Varian 900-LC Series Use and care manual

SERVICE How To
Model Number:
900 Series LC
Originator:
Des Wichems
Topic
Replacement of the PDA
detector main PWB in a 900
Series LC system
Removal & Replacement Procedures for the Main PWB for the PDA detector in a 900
Series LC
Removing the old PWB
1. Switch off detector and unplug mains cable.
2. Remove the detector’s top main cover which is held by two screws on each side.
3. Remove the two screws (1) securing the small side panel and lower it down as shown
in Figure 1.
igure 1: Removing the cooling vent
4. Locate and remove the two screws at the rear of the detector (2) used to secure the
fan baffle. hen, swing the baffle to the right as shown (Figure 2).
Number: SHT-900LC-09
Date: February 10, 2009
Pages: 5
1

igure 2: Removing the an Baffle
5. Locate and remove the two screws (3) on the rear panel.
igure 3: Removing the Screws from the Back of the Detector
6. Remove the optics module as described in the Optics section of the Service manual.
7. Remove the earth lug screw (4) located on the Processor PWB (Figure 4).
igure 4: Earth Lug Screw on Main PWB
8. Remove the single screw holding down the power supply module (5). his is located
on the outer edge of the detector adjacent to the power supply module (Figure 5).
2
3
4

Figure 5: Power Module on the detector
9. Disengage the safety cover (6) and slide the power supply module toward the front of
the detector (Figure 5). At this stage the mains supply input cables are still
connected. Place the power supply module in the service position as shown in Figure
6 below, and fasten in this position using the screw (7) which originally held it in
place.
Figure 6: Securing the Power Supply
10. he Processor PWB will now be exposed. Disconnect all cables from the Processor
PWB. he PWB can now be removed along with its mounting bracket.
5
6
7

Replacement the new PWB
11. When a new replacement Processor PWB is received, it will be accompanied by a
new MAC address label Figure 7.
Figure : MAC Address Label Sticker
12. This label needs to be stuck over the existing one (located on the rear panel o the detector as
shown below. The detector serial number will remain the same.
Figure 8: Sticker Location on the back of the Instrument.
13. he Processor PWB replacement procedure is the opposite of the removal
procedure.
NOTE
Whenever this PWB is replaced, you must perform a Gain Calibration
& 0% calibration. Refer to the Diagnostics section for details.
Setting up the ain PWB in a PDA detector to communicate with the 900 Series IB
14. Connect the Detector to your PC using a cross-over cable. Refer to SHT-PS325-02
(Connecting the PC with a 325 dynamic IP crossover cable) for additional information
on how to connect the PC to the detector using a cross-over cable. he procedure to
connect the PDA detector is very similar and these instructions can be used to
provide a concept as to how it is done.
8

15. Once the detector is communicating to the PC you need to select the Diagnostics Tab
and the Comms Tab (9) from the Diagnostics menu in PolyVerify (Figure 9).
igure 9: Selecting the Comms Tab in PolyVerify
16. Under the Fixed IP settings (10), type in the following settings (Figure 10);
fixed IP : 10.10.10.2
subnet: 255.255.255.0
gateway: 10.10.10.1
17. Click on the Set button (11), and once the Fixed Ip settings have been set, you can
read them back to the PC by selecting the Load (12) button
Figure 10 Inserting the IP Settings
18. Once the IP has been set to the address shown above, you can put the detector back into the
900 Series LC and it should communicate through the internal MIB.
9
10
11 12
Settings are the same or
the UV detector.