VALCOBABY Zeetwo Installation and operation manual

PRODUCT REFERENCE GUIDE
© Copyright VE 2011
vs091111
Due to our policy of continuous product
development, this product is constantly
evolving. It is possible that some features or
procedures outlined here have changed since
this document was written. If you are unsure
of any procedure shown here, please contact
us via the web at [e-mail] to obtain
the most up to date information before use.
Include the batch number, which can be found
on a sticker on the frame.
All pictures and diagrams herein are provided
for illustration purposes only.
Actual product, colour or fabric may vary.
VALCO BABY reserves the right to modify or
alter any specication or colour without notice
or obligation to modify any product previously
purchased
Stroller
FURTHER INFORMATION
In Australia/New Zealand
www.valco.com.au
In North America only
www.valcobaby.com
[e-mail]
1800 610 7850
Thank you for purchasing a quality VALCO BABY product. Please read and follow the instructions outlined in
this guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand
all the warnings and safety guidelines before use.
Important: READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF PRODUCT.
KEEP INSTRUCTIONS FOR FUTURE USE.
two

ASSEMBLY
FIGURE A - CONTENTS
1. Remove the stroller from the
carton and dispose of all packaging
thoughtfully. Check contents.
FIGURE B - OPENING
2. Release frame lock on side of stroller
frame.
3. Lift the stroller handle upward over
180° until it locks into a straight line.
4. With one hand holding the lower legs
down, lift the handle vertically until
the lower chassis locks into position.
(You should hear an audible ‘click’).
IMPORTANT WARNING:
ALWAYS TEST THAT ALL LATCHES ARE SECURELY
ENGAGED BEFORE USE.
FIGURE C - INSERTING REAR AXLE
5. Align the plastic housings of the rear
brake section with the open tubes of
the rear of the stroller chassis.
IMPORTANT: BE SURE THAT THE BRAKE LEVER IS
UPRIGHT
6. Insert the housings over the open
tubes until the brake section locks
securely into place.
IMPORTANT WARNING:
TEST THAT THE BRAKE SECTION IS SECURELY
ENGAGED ONTO THE STROLLER FRAME BY PULLING
ON IT FIRMLY.
A
B
C
▲
!
▲
!
▲
!
▲
!
3
4
2
2 x HOODS
BASKET
2 x FRONT WHEELS
2 x REAR WHEELS
BRAKE
2 x AXELS
BUMPER BAR
SEATSEAT

FIGURE D - ATTACHING THE BASKET
7. Align the basket frame with the open tubes at the
rear of the seat. Simultaneously pressing in the
locking buttons, slide the basket frame into
the housing until the buttons lock into
place. IMPORTANT: When basket is locked
into place - the locking buttons (pins) will
pop through the holes. (Otherwise it is not
securely engaged.)
8. Basket front - pass the front ap over the
bar between the seat and the seat frame.
Secure with the snaps. Pull the side aps
around the front and Velcro into place on
the front ap.
FIGURE E- INSERTING REAR WHEELS
9. Simultaneously press on the spring loaded axle
button and insert it through the central hub of the
rear wheel. Repeat this process for the other rear
wheel.
10. Pressing the axle button again, insert the axle
end into the side of the brake housing as far as it
will go. Release the axle button and pull slightly on
the wheel to ensure that it has securely engaged.
FIGURE F - FRONT WHEELS
11. Grasping the front wheel, align the shaft with the
hole in the underside of the swivel housing.
12. Depress the button on the top of the swivel
housing. Insert the shaft into the housing as far as
it can go until it engages securely.
13. Repeat the procedure for the other front wheel.
IMPORTANT: PULL THE WHEEL DOWNWARD TO TEST THAT IT
HAS SECURELY ENGAGED IN THE HOUSING.
LOCKING YOUR WHEELS
14. Your front wheels can be set to swivel freely
(360º) or can be xed in place for use over rough
or sandy surfaces.
15. To x the front wheel in the non swivel position,
turn the wheel so that the two notches on both
housings line up. Press down rmly on the swivel
lock until it locks into place.
16. To unlock simply lift the locking tab until it locks
in the open position.
FIGURE G - USING YOUR BRAKE SYSTEM
17. To engage the brake press down on the central
brake pedal, until the brakes engage fully into the
wheel cogs.
18. To disengage, simply reverse the process.
E
F
G
D
10
9
ATTACH LOCK

HFIGURE H - BUMPER BAR
19. Insert the front bar ends into the nylon housings
located on either side of the frame. Be sure that the
moulded arrows are facing forward, away from the frame.
Be sure that the bar is securely engaged.
20. Wrap the crotch strap around the installed bumper bar
and snap into position
21. Adjust the front bar by simultaneously pressing the
button on the bar housing and swivelling the bar to the
uppermost position. This is the only position for use
with a child in the stroller.
22. To remove the front bar: Feeling the side of the nylon
housing that sits below the frame at each side (facing
inward), locate the release button.
23. Press each release button inward while simultaneously
pulling upward on the bar housing. Repeat for the other
side. Note that this may be difcult to do as the bar is
secured rmly as a safety precaution.
IMPORTANT WARNING: THE FRONT BAR IS NEITHER A
RESTRAINING NOR CARRYING DEVICE.
FIGURE I - SEAT RECLINE
Our system offers an almost innite amount of individual
seat adjustments.
24. TO RECLINE: While squeezing the centre release
mechanism in a pincer action, ease the seat down to the
desired position.
25. TO INCLINE: Place your hand at the centre of the rear
of the seat. Pull the incline strap while gently pushing on
the rear of the seat until the desired position has been
reached.
FIGURE K- ADJUSTING YOUR FOOTREST
26.To adjust your foot rest downward, press the central
buttons on either side of the footrest while
simultaneously adjusting it up or down.
YOUR FOOTREST IS DESIGNED TO COLLAPSE IF EXCESS
WEIGHT IS APPLIED TO IT
FIGURE L
Each Expanda hood unzips, increasing the size of the
standard hood to give it greater coverage and protection
from the sun and weather for your child.
To open the Expanda Hood:
27. Locate the zip in the center of the Expanda Hood and
unzip completely
28. Gently pull the Expanda Hood forward until it is reaches
its full extension.
To close the Expanda Hood:
29. Gently push the Expanda Hood back, allowing the
middle section to fold in on itself.
30. Carefully zip the Expanda Hood closed.
PRESS PULL
I
click
K
L
IMPORTANT HOOD INSTALLATION INSTRUCTION
The Expanda hoods come xed to the stroller.
Secure the rear hood skirt to the frame
by passing the press stud through the slot
provided and rmly engaging the other half by
pressing strongly. Always test that the press
studs are fully and rmly engaged.
▲
!▲
!
HOOD SKIRT
SEAT SIDE

FIGURE M - FOLDING YOUR STROLLER
31. To ensure maximum compactness, prior to
folding your stroller:
- fold the hood closed back against the handle
- incline the seat upright and gently push inward
forward of the seat frame
- lower the bumper bar
- remove all contents from the basket
32. Locate the frame release on either side of the
handle. Lift the frame release buttons on either
side of the handle simultaneously upwards.
FIGURE N - FOLDING YOUR STROLLER
33. Swing the handle forward. As the handle passes
the fold joint (x), you will feel the lower chassis
release and fold downward in a ‘z’ shape.
FIGURE O - FOLDING YOUR STROLLER
34. Push the frame down completely until the frame
lock engages.
M
N
O

FIGURE P- TETHER STRAP
36. Your stroller has been equipped with a safety
tether strap. This strap has been designed to
always keep your stroller within constant reach.
IMPORTANT: ALWAYS SLIP THE LOOP IN THE STRAP
SECURELY OVER YOUR WRIST WHENEVER A CHILD IS IN
YOUR STROLLER.
FIGURE A - USING YOUR HARNESS
Your stroller is tted with our unique
multi point safety harness system.
IMPORTANT: YOUR CHILD MUST ALWAYS BE
HARNESSED WHILE IN THE STROLLER.
Please read these instructions carefully
before use.
FIGURE Q
TO OPEN YOUR HARNESS:
15. Push down on both Buckle Prongs.
16. Simultaneously press the release
button in the centre of the buckle.
17. Lift the buckles from the Buckle
Housing.
THIS PROCESS MAY BE DIFFICULT AS YOUR
BUCKLE SYSTEM HAS BEEN DESIGNED TO
MEET VERY STRINGENT SAFETY STANDARDS
AND ENSURE THAT A CHILD CANNOT RELEASE
THE HARNESS UNAIDED.
TO SECURE YOUR CHILD IN THE
HARNESS:
18. Overlap buckles and so that they t
together to form one complete buckle.
19. Insert the completed buckle into the Buckle
Housing until it engages securely in place.
IMPORTANT WARNING:
ALWAYS TEST THAT ALL LATCHES ARE SECURELY ENGAGED
BEFORE USE.
P
Q
PUSH
PRESS
DOWN
HOLD
DOWN
RELEASE
HOLD
CLICK
▲
!▲ !

ZEE TWO ACCESSORIES
CAR SEAT ADAPTORS:
Click your car seat right into your Zee Stroller.
Contact [e-mail] for specic models.
ALL SORTS:
Dress up your stroller with the All Sorts Seat Pad &
Head Hugger Set to suit your mood and enliven
your stroller.
GLO BUGZ:
Glo Bugz are an easy way to stay safe and visible
at night. Attaches easily to strollers, bikes,
backpacks and more.
CAR SEAT ADAPTORS
ALLSORTS
GLO BUGZ

In Australia/New Zealand
www.valco.com.au
In North America only
www.valcobaby.com
1 800 610 7850
WARNING: TO AVOID INjURY OR DEATH
• always apply the brakes whenever the pram/stroller is stationary
• Do not leave ChilDren UnattenDeD.
• seCUre the ChilD in the harness at all times.
• Do not Carry eXtra ChilDren or baGs on this pram/stroller.
• make sUre ChilDren are Clear oF any movinG parts iF yoU aDJUst the pram/stroller. otherwise
they may be inJUreD.
• warninG: Use this harness at all times.
• warninG: when not in Use DisConneCt shoUlDer straps From the waist strap anD/or bUCkle.
• Follow the manUFaCtUrer’s instrUCtions.
• parCels or aCCessory items, or both plaCeD on the Unit may CaUse the Unit to beCome Unstable
• warninG ChilD may slip into leGopeninGs anD stranGle. never Use in reClineD CarriaGe position(s)
Unless (manUFaCtUrer to insert proDUCt speCiFiC instrUCtions)
Remember, your child’s safety is your responsibility...
•NEVER USE ON STAIRS OR ESCALATORS.
• AlwAys use the tether strAp when the stroller is in use.
• the CorreCt use AnD MAintenAnCe oF this VehiCle Are essentiAl.
• Be sure thAt All ClAMps AnD BuCkles Are seCurely FixeD AnD in plACe BeFore use
• when in the stroller, your ChilD Must AlwAys weAr the sAFety hArness, CorreCtly FitteD AnD
ADjusteD, At All tiMes.
• AlwAys use the hArnesses, CorreCtly FitteD AnD ADjusteD, with eACh ChilD in his seAt.
• the MAxiMuM weight oF the ChilD For eACh seAt whiCh this stroller wAs intenDeD is 15kgs.
• the MAxiMuM height oF the ChilD For whiCh this stroller wAs intenDeD is 90CM (35inChes).
• the stroller will BeCoMe unstABle iF the MAnuFAturer’s reCoMMenDeD loAD is exCeeDeD.
• CAre Must Be tAken when FolDing AnD unFolDing the proDuCt to preVent Finger entrApMent.
• CAn Be useD FroM A newBorn BABy onwArDs. A CoCoon, speCiAlly DesigneD to Be useD with A
stroller, is reCoMMenDeD when Any Fully reClining stroller is useD with A newBorn.
• neVer run with A newBorn BABy in Any prAM or stroller until the ChilD CAn sit up unAssisteD
(ApproxiMAtely 6 Months).
• CheCk All pArts BeFore use For BreAkAge or FAtigue. DisContinue use iMMeDiAtely iF Any pArt is FounD
TO BE DAMAGED OR BROKEN.
• MAxiMuM CoMBineD loAD oF BAskets: 5kgs. (11lBs)
• Do not CArry ADDitionAl ChilDren. THIS STROLLER IS MANUFACTURED FOR THE USE WITH TWO CHILDREN ONLY
• AlwAys Be AwAre oF the risks proViDeD By Fire AnD other signiFiCAnt sourCes oF heAt suCh As
rADiAtors, etC. whiCh MAy Be in the iMMeDiAte ViCinity oF your stroller.
• it MAy Be unsAFe to use Any ACCessories other thAn VAlCo BABy ApproVeD ones.
• this proDuCt is intenDeD For DoMestiC use only. it is not intenDeD For CoMMerCiAl use.
Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean
or salted roads, spray the chassis and seat frame with water and dry. We recommend a rust inhibiting
product should be used to prevent rust and fatigue on metal parts.
We recommend that you wipe down axles and lubricate the wheels every 3 months. Sand and dirt can
grind down axles, if you live near the beach or in a dusty environment you must wipe down the axles and
wheels then lubricate them monthly.
AXLES ARE BEST LUBRICATED WITH GREASE OR PETROLEUM JELLY. MOVING PARTS ARE BEST
LUBRICATED WITH SILICONE BASED PRODUCTS. DO NOT USE OIL BASED PRODUCTS.