Velleman PI600M User manual

DC TO AC POWER INVERTER
POWER : 600W
PI600M for input voltage 12V
PI60024 for input voltage 24V
User Manual
Gebruikershandleiding
Manuel d'utilisation
Bedienungsanleitung
ATTENTION – OPGELET - ACHTUNG
OVERLOADING THIS DEVICE OR CONNECTING IT WITH AN INDUCTIVE LOAD (e.g. refrigerator, fan,
drill) WILL DAMAGE IT AND AUTOMATICALLY VOID THE WARRANTY !!
HET TOESTEL ZAL WORDEN BESCHADIGD INDIEN U HET OVERBELAST OF ER EEN INDUCTIEVE
BELASTING (vb. koelkast, boormachine, ventilator) OP AANSLUIT. DE GARANTIE VERVALT DAN
AUTOMATISCH !!
LA SURCHARGE DE L’APPAREIL OU LA CONNEXION D’UNE CHARGE INDUCTIVE (p.ex. ventilateur,
réfrigérateur, perceuse) ENDOMMAGERONT L’APPAREIL ET LA GARANTIE SERA INVALIDEE
AUTOMATIQUEMENT !!
DIE GARANTIE ERLISCHT UND DER SPANNUNGSWANDLER KANN BESCHÄDIGT WERDEN, WENN SIE
IHN ÜBERLASTEN ODER MIT EINER INDUKTIVEN LAST VERBINDEN (z.B. Kühlschrank, Lüfter,
Bohrmaschine).

PI600M & PI60024 v2 GB1
voltage
indicator
power
switch
AC output
socket
crocodile
clips
1. DESCRIPTION
2. CONNECTIONS
Connect the red cable from the "+" terminal (red terminal) of the battery to the +
binding post (red connection) of the inverter and the black cable from the "-"
terminal (black terminal) of the battery to the "-" binding post (black connection) of
the inverter. The length of the cable is ≤2m.
Be sure to tighten the screws in order to avoid loose connection.
3. OPERATION
When connected to an appliance, remember to turn on the inverter before turning
on the appliance. If the buzzer sounds during operation, this indicates that the
battery voltage is very low and that the inverter will be disconnected in 5 minutes.
then the
device Switch on inverter

PI600M & PI60024 v2 GB2
4. OUTPUT CAPACITY
The inverter will switch off automatically if the total wattage of the electrical
appliances exceeds the inverter's output capacity. This will also happen if the
temperature of the inverter exceeds 55°C due to prolonged use.
5. SPECIAL RECOMMENDATIONS
Unplug the AC inverter when not in use and when starting the vehicle's motor.
If the AC inverter makes a beeping sound : switch off your appliance, unplug the
inverter and restart your vehicle's engine. The beeping sound is simply the low-
battery warning, which indicates that the voltage of your battery is getting low.
Your inverter will shut down automatically if you do not restart your engine and
continue the use of your inverter. This will leave your vehicle's battery at about
10.5VDC (21VDC when using a 24V inverter), enabling you to start your engine
and resume operation of the inverter. It also eliminates the possibility of being
stranded with a dead battery.
To avoid over-discharging the battery, you should let your engine run for 10 to 20
minutes after every 2-3 hours of use. This allows your vehicle's battery to recharge.
Please remember to connect the "+" wire to the "+" terminal and the "-" wire to the
"-" terminal if you choose to use an adapter in order to establish a direct
connection between the AC inverter and the battery terminals. IF YOU CONNECT
THE WIRES TO INCORRECT TERMINALS, THE POLARITY WILL BE
REVERSED AND THIS WILL DAMAGE THE INVERTER. REVERSED
POLARITY WILL INSTANTLY VOID YOUR INVERTER'S WARRANTY.
Please remember to disconnect the AC inverter before using the battery charger
to replenish you battery's voltage. Failure to disconnect the inverter prior to
connecting a charger may result in an input spike that will damage the inverter.
CONNECTING THE INVERTER'S INPUT TO A BATTERY CHARGER WILL
VOID THE WARRANTY AND MAY DAMAGE THE INVERTER
The battery's voltage must never exceed 15VDC (30 VDC for a 24V inverter).
CONNECTING THE INVERTER TO A DC POWER SOURCE GREATER THAN
15VDC (30VDC) WILL VOID THE WARRANTY AND MAY DAMAGE THE
INVERTER.

PI600M & PI60024 v2 GB3
6. ADDING EXTENSION CORDS
We recommend that the buyer refrain from using an extension cord between the
DC power source and the inverter's DC input. Connecting an extension cord to
the DC input will create a voltage drop, entailing reduced efficiency and output.
Instead, we recommend the use of an extension cord between the AC output and
the AC appliance. You may use up to 100ft (30m) of high quality extension cord.
A longer cord may result in reduced power.
7. EARTHING CONNECTION
WARNING : YOU MUST PROVIDE THE INVERTER WITH AN EARTHING
CONNECTION BEFORE USING THE INVERTER.
• The rear panel of the inverter is equipped with a terminal fitted with a wing nut.
This terminal is connected to the case of the inverter and also to the earthing
terminal of the AC output socket. The nature of your installation will determine
whether or not you need this terminal. Always use heavy-duty yellow and green
wiring for this connection.
• In a stationary land-based installation, the earthing terminal should be
connected to a metal earthing stake driven into the ground to a minimum depth
of 1.2m. One of the battery terminals (preferably the negative one) should also
be connected to the earthing stake if the battery system powering the inverter is
not equipped with a ground connection.
• If the inverter is used in a vehicle, where it is wired directly to the battery, the
earthing terminal is simply connected to the chassis. If, however, the inverter
has to power equipment used outside the vehicle, an earthing stake should be
used as described above.
• Connect the earthing terminal to the existing grounding system when the
inverter is used on a boat.
NOTE :The earthing terminal of the AC outlet is connected to the neutral
terminal. This is the same as with a standard household power point
where the neutral connection is bonded to earth and there is no voltage
between the two.

PI600M & PI60024 v2 GB4
BAD
GOOD
8. FUSE
Please check the fuse if the voltage indicator is not lit during operation. Replace
blown fuses with an identical one.
FUSE : max. 35A for a 12V inverter or 20A for a 24V inverter.
9. MEASURING AC VOLTAGES
The output wave of the AC inverter is a MODIFIED SINEWAVE. If you choose to
measure the AC output voltage, you must use an AUTHENTIC RMS VOLT
METER. Using any other type of voltage measuring device will result in an AC
voltage reading that is up to 20 to 30 volts lower than the rated value. The reading
will only be accurate when using an authentic RMS voltmeter.
10. VENTILATION
IMPORTANT ! During operation, make sure the fan keeps revolving. Check the
inverter for possible malfunctions if the fan does not work when this unit is being
used.
Make sure the fan is not blocked in order to avoid poor ventilation.

PI600M & PI60024 v2 GB5
11. CHASSIS EARTHING
The chassis earthing lug should be connected to an earthing point, which will vary
depending on where the power inverter is installed. In a vehicle, connect the
chassis ground lug to the chassis of the vehicle. In a boat, connect to the boat's
grounding systems. In a fixed location, connect to earth.
12. CAUTION
In case of trouble with the AC output, e.g. short-circuit, overload, etc… the
protection circuit will automatically cut off the output.
In such cases : (A) switch off the power at once
(B) disconnect all units
(C) check the connected devices
(D) use the units again as soon as any problems
concerning the connected devices have been solved
When in use for a prolonged period of time, the AC output may suddenly be cut
off although the battery voltage is still very strong. This may be caused by
excessive temperatures. If this happens, please proceed as follows :
(A) Switch off the inverter at once
(B) Disconnect some of the appliances or wait until the inverter cools off
(C) Switch the inverter back on
Always keep the inverter in an environment which is :
(A) Well-ventilated
(B) Not exposed to direct sunlight or any other heat source
(C) Inaccessible to children
(D) Safe from water/moisture, oil or grease
(E) Safe from any flammable substance
If the inverter is connected in the wrong way, this will void the warranty.

PI600M & PI60024 v2 GB6
13. MAINTENANCE
Very little maintenance is required to keep your inverter operating smoothly.
Clean the exterior of the device periodically using a damp cloth in order to prevent
the accumulation of dust and dirt. Tighten the screws on the DC input terminals
whenever you are cleaning the device.
14. SPECIFICATIONS
•DC input voltage : 12V / 24V, refer to model label !!!
•AC output voltage : 230V
•Output frequency : 50Hz
•Continuous output power : 600W
•Output waveform : modified sinewave
•No load current : < 1A
•Battery low alarm & shutdown : 10.5 ±0.5VDC for a 12V input
21
±1VDC for a 24V input
•Input current at 100% load : 64A for a 12V inverter, 32A for a 24V inverter
• Output current at 100% load : 2.6A
•Overheating protection : 55 ±5°C
•Dimensions : 205 x 73 x 290mm
•Weight : 2.1kg
15.NOTE
All specifications are typical at nominal input voltage, 50% load and 25°C unless
otherwise noted. All specifications are subject to change without prior notice.
WARNING : DO NOT DISASSEMBLE THIS UNIT AS DOING SO MAY CAUSE
HAZARDOUS VOLTAGES !! RETURN THIS UNIT TO THE DEALER IN CASE
OF TROUBLE !!
IMPORTANT : DO NOT CONNECT ANY INDUCTIVE LOADS WITH THIS
DEVICE !