Valor 10 User manual

TITLE
Your Valor® 10
Remote Control

We hope you enjoy your
Valor®Radiant Gas Fireplace.
Refer to these simple remote
control instructions and
keep them handy to enjoy
your replace to the fullest.
For our video guide, visit
valorreplaces.com/remote
Sincerely,
The Valor Family,
Valor Fireplaces
BR10REM19E dec

QUICK START
Turn re ON
Press until you hear beeping and
appears. Takes about 20 seconds.
Pilot and ames go to high.
Adjust ames
Press or .
High or low ame
Double-click or .
HI or LO appears.
Flame goes to high ame rst
before going to low ame.
Pilot only
Press until you see the
replace pilot ame only.
Turn re OFF
Press until OFF ashes.
If you recently turned
the pilot o, give your
replace a few minutes
before starting up again.

QUICK SETUP
Choose time and temperature
To switch between °C and °F, press
together until mode changes.
Set time
1. Press together until –day– appears.
Press or to select the day of the week:
1=Mon 2=Tue 3=Wed 4=Thu
5=Fri 6=Sat 7=Sun
2. Press together until hour ashes.
Press or to select hour.
3. Press together until minutes ash.
Press or to select minutes.
4. To nish, press together.
PM
PM
AM
°F = 12-hour clock
°C = 24-hour clock
TIME/TEMP MODE
TIME MODE

THERMOSTAT
Your remote works like a thermostat.
Keep it an ideal distance from the
replace: 3–15 feet from the replace and
other heat sources, including the sun.
Set thermostat
The remote’s thermostat automatically
adjusts the re to maintain the
thermostat temperature you set.
1. Press until appears and
temperature ashes.
2. Press or to adjust.
3. Press to complete.
Turn ON/OFF
Click to switch thermostat on or o.
To create a preset schedule,
see Program Mode in your
Homeowner’s manual.

FAN AND LIGHT
Optional circulating fan
1. Press until ashes.
2. Click or to adjust fan.
3. To turn o, click until all four
speed level bars disappear.
Light with dimmer
Turn on/o
Click to switch light on or o.
Adjust brightness
1. Press until ashing.
2. Press or when light is on.
The fan will stop 10
minutes after the re
is o or at pilot.
Enjoy the replace
even when it’s o—
turn on the lights!

SAFETY
Safety lock
This safety setting locks all commands, except the button.
Turn on/o
Press together until appears or disappears.

SAFETY + SAVINGS
3–hour turndown
If your replace and remote are inactive for three
hours—say, if the remote is another room—your remote
automatically turns your replace down to pilot.
Benet
Save money in the long run. Program the temperature and
timer modes to maximize your heating experience even more.
7–Day pilot shutdown
If there is no activity after seven days, the Valor
SmartPilot System automatically shuts o the pilot.
Benet
The 7 day pilot shutdown is ideal if you happen to be away from home for an extended period of
time or don’t need the heat during warmer Spring and Summer months—
you could save up to 5 months of unnecessary pilot consumption per year.
Eco Mode
Click to turn on and o. appears or disappears.
To nd out more, please see your Homeowner’s Manual.

BATTERIES
Batteries in remote
Your remote display indicates when the battery is low .
The remote uses a 2 AAA alkaline batteries—Duracell or
Energizer. The batteries should last one to two seasons,
depending on usage. Remove the battery in the o-season
to extend battery life.
Still not working?
Did you know every replace has
a receiver that uses batteries?
For the receiver batteries,
see wall switch batteries on following pages.

Batteries beside wall switch
Receiver batteries are located next to the wall switch.
1. Pull o the FIREPLACE BATTERY ACCESS plate next to the wall
switch. The plate is attached with magnets. Do not pull the
connector by the wire.
2. Replace the batteries with 4 AA alkaline batteries (Duracell or
Energizer) orienting them as indicated inside the holder.
3. Put the battery holder and cover back in place.
BATTERIES
For remote control batteries, see previous page.

Magnetic
battery access plate
Battery holder
Snap connector
Remote battery and wall switch
BATTERIES

TROUBLESHOOTING
Remote control doesn’t work
1. If the batteries are low, the remote control system shuts o
the re completely. However, during a power outage, the
system will continue to work.
2. Switch to Duracell or Energizer alkaline batteries. They work
best with our remote control systems.
3. Replace the remote’s receiver batteries, located in your
battery holder beside the wall switch.
Tip: Keep batteries fresh. Switch out your batteries in the
battery holder next to the wall switch once a year with
4new AA Duracell or Energizer alkaline batteries.

TIPS
Tips
•Double-click to go directly
to LO (lowest) ame setting.
•Double-click to go directly
to HI (highest) ame setting.
• Only use alkaline batteries,
such as Duracell or Energizer.
•When using the remote, the
handset should be within
15 feet (4.5 metres) of the
replace.
•Don’t leave the handset on
the mantel or hearth.
•To keep out of children’s
reach, use the wall holder.
•Be patient when
programming: it can take a
while to set.
•Once you turn a pilot o, it
takes a few minutes before
your can turn it back on.
•During extreme cold
weather, leave your pilot
running to avoid problems
starting up.

Please take care and stay safe
Remember to be careful when using your replace.
If you can’t nd the answer here, nd your homeowner’s
manual at valorreplaces.com/manuals
For basic how-to videos on your remote,
go to valorreplaces.com/remotes
If you would like more information, contact your local
dealer for help or visit valorreplaces.com