAN BE INSTALLED
EITHER FORWARD OR REARWARD FACING.
To remove the seat, simultaneously lift one
trigger (j) on each side of the seat housings
(this can be operated from either the front
or rear of the housing) and lift the seat unit
from the frame.
6>BUMPER BAR
Insert each side of the bumper bar fitting
into the corresponding housing in the seat
frame until you hear it click into place.
The bumper bar can be opened as a “gate”
for easy access pressing on one of the
release buttons (k) and lifting the side out
of the housing. For full removal, repeat this
process for the other side.
7>HOOD
Locate the hood stud rivets found on either
side of the stroller, and align hood clamp
over each rivet. Secure clamp onto frame (l).
WARNING: HOOD MUST ALWAYS BE
FULLY INSTALLED AND ATTACHED TO
FRMAE WHEN USING SEAT IN THE FULLY
RECLINED POSITION.
The Expanda hood unzips, increasing the
size of your standard hood, to give greater
coverage and protection from the sun and
elements for your child.
T
o open the Expanda Hood: Locate the zip
in the center of the Expanda Hood and unzip
completely (n). Gently pull the Expanda Hood
forward until it is reaches its full extension.
To close the Expanda Hood: Gently push the
Expanda Hood back, allowing the middle
section to fold in on itself. Carefully zip the
Expanda Hood closed.
The hood offers a flow through ventilation
cap at the rear (o). To allow ventilation
simply flip the cap down.
INSTRUCTIONS

8>SEAT RECLINE
The stroller seat has 3 positions. To recline
or incline the seat simultaneously push the
adjusting buttons located on either side of
the seat housing (p) and move the seat into
the desired position.
NOTE: SPECIAL CARE MUST BE TAKEN
WHEN ADJUSTING THE SEAT POSITION
WITH A CHILD IN THE STROLLER.
9>BRAKES
Press down on the red brake lever (q)
located on the rear axle to simultaneously
engage the brake in both rear wheels.
To release, press down on the shorter leg
with your foot.
IMPORTANT WARNING: ALWAYS TEST
THAT THE BRAKES ARE SECURELY
DISENGAGED BEFORE USE.
10>FOOTREST
To raise the footrest simply lift the end up to
the desired position. To lower your footrest,
simultaneously press the two adjusting
buttons (r) on either side of the footrest
allow it to drop down.
11>HARNESS
Your stroller harness is specifically designed
with many built in safety features.
This includes the requirement that, when
opened, all straps are released so that no
dangerous loops can be formed causing a
strangulation hazard.
WARNING: YOUR CHILD MUST ALWAYS
BE HARNESSED WHEN IN THE STROLLER
Closing your harness: Slide each of the
shoulder strap bottom guides (s) into the
corresponding channel (t) on the top of each
side strap prong. Insert each completed prong
into the central buckle housing (w).
Carefully adjust the harness straps to snugly fit
your child by adjusting the sliders (v) located
on each strap. The harness should be fitted
to your child’s body, tight enough so that they
cannot wriggle free of the straps but, loose
enough, so as not to cause any discomfort.
For even more flexibility, the height at which
your shoulder straps are fitted to the stroller
can be adjusted at 3 points(v).
To change the shoulder strap position:
From the rear of the seat, thread the top of
the strap back through the harness slot (it
fits through the slot.
Rethread the strap back through the desired
slot from the front of the seat
Opening your harness: Press the central
housing button (w). This will release both
side prongs from the central housing.
The shoulder and waist straps will release
automatically from each other.
If the shoulder and waist straps do not
automatically disengage from each other,
manually slide the guides of the waist
channels. Your harness will separate into 5
sections.
IMPORTANT WARNING: WHEN NOT IN
USE, BE SURE THE SHOULDER AND WAIST
STRAPS ARE ALWAYS DISCONNECTED FROM
THE CENTRAL HOUSING AND EACH OTHER
.
12>HANDLE
Your handle can be adjusted to multiple
positions. Press the centre locking button
(x) while simultaneously moving the handle
up or down.
Releasing the locking button will allow the
handle to lock into the next position.
12>FOLDING
Adjust the handle down to its lowest
position. While still keeping the central
locking button (x) pressed, hold the frame
lock button (z) firmly depressed. Continue to
push the handle firmly in the direction of the
chassis, past the frame lock until it engages
the lock spring. This will unlock the frame.
Press down on the handle to fold the frame
and continue to ease the handle downward
until the frame is fully collapsed and the
chassis locks closed at (a). Adjust the seat
to its most reclined position as outlined in 8.
Depending on which way your seat is facing
when folded, your Rebel Q Sport seat can
be made to fold even more compactly
by simultaneously pressing the transport
position buttons (y) and seat adjustment
buttons (p), thereby allowing the seat to
swing even further downward.
IMPORTANT: WHEN REOPENING THE
STROLLER, BE SURE TO LIFT THE SEAT
BACK UP INTO THE USE POSITION
BEFORE USE!

FURTHER INFORMATION:
www.valco.com.au
Find us on:
WARNING: TO AVOID INJURY OR DEATH





 
 



•NEVER USE ON STAIRS OR ESCALATORS.



! .













.





USE.
Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean or salted roads, spray the
chassis and seat frame with water and dry. We recommend a rust inhibiting product should be used to prevent rust and fatigue on
metal parts.

near the beach or in a dusty environment you must wipe down the axles and wheels then lubricate them monthly.

