Valor Plus User manual

SAFETY AND SAVINGS
Your Valor®
Remote Control

We hope you enjoy your
Valor®Radiant Gas Fireplace.
Refer to these simple remote
control instructions and
keep them handy to enjoy
your replace to the fullest.
For our video guide, visit
valorreplaces.com/remote
Sincerely,
The Valor Family,
Valor Fireplaces
BRREM19E

GETTING STARTED
Choose Fahrenheit 12-hour or
Celsius 24-hour clock.
Press OFF and low ame button to change display.
Set time.
1. Press high and low ame buttons
until time 6:00 ashes.
2. To set hour— press high ame button.
3. To set minutes— press low ame button.
Turn on your replace.
Press OFF and high ame button until you hear beeping.
Takes up to 20 seconds.

GETTING STARTED
Remote Control
Adjust ames.
To turn up, press high ame button.
To turn down, press low ame button.
Pilot only.
Press low ame button until
the replace ames shut o.
Turn your pilot o.
Press OFF.

WALL SWITCH
Wall Switch
Turn on your replace.
Press ON-OFF button
until you hear beeps.
Turn re and pilot o.
Press ON-OFF button
until replace and
pilot ame shut o.
You can’t control the thermostat
or timer with the wall switch.
Use remote instead.

SAFETY SAVINGS
5–Day Pilot Shutdown
If there is no activity after ve days, the Valor SmartPilot
System automatically shuts o the pilot.
Benet
The 5 day pilot shutdown is ideal if you happen to be away from
home for an extended period of time or don’t need the heat
during warmer Spring and Summer months—you could save
up to 5 months of unnecessary pilot consumption per year.
6–Hour Turndown
If your replace ame height hasn’t changed and you haven’t
used your remote for 6 hours, your ValorStat Remote Control
System automatically turns your replace down to pilot.
Benet
Save money in the long run. Use the temperature and timer
modes to maximize your heating experience even more.

SAFETY AND SAVINGSFAN AND LIGHTING
Circulating fan*
Adjust fan.
Click SET button until fan ashes.
•To increase fan speed— press high ame button.
•To reduce fan speed— press low ame button.
Turn fan o.
Press low ame button until all four speed level bars disappear.
Overhead lighting*
Adjust light with dimmer.
Click SET button until light bulb ashes.
•To turn on or increase light— press high ame button.
•To lower light— press low ame button.
Turn lighting o.
Press OFF. * Remote control with Valor Max remote only.
Options available on select models.

SET TEMPERATURE
Set the Temperature
You can set a warmer and a cooler temperature
twice in one day.
1. Click SET button until TEMP appears.
2. Press SET button until temperature ashes.
3. To increase temperature, press high ame button.
To decrease temperature, press low ame button.
4. Click SET button so TEMP appears.
5. Press SET button until temperature ashes.
Then, select temperature.
6. Press to save temperature settings, or let remote
automatically save the setting after a few seconds.

SAFETY AND SAVINGSSET TEMPERATURE
To use temperature setting,
make sure TEMP mode is selected.
Click SET button to select
or temperature.

SAFETY AND SAVINGSSET TIMER
Set the Timer
You can program two heat cycles for dierent times
in the day. Both cycles, P1 and P2, have a start
and an end time. Cycles cannot overlap.
Before you set the timer, set the temperature.
1. Click SET button until TIMER appears.
2. Press SET button until time 6:00 ashes.
P1 start time appears.
3. To set the hour, press high ame button.
To set the minutes, press low ame button.
4. Click SET button so P1 end time appears.
Then, select time.

SAFETY AND SAVINGSSET TIMER
5. Click SET button so P2 start time
appears. Then, select time.
6. Click SET button so P2 end time
appears. Then, select time.
7. Press to save temperature
settings, or wait a few seconds.
Only want one heat cycle?
Set the same time for these three:
P1 , P2 and P2 .

CHANGE BATTERIES
Batteries in remote
Your remote display indicates
when the battery is low.
The remote uses a 9V
alkaline battery—Duracell or
Energizer. The battery should
last one to two seasons,
depending on usage. Remove
the battery in the o-season
to extend battery life.
Still not working? Did you
know every remote has a
receiver that uses batteries?
See basic instructions
on next two pages.

CHANGE BATTERIES
Batteries for your receiver
Before you change the batteries, turn the replace and
pilot o and let it cool.
When three seconds of rapid re beeps sound, it’s time to
replace your receiver batteries.
Locate the battery holder
under the rebox near the
controls.
Replace the batteries with
4 AA alkaline (Duracell or
Energizer) batteries.
Return holder to
original location.
Reinstall any remaining
parts removed.
Have a remote battery and wall
switch instead? See next page.

Magnetic
battery access plate
Battery holder
Snap connector
Remote battery and wall switch
CHANGE BATTERIES

Batteries in remote battery and wall switch
If you have a remote battery and wall switch, your receiver
batteries are conveniently located next to the wall switch.
Pull o the FIREPLACE BATTERY ACCESS plate next to the wall
switch. The plate is attached with magnets.
Do not pull the connector by the wire!
Replace the batteries with 4 AA alkaline batteries (Duracell or
Energizer) orienting them as indicated inside the holder.
Put the battery holder and cover back in place.
CHANGE BATTERIES
If you don’t have a remote battery and
wall switch installed, see previous page.

TIPS
Tips
•Double-click the low ame
button to go directly to LO
(lowest) ame setting.
•Double-click the high
ame button to go directly
to HI (highest) ame setting.
•Only use alkaline batteries,
such as Duracell or
Energizer, with your remote
or receiver.
•When using the remote, the
handset should be within
15 feet (4½ metres) of the
replace.
•Don’t leave the handset on
the mantel or hearth.
•To keep out of children’s
reach, use the wall holder.
•Be patient when
programming: it can take a
few seconds to set.
•Once you turn a pilot o, it
takes a few minutes before
your can turn it back on.
•During extreme cold
weather, leave your replace
running to avoid problems
starting up.

TROUBLESHOOTING
Remote control doesn’t work.
1. Change the batteries in your remote control. The battery
usage icon on your remote control screen will tell you if the
batteries are low or dead.
2. Switch to Duracell or Energizer alkaline batteries. They work
best with our remote control systems.
3. Replace the remote’s receiver batteries located in your
replace or in your remote battery and wall switch. Both
your remote and your remote’s receiver require batteries.
Tip: Keep batteries fresh. Switch out your
receiver’s batteries once a year with 4new AA
Duracell or Energizer alkaline batteries.

NOTES

STAY SAFE
Please take care and stay safe
Remember to be careful when using your replace.
If you can’t nd the answer in this pamphlet, nd your
owner’s manual at valorreplaces.com/manuals.
For basic how-to videos on your remote,
go to valorreplaces.com/remotes
If you would like more information, contact your local
dealer for help or visit valorreplaces.com

SAFETY AND SAVINGS