ValueStore US WS-360 User manual

WWW.VALUESTORE.US | [e-mail]
Version: 1.5 - 2014
Wireless Alarm System
WS-360.
With mini cellular module
USER GUIDE

2
Alarm System Overview
Main Features:
 Link up to 124 wireless sensors to the alarm system.
 The system can alert to up to 5 mobile numbers by SMS or by Phone Call when the alarm
system is triggered.
 Arm and Disarm the system remotely via the text message (SMS), the system will reply to
you by an SMS confirmation.
 Diverse ways to Arm\Disarm the system: from Main Panel, by SMS, Wireless Keypad or
Remote Control.
 Zone number is displayed in the keypad’s LCD screen when an alarm or trouble condition
occurs on a sensor.
 Supports GSM, 2G, 3G and 4G SIM cards.
Technical Specifications:
 Working power: AC 100-230V, DC 12V 1A.
 Backup battery: Built-in Lithium 3.7V 800mAH (rechargeable).
 Cellular module: 4-Band (GSM, 2G, 3G and 4G). GSM transmit power: 2W.
 Receiving and emitting frequency: 868 MHz.
 Working condition: Temperature: -10ºC ~ 50ºC, Humidity: ＜80%.
 Main Paneldimension: 6.61×4.4×1.02(inch).

3
Alarm System Overview
Front side:
Back side:

4
Basic Steps to Setup Your Alarm System
STEP 1: Set date and time.
1. How to setup Time and Date. Page 5
STEP 2: Link sensors to the system and how to install them.
1. Remote Control. Page 7
2. Panic Button. Page 8
3. Gas Detector. Page 9
4. Smoke Detector. Page 10
5. Entry Sensor. Page 11
6. Motion Detector. Page 12
7. Outdoor Siren. Page 13
8. Indoor Siren. Page 14
STEP 3: Setup phone numbers for alarm notification and SIM card installation.
1. How to setup phone numbers. Page 16
STEP 4: Learn how to arm and disarm the alarm system.
1. How to arm or disarm the system from:
a. Main Panel. Page 18
b. Remote Control. Page 19
c. Mobile Phone (by SMS). Page 19
STEP 5: Learn additional features of the alarm system.
1. Siren On/ Off (Silence Alarm Mode). Page 21
2. Arm/ Disarm Beep. Page 22
3. Upload Status. Page 23
4. How to change the Code/ Password. Page 23
5. User ID. Page 24
6. Alarm History. Page 24
7. Status History. Page 24
8. Zone Attribute Page 25-26
9. Entry Delay/ Exit Delay Page 27
10. Set Smart Zone Page 28
Sensor List Installation and Notes Page 29-30

5
STEP 1:
How to setup time?
Please follow the next steps:
1. Press: “ENT”.
2. Enter Code: “888888” (this is the default password).
3. Select: “Set Time” use the arrows  to find the option in the menu.
4. Press: “ENT”.
5. Delete the old record by pressing the arrow .
6. Enter Time: HH/MM/SS. Example: it is 13 hours, 25 minutes and 15 seconds please enter:
132515
7. Press: “ENT”.
8. Done!
How to setup date?
Please follow the next steps:
1. Press: “ENT”.
2. Enter Code: “888888” (this is the default password).
3. Select: “Set Date” use the arrows  to find the option in the menu.
4. Press: “ENT”.
5. Delete the old record by pressing the arrow .
6. Enter Date: YY/MM/DD/W. Example: today is 2014 year, 11 month and 22 day and 6
Saturday (Sunday is “0”, Monday is “1” and so on) . please enter: 1411226
NOTE: Monday = 1
Tuesday = 2
Wednesday = 3
Thursday = 4
Friday = 5
Saturday = 6
Sunday = 0
7. Press: “ENT”.
8. Done!

6
STEP 2:
Important Notice:
If you have bought a pre-programmed kit you will not need to link any sensor to the
system because they have been already linked; in this case please proceed to set each
sensor in the areas you want to protect.
The Alarm System has a Neutral Zone and 3 Zone Types:
1. Neutral Zone: In this zone are linked all remote controls and keypads.
2. Emergency Zone: In this zone are linked all sensors that will be able to trigger the
alarm system whether is Arm or Disarm. What sensors are in the Emergency Zone?
-Panic Buttons.
-Smoke Detectors.
-Gas Detectors.
3. Perimeter Zone: In this zone are linked all sensors that will be able to trigger the
alarm system only when the system is Armed Home. What sensors are in the
Perimeter Zone?
-Entry Sensors (Door/Window Contact).
4. Motion Zone: In this zone are linked all sensors that will be able to trigger the alarm
system only when the system is Armed Away. What sensors are in the Motion Zone?
-Motion Detectors (P.I.R).


Now that you understand the Zone Types, please link the sensors to the
Alarm System in the corresponding Zone Number.
In the next pages you will find a step by step of how to link each sensor;
once all sensors are linked, proceed to set them in the areas you want to
protect.

7
How to link the sensors to the alarm system?
1. Remote Control:
How to install:
The remote control is ready to use, you need to do nothing.
Just use it the same way to lock or unlock your car or like a portable panic button.
You can link maximum 4 Remote Controls to the system. The zone number for the Remote Controls
is “00”.
Please follow the next steps to link the sensor to the system:
1. Press: “ENT”.
2. Enter Code: “888888” (this is the default password).
3. Select: “Program Sensor” use the arrows  to find the option in the menu.
4. Press: “ENT”.
5. Delete the old record by pressing the arrow .
6. Enter “Zone Number”: 00
7. Press: “ENT”.
8. Enter “Group Number.”: Delete the old record by pressing the arrow .
9. Enter “0” for the first remote control, “1” for the second remote control, “2” for the third
remote control and “3” for the fourth remote control.
10. Press “ENT”.
11. Choose “ActivateSensor” and press: “ENT”.
12. When appears: “Learning”, Trigger the remote control two times by pressing any other
buttons from the remote control.
13. It will appear on the screen: “Success” in case of “Failure” please repeat the process one
more time.
14. Done!

8
2. Panic Button:
How to install:
Activate the panic button from the back side of it and proceed to set it with the
strips or fix it with screws anywhere you want to have a panic button (we
recommend to install it in the master bedroom or office desk).
You can link maximum 4 Panic Buttons to the system. The zone number for the Panic Button is “02”.
Each zone supports up to 4 sensors; in case you want to link more than 4 Panic Buttons you can use
the zone number: “05”, “06”, 07”, “08” and “09”.
Please follow the next steps to link the sensor to the system:
1. Press: “ENT”.
2. Enter Code: “888888” (this is the default password).
3. Select: “Program Sensor” use the arrows  to find the option in the menu.
4. Press: “ENT”.
5. Delete the old record by pressing the arrow .
6. Enter “Zone Number”: 02
7. Press: “ENT”.
8. Enter “Group Number.”: Delete the old record by pressing the arrow .
9. Enter “0” for the first panic button, “1” for the second panic button, “2” for the third panic
button and “3” for the fourth panic button.
10. Press “ENT”.
11. Choose “ActivateSensor” and press: “ENT”.
12. When appears: “Learning”, Trigger the panic button two times by pressing the red button.
13. It will appear on the screen: “Success” in case of “Failure” please repeat the process one
more time.
14. Done!

9
3. Gas Detector:
How to install:
We recommend to set the gas detector in your kitchen or corridors, this sensor will
send an alarm notification in case of a gas leakage so you and your family can
evacuate the area before deadly gases get in to any bedroom.
You can link maximum 4 Gas Detectors to the system. The zone number for the Gas Detector is “03”.
Each zone supports up to 4 sensors; in case you want to link more than 4 Gas Detectors you can use
the zone number: “05”, “06”, 07”, “08” and “09”.
Note: You will need a lighter (the one used to light a cigarette) in order to trigger the Gas Detector
during the programming procedure.
Please follow the next steps to link the sensor to the system:
1. Press: “ENT”.
2. Enter Code: “888888” (this is the default password).
3. Select: “Program Sensor” use the arrows  to find the option in the menu.
4. Press: “ENT”.
5. Delete the old record by pressing the arrow .
6. Enter “Zone Number”: 03
7. Press: “ENT”.
8. Enter “Group Number.”: Delete the old record by pressing the arrow .
9. Enter “0” for the first Gas Detector, “1” for the second Gas Detector, “2” for the Gas
Detector and “3” for the fourth Gas Detector.
10. Press “ENT”.
11. Choose “ActivateSensor” and press: “ENT”.
12. When appears: “Learning”, Trigger the Gas Detector two times by letting escape gas from
the lighter very close to de device during two seconds twice.
13. It will appear on the screen: “Success” in case of “Failure” please repeat the process one
more time.
14. Done!

10
4. Smoke Detector:
How to install:
We recommend to set the smoke detector in the ceiling of your kitchen,
corridors or any room of your home, this sensor will send an alarm
notification in case of any detection of smoke, so you and your family can
react on time or evacuate the area before is too late.
You can link maximum 4 Smoke Detectors to the system. The zone number for the Smoke Detector is
“04”. Each zone supports up to 4 sensors; in case you want to link more than 4 Smoke Detectors you
can use the zone number: “05”, “06”, 07”, “08” and “09”.
Note: open the Smoke Detector and connect the battery before you follow the steps.
Please follow the next steps to link the sensor to the system:
1. Press: “ENT”.
2. Enter Code: “888888” (this is the default password).
3. Select: “Program Sensor” use the arrows  to find the option in the menu.
4. Press: “ENT”.
5. Delete the old record by pressing the arrow .
6. Enter “Zone Number”: 04
7. Press: “ENT”.
8. Enter “Group Number.”: Delete the old record by pressing the arrow .
9. Enter “0” for the first smoke detector, “1” for the second smoke detector, “2” for the smoke
detector and “3” for the fourth smoke detector.
10. Press “ENT”.
11. Choose “ActivateSensor” and press: “ENT”.
12. When appears: “Learning”, Trigger the smoke detector two times by pressing the small black
button(for two seconds) in the front of the smoke detector.
13. It will appear on the screen: “Success” in case of “Failure” please repeat the process one
more time.
14. Done!