Valor Plus User manual

SAFETY AND SAVINGS
Your Valor®
Remote Control

We hope you enjoy your Valor®Radiant Gas
Fireplace. Refer to these simple remote control
instructions and keep them handy to enjoy your
replace to the fullest.
For our video guide, visit

Sincerely,
The Valor Family,

BRREM20E Mar

GETTING STARTED

Press OFF and high ame button
until you hear beeping.
Takes up to 20 seconds.


Press OFF and low ame button
to change display.

Press high and low ame
buttons until time 6:00 ashes.
To set hour—
press high ame button.
To set —
press low ame button.

GETTING STARTED
REMOTE CONTROL

To turn up, press high ame button.
To turn down, press low ame button.

Press low ame button until
the replace ames shut o.

Press OFF.
Tip:
During extreme cold weather,
keep your replace ON to avoid
problems starting up.

WALL SWITCH
WALL SWITCH

Press  button
until you hear beeps.

Press button until  replace
and pilot  ame shut o .
You can’t control the thermostat
or timer with the wall switch. Use
remote instead.

SAFETY + SAVINGS
7–DAY PILOT SHUTDOWN
If there is no activity after seven days, the
Valor SmartPilot System automatically shuts o
the pilot.
Benet
The seven day pilot shutdown is ideal if you happen
to be away from home for an extended period of
time or don’t need the heat during warmer Spring
and Summer months—you could save up to 5
months of unnecessary pilot consumption per year.
8–HOUR TURNDOWN
If your replace ame height hasn’t changed
and you haven’t used your remote for
eight hours, your ValorStat Remote Control
System automatically turns your replace
down to pilot.
Benet
Save money in the long run. Use the temperature
and timer modes to maximize your heating
experience even more.

FAN + LIGHTING
CIRCULATING FAN*

Click SET button until fan ashes.
• To fan speed—
press high ame button.
• To fan speed—
press low ame button.

Press low ame button until all four
speed level bars disappear.
* Remote control with Valor Max remote only. Options available on select models.
OVERHEAD LIGHTING*

Click SET button until light bulb ashes.
• To turn on or light—
press high ame button.
• To light—
press low ame button.

Press OFF.

SET TEMPERATURE
SET THE TEMPERATURE
You can set a warmer and a cooler
temperature twice in one day.
Click SET button until TEMP appears.
Press SET button until temperature
 ashes.
To temperature, press
high  ame button. To 
temperature, press low  ame button.
Click SET button so TEMP appears.
Press SET button until temperature
 ashes.
Then, select temperature.
Press to save temperature settings,
or let remote automatically save the
setting after a few seconds.
To use temperature setting, make
sure TEMP mode is selected.
Click SET button to select
or temperature.

SET TIMER
SET THE TIMER
You can program two heat cycles for di erent times in
the day. Both cycles, P1 and, have a start and
an end time. Cycles cannot overlap. Before you set
the timer, set the temperature.
Click SET button until TIMER appears.
Press SET button until time 6:00  ashes. P1 
 appears.
To set the hour, press high  a m e
button. To set the ,
press low  ame button.
Click SET button so P1 
appears. Then, select time.
Click SET button so  
appears. Then, select time.
Click SET button so  
appears. Then, select time.
Press to save temperature
settings, or wait a few seconds.
Only want one heat cycle?
Set the time for these three: P1  and .

BATTERIES
BATTERIES IN REMOTE
Your remote display indicates when
the battery is low.
The remote uses a 
 The
battery should last ,
depending on usage. Remove the
battery in the o-season to 
.
Still not working? Did you know every
remote has a receiver that uses
batteries? See basic instructions
on next two pages.

BATTERIES
BATTERIES FOR YOUR RECEIVER


When three seconds of rapid re beeps
sound, it’s time to replace your receiver
batteries.
Locate the battery holder under the
rebox near the controls.
Replace the batteries with 
 batteries.
Return holder to original location.
Reinstall any remaining parts removed.
Have a remote battery and wall
switch instead? See next page.

Magnetic
battery
access plate
Battery
holder
Snap
connector

BATTERIES

BATTERIES IN REMOTE BATTERY
AND WALL SWITCH
If you have a remote battery and wall
switch, your receiver batteries are
conveniently located next to the wall
switch.
Pull o the FIREPLACE BATTERY
ACCESS plate next to the wall switch.
The plate is attached with magnets.
Do not pull the connector by the wire!
Replace the batteries with 

 orienting them as
indicated inside the holder.
Put the battery holder and cover
back in place.
If you don’t have a remote battery and
wall switch installed, see previous page.
BATTERIES

TIPS
TIPS
Double-click the low ame button to go directly to
LO (lowest) ame setting.
Double-click the high ame button to go directly
to HI (highest) ame setting.
Only use alkaline batteries, such as 
, with your remote or receiver.
When using the remote, the handset should be
within 15 feet (4½ metres) of the replace.
Don’t leave the handset on the mantel or hearth.
To keep out of children’s reach, use the wall holder.
Be patient when programming: it can take a few
seconds to set.
Once you turn a pilot o, it takes a few minutes
before your can turn it back on.
During extreme cold weather, leave your replace
running to avoid problems starting up.

TROUBLESHOOTING

Change the batteries in your remote
control. The battery usage icon on your
remote control screen will tell you if the
batteries are low or dead.
Switch to Duracell or Energizer alkaline
batteries. They work best with our
remote control systems.
Replace the remote’s receiver batteries
located in your replace or in your
remote battery and wall switch. Both
your remote and your remote’s receiver
require batteries.
 Keep batteries fresh. Switch out your
receiver’s batteries once a year with 
new or
batteries.

NOTES

NOTES

STAY SAFE
PLEASE TAKE CARE AND STAY SAFE
Remember to be careful when using your
replace.
If you can’t nd the answer in this
pamphlet, nd your owner’s manual at
valorreplaces.com/manuals.
For basic how-to videos on your remote,
go to valorreplaces.com/remotes
If you would like more information,
contact your local dealer for help or visit
valorreplaces.com

SOYEZ EN SÉCURITÉ

Rappelez-vous de faire attention lorsque vous
utilisez votre foyer à gaz.
Si vous ne pouvez pas trouver ce que vous
chercher dans ce guide, consultez votre Guide du
propriétaire dont vous pourrez trouver une copie
sur foyervalor.com
Pour une vidéo basique des fonctions de votre
télécommande (en anglais), visitez
valorreplaces.com/remotes
Pour plus de renseignements, contactez votre
détaillant Valor local ou visitez foyervalor.com

NOTES