Vatech PAX Duo3D User manual

Installation manual 1
Contents
Chapter 1. Introduction ......................................................... 6
1.1. Product Overview.....................................................................................................................6
1.2. Product Features......................................................................................................................6
1.3. Product Components ...............................................................................................................7
1.4. Marks & Graphic Symbols .......................................................................................................8
Chapter 2. Components and Functions............................... 10
2.1. Hardware Components and Functions ..................................................................................10
2.2. Dimension of PaX-Duo3D......................................................................................................11
Chapter 3. Preparing for Installation .................................. 14
3.1. Checking Packages ...............................................................................................................14
3.2. Checking Carton No. 1...........................................................................................................15
3.3. Checking Carton No. 2...........................................................................................................16
3.4. Checking the packing list of the accessory box ..................................................................... 17
3.5. Replacement parts and positioning accessories ...................................................................19
3.6. Tools require ..........................................................................................................................20
3.7. Unpacking Carton ..................................................................................................................21
Chapter 4. Installing the unit .............................................. 24
4.1. Assembling the column and the base plate ...........................................................................25
4.2. Balancing the system after finishing unit assembly ............................................................... 33
4.3. Assembling covers.................................................................................................................34
4.4. Connecting Cables.................................................................................................................35
Chapter 5. Configuring computer........................................ 38
5.1. PC system requirements........................................................................................................38
5.2. Installing LAN card.................................................................................................................39
5.3. Connecting the LAN cable .....................................................................................................39
5.4. Connect the Frame grabber cable and the USB cable.......................................................... 40

2 PaX-Duo3D
5.5. Installing 2 USB-type License Keys. ...................................................................................... 41
Chapter 6. Installing software ............................................ 43
6.1. Installing Imaging Software and Frame grabber Driver .........................................................44
6.2. HASP Device Driver...............................................................................................................54
6.3. DirectX Driver.........................................................................................................................56
6.4. Serial Card Driver Setting ......................................................................................................58
Chapter 7. Using the HyperTerminal .................................. 62
Chapter 8. Technical specification ..................................... 66
8.1. PaX-Duo3D Specifications.....................................................................................................66
8.2. Panorama X-ray detector.......................................................................................................66
8.3. Image Magnification...............................................................................................................67
8.4. Anatomic Programs ...............................................................................................................67
8.5. User Interface.........................................................................................................................67
8.6. X-ray Generator .....................................................................................................................67
8.7. Collimator ...............................................................................................................................67
8.8. X-ray Tube .............................................................................................................................68

Installation manual 3
Attention
For improvement of product performance, supplementation, or follow-up of information; the contents of
this manual are subject to change without separate prior notice.
Please note that our company has neither responsibility for any accidents nor obligation to do free
repair service for any damage of the equipment due to user's mistake, which resulted from failure to
follow the contents in this manual. Make sure to be familiar with the safety precautions and usage
procedures. Also note that the product may slightly differ from the contents of this manual depending on
specification.
The following marks are used in this manual for the effective use of the product.
Caution for System Installation
1. To maintain safety, the installer must read and follow this manual carefully.
2. The installer must confirm that the system is installed according to this manual and perform the
appropriate procedures therein.
3. Only a VATECH & E-WOO technician or a qualified technical expert can install the system.
4. Applying pressure or spraying liquid on the system can cause fire and electrical accidents.
5. Do NOT install the system in an environment exposed to volatile gas or vapor.
6. For a stable power supply avoid using the system simultaneously with any other system of high
electrical capacity, and make sure to establish a ground for the system.
7. If there is any doubt about operation or condition, do NOT install the system until a VATECH & E-WOO
customer support team checks and confirms its reliability.
Indicates useful information and tips to use the system and about the
system.
Indicates important instructions. If not observed, malfunction or damage to
the system or other property may occur.
Indicates warnings and instructions for SAFETY. If not adhered, serious
risks and injury may be caused to the patient and user.

4 PaX-Duo3D
Guidelines for Protection against Radiation
The X-ray system may cause injury to the patient if used improperly. The instructions contained in this
manual must be read and followed when operating PaX-Duo3D. The world standard regulations
pertaining to radiation safety must be observed.
When exposing X-ray, User must be behind a protective wall, or take other protective actions. User
should keep at least 2m (7feet) away from the X-ray system when pressing the exposure switch while
observing the patient and capture-progress.
User must provide protective clothing to the patient. Before capturing, a pregnant woman must always
consult with the doctor.
X-ray Room for System Installation
Recommended Minimum Space
●PaX-Duo3D (L)1490*(W)1057*(H)2346 mm
- Above space is established considering the movements of both system operator and patient.
- The system is normally installed beside a wall, and operator uses the system on the left.
Width of Door
- The door of the X-ray room should have a clearance of more than 800mm wide to provide enough
space for transporting the system inside.
Floor area
- The floor of the X-ray room should be stable for system balance.
- The floor should also be able to support a minimum weight of 500KG.
Power Supply
- For system stability, please guarantee 3KW power supply.
Protection against radiation
- For protection against radiation, follow the government or local standards.
Safety Zone
- Check the safety zone.
Do not use this system in a place where there is danger for explosion.

Installation manual 5
Introduction
1
This chapter describes the overall features and technical specifications of
the system.

6 PaX-Duo3D
Chapter 1. Introduction
1.1. Product Overview
PaX-Duo3D is the diagnostic system which consists of Advanced Digital Dental Tomographic and
Panoramic X-ray units. Its economical CT is completely distinguished from among the other existing
technology of Tomography.
More so, its advanced digital imaging process allows for a considerably efficient diagnosis, a variety of
management information, and real-time sharing of image information in a network. It is equipped with
state-of-the-art area sensor to capture 3D Digital Tomogram Scanned Image.
zMovement Technology: Multi-motor with digital trajectory control / motorized carriage movement
zPatient Positioning: Panoramic - Triple [Mid-Sagittal, Frankfurt, Canine] laser beams positioning
CT - Triple [Mid-Sagittal, Frankfurt, Canine] laser beams positioning
Patient Positioning Aid: Chin rest, Chin support, bite fork, mirror, LCD for
instruction
zOcclusion corrector, Edentulous positioned
1.2. Product Features
Its features include:
zMaking the unit more economical, thanks to 2-into-1 combination of Panoramic and CT imaging.
zAutomatically switching the sensors from panoramic mode to CT imaging mode or vice versa.
zIncorporating the multi FOV to reduce the X-Ray dose to the patients.
zDrastically reducing X-Ray expose dose, compared with medical CT in consideration of patient's
safety.
zHelps the patients understand the diagnosis result by viewing the invisible part with a 3-D viewer
program, Ez3D2009.
zThe disk space required for installation is no more than a general panoramic system is.
zA clear Tomography image up to minimum 0.1mm at any directions.
zYou can set and control the Examination Program Mode on the console PC.
zSupport more accurate diagnosis imaging on LCD as well as voice announcement function for
patients and staffs.
zSupports the DICOM Format.

Installation manual 7
The PaX-Duo has been designed to carry out the following radiological examinations.
zPanorama Normal
zPanorama Special
zCT
zDental CT TMJ
Imaging mode Sub mode
Panorama
Normal Standard
Fast
TMJ Open
Close
CT
Mandible
Maxillary
Occlusion
CT TMJ Right
left
1.3. Product Components
<Hardware Components>
zEquipment main system
zUser's manual
zInstallation CD
zAccessories including Lock-Keys (Reconstruction Key and 3D Viewer Key)
<Software Components>
zImage Viewer program : EasyDent4 V4 program, Ez3D2009(3D Viewer program)
zImaging program : EasyDent V4
For improvement of product performance, the Components and
specification of this product may be subjected to changes without any
previous notice.

8 PaX-Duo3D
1.4. Marks & Graphic Symbols
TYPE B Equipment
Radiation hazard
This CE symbol grants the product compliance to the European Directive
for Medical Devices 93/42 as a class IIB device, as Authorized by Grand-
Duche De Luxemburg.

Installation manual 9
Components
and functions
2
This chapter describes the overall features and functions of the system.

10 PaX-Duo3D
Chapter 2. Components and Functions
2.1. Hardware Components and Functions
zLED Lamp: Indicating the current X-Ray emission activity of unit. While it stays green when the
unit is idle, led lamp turns orange when the unit is in operation.
zEmergency switch: stop the movement of the unit when it abnormally operates.
zSensor Module: Digital X-ray image sensor module for Panoramic and Dental CT imaging units.
With its Auto-Switching sensor technology, there is no need to change sensors when imaging
mode changed.
zChinrest: provide the patient comfort and rest while imaging, thus producing better image.
zLCD panel: the supporting device to monitor and control the Unit activity.
zHandle frame: is used for the patient to hold firmly while imaging to stabilize his or her position.
zColumn: is used to adjust the unit height according to the height of patient.
Column
Handle Frame
LCD Panel
Chinrest
Sensor Module
Emergency Switch
LED Lamp

Installation manual 11
This configuration may differ depending on the specification of your product.
2.2. Dimension of PaX-Duo3D

12 PaX-Duo3D

Installation manual 13
Preparing for
installation
3
This chapter describes the pre-installation for the system.

14 PaX-Duo3D
Chapter 3. Preparing for Installation
3.1. Checking Packages
3.1.1. Checking “ShockWatch” and “TiltWatch”
Check whether “ShockWatch” and “TiltWatch “on each carton has been damaged.
If it is the case, please contact your shipping company, agent or E-WOO.
The installers and/or supervisor should check the following before system
installation.
The “ShockWatch” and “TiltWatch” become red in case for cartons of being
damaged.
ShockWatch
TiltWatch

Installation manual 15
[Components in Packages]
No. Part Name Specification Q'TY
1
Vertical Column
Assembly,
Rotating Unit Assembly
With Vertical Handler 1
Vertical Front Case+LED Case 1
Vertical Top Case 1
Vertical Left Case 1
Vertical Right Case 1
Column Back Case Cover 1
Base Foot Board 1
3.2. Checking Carton No. 1
[Components in carton No. 1]
If the serial numbers don’t match, please don’t install the system.
Please make sure each carton isn’t damaged.
No. Picasso Duo
Description Q’TY
1 Column and Rotating unit assembly 1
2 Rotator upper cover 1

16 PaX-Duo3D
3.3. Checking Carton No. 2
[Components in carton No. 2]
No.
Picasso Duo
Description Q’TY
1 Base 1
2 Accessory box 1
For the Panoramic unit, column, Base, and Accessory boxes are packed
separately.

Installation manual 17
3.4. Checking the packing list of the accessory box
1 Cable Tie 70mm 10
2 Hub Cable 1
3 LAN Cable 8PIN LAN for PANO 5M 1
4 Head Rest 1
5 Rubber Cap
6 Disposable Bag Small size 1
7 Cover Column Bottom Cover 1
8 Column Back Case Cover Column Top Cover 1
9 Switch Up/Down 1
10 Handle table
11 RS232 cable 1
12 Switch X-ray Exposure Switch 1
13 Normal Bite 1
14 Wrench Bolt 8*15 4
15 Flat Headed Bolt 4*20 2
16 Holder X-ray Exposure Switch Holder 1
17 Holder X-ray Exposure Switch Holder 1
1
2
3
4
5
6
7
8
10
11
9
12
1
3
14
15
1
6
17 1
8
19
20
21
22
2
3
24
25
2
6
27 2
8
29
30
31
32
33
34

18 PaX-Duo3D
18
Block
Column Support Block A 1
19 Column Support Block A 1
20 Column Support Block B 1
21 Wrench Bolt 12*40 2
22 Screw T/T 4*12 3
23 Toothless support 1
24 Sinus support 1
25 Wrench Bolt 8*25 8
26 Flat Headed Bolt 4*10 6
27 Truss Bolt 4*10 4
28 Wrench Bolt 8*40 4
29 Truss Bolt 4*6 15
30 Flat Headed Bolt 3*8 3
31 Chin Support With Pin(2EA) 1
32 Normal support 1
33 TMJ support 1
34 Block Base Support Block 1
Disposables Nonwoven for Headrest 1
Nonwoven for Chinrest 1
Spring Washer ø8 6
Flat Washer ø8 6
Computer
Computer 1
Mouse 1
Key Board 1
Vaccine CT Software Kit with activation code 1
Monitor Monitor 17" 1