Velleman CTC1000DS User manual

CTC1000DS
DOOR/WINDOW CONTACT FOR CTC1000
DEUR-/VENSTERCONTACT VOOR CTC1000
CONTACT DE PORTE/FENÊTRE POUR CTC1000
CONTACTO DE PUERTA/VENTANA PARA CTC1000
TÜR-/FENSTERKONTAKT FÜR CTC1000
CONTACTO DE PORTA/JANELA PARA O CTC1000
USER MANUAL 3
GEBRUIKERSHANDLEIDING 11
MODE D'EMPLOI 19
MANUAL DEL USUARIO 28
BEDIENUNGSANLEITUNG 36
MANUAL DO UTILIZADOR 45

CTC1000DS
V. 01 –12/06/2013 2 ©Velleman nv

CTC1000DS
V. 01 –12/06/2013 3 ©Velleman nv
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that
disposal of the device after its lifecycle could harm the
environment. Do not dispose of the unit (or batteries) as
unsorted municipal waste; it should be taken to a
specialized company for recycling. This device should be
returned to your distributor or to a local recycling
service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly
before bringing this device into service. If the device was damaged in
transit, don't install or use it and contact your dealer.
2. Safety Instructions
Keep the device away from children and
unauthorised users.
Indoor use only.
Keep this device away from rain, moisture,
splashing and dripping liquids.
Remove power before opening the cover.
Be very careful, touching live wires can
cause life-threatening electroshocks.
Damage caused by disregard of certain guidelines in this manual
is not covered by the warranty and the dealer will not accept
responsibility for any ensuing defects or problems.
Keep the device away from splashing and dripping liquids.
Note that damage caused by user modifications to the device is
not covered by the warranty.
This system can provide valuable protection for your home and
property if used properly. However, it cannot guarantee complete
protection against burglary or robbery. Therefore, VELLEMAN nv
will not be responsible for any losses or damages which occur
during the use of this product.

CTC1000DS
V. 01 –12/06/2013 4 ©Velleman nv
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last
pages of this manual.
Have the system installed by a qualified installer.
Respect the legislation in your region when installing an alarm
system. If necessary, refer to local authorities.
Protect this device from shocks and abuse. Avoid brute force when
operating the device.
Protected the device against extreme, dust and moisture.
Familiarise yourself with the functions of the device before actually
using it.
All modifications of the device are forbidden for safety reasons.
The device does not contain any user-serviceable parts except for
the battery.
Only use the device for its intended purpose. Using the device in
an unauthorised way will void the warranty.
4. Features
lithium battery pre-installed for easy installation
compact and unobtrusive design for easy mounting on doorframes
tamper-proof: housing cannot be opened or removed from the
mounting surface
randomized supervision signals for trouble-free system integrity
checking
low battery detection
built-in reed switch and external contact can be used
simultaneously
powerful magnet, 30 mm space between the door/window contact
and magnet
enhanced flexibility: built-in extension terminal to add wired
detectors
LED: error and test mode indicator
works with the control panel CTC1000 (not included)
5. Overview
Refer to the illustrations on page 2 of this manual.
1
mounting holes
2
LED / test button

CTC1000DS
V. 01 –12/06/2013 5 ©Velleman nv
3
fixing screw
4
battery insulator
5
tamper switch
6. Battery
The door contact comes with the battery already installed.
Low battery detection
The door contact has a low battery detection system.
The supervision function on the CTC1000 control panel checks the
battery status every 30 to 50 minutes.
The control panel must detect the low battery signal for at least
10 times with a time interval of 10 minutes.
If battery is low, the control panel will display an error message.
Replacing the battery
1. Put the control panel in configuration mode to avoid triggering
the tamper alarm (tamper alarm is not active in this mode).
2. Remove the screws and the cover.
3. Remove the old batteries.
After removing the old batteries, press the tamper switch twice
to fully discharge before inserting new batteries.
4. Insert new batteries (always use the correct battery type: see
Technical specifications below). Make sure the polarity is correct.
5. Put back the cover and fasten the screws.
Note
Low battery detection operates where the door contact has enough
reserve power to typically operate for 1 month before complete
exhaustion. When the door contact has a low battery, its LED will
flash.
WARNING
Do not puncture or throw batteries in fire as they might
explode.
Keep batteries away from children.

CTC1000DS
V. 01 –12/06/2013 6 ©Velleman nv
7. Installation
7.1 Set up connection between the contact and the control
panel
1. On first use, pull out the battery protection strip on the back.
2. On the CTC1000 control panel, go to the Add Device menu
(see chapter Managing devices in the CTC1000 manual).
3. On the door/window contact, press the test button.
4. Refer to the control panel user manual to complete the learn-in
process.
5. When the door/window contact is added, put the control panel
into Walk Test mode.
6. Hold the door/window contact in the desired location, and press
the Test button.
The LED will flash to confirm that this location is within signal
range of the control panel.
7. Proceed with mounting and installation once you are satisfied
that the door/window contact location functions properly.
7.2 Find a suitable location
It is recommended to place the contact on the door frame and the
magnet on the door.
If the contact is placed on the door:
1. Find a suitable location close to your door or window to install
the contact.
2. The contact has 2 rib-marks on one side (refer to figure),
marking the internal magnet switch location. The door/window
contact should be installed either upright or inverted, to ensure
that the rib-marked side face the magnet.
7.3 Mounting the door/window contact
1. Use the 2 contact mounting holes as a
template for appropriate hole positioning.
2. Use the provided wall plugs for
plaster/brick installation.
3. Screw the contact into the provided wall
plugs.
4. Fit the magnet on the door using the small
piece of double sided adhesive tape or with
provided screws.

CTC1000DS
V. 01 –12/06/2013 7 ©Velleman nv
The magnet must align with the marked side of the door
contact as shown in figure.
oThe magnet should not be more than 15 mm from the detector
when the door is closed.
oEnsure the tamper switch spring is positioned so that it makes
contact with the mounting surface through the tamper switch
aperture.
oWindows can be protected similar to door installations. When
fitting to a window fix the magnet to the moving window part
and the door switch to the stationary frame.
5. Put the control panel into Walk Test mode, and press the test
button on the door contact.
The LED indicator will now flash every time the door contact is
operated.
6. Fit the white caps to the two mounting holes of the door contact.
7. Installation is finished.
7.4 Mounting the door/window contact with the extension
terminal
The door contact has an extension terminal providing enhanced
installation flexibility. The extension terminal may be useful for the
following:
If the door contact cannot be
mounted on the door frame, you
can connect an additional
(extension magnet switch) to
the (Extension Terminal)
mounting the door contact
remotely.
More than one window and door
can be protected by a door
contact using the additional
magnet and extension magnet
switch. The switches must be
wired to the (Extension Terminal) as shown:
Any dry contact device with N.C. (normally closed), such as a
broken glass detector, gas detector, water sensor etc, can be
connected to the (extension terminal) making the door contact
serve as an (universal transmitter).

CTC1000DS
V. 01 –12/06/2013 8 ©Velleman nv
1. Open the door contact by loosening the fixing screw.
2. The upper end of the front case has a thinner plastic recess.
Break through the recess creating a hole for the wiring
connection to the extension terminal.
3. Connect the external device(s) to the extension terminal as
shown in the diagram.
Notes
The extension terminal forms a closed loop with the device
connected to it. when the loop is opened (the device is triggered),
the door contact is activated.
The device connected to the extension terminal is in series with
the internal magnet switch: both can work together
simultaneously.
You can choose to use the extension terminal alone with the
internal magnet switch bypassed or to use both together.
If both the internal magnet switch and extension terminal operate
together, then:
oWhen the protected door is opened/closed or the external
device is triggered, the door contact activates and transmits a
signal immediately.
oHowever, the door contact will only transmit a (door closed) or
(restored signal) after the protected door and the external
device are restored for 3 seconds.
7.5 Internal switch and terminal
Loosen the bottom fixing screw and remove the cover to reveal
terminal as shown.
Extension Terminal (1)
In addition to the built-in magnet switch, an additional 2-pin dry
contact terminal is provided for an extension magnet switch or any
device with NC (Normally Closed) functionality.
JP 2 =Internal Magnet Switch Bypass Jumper Switch
Jumper ON (jumper link inserted
connecting two pins); the internal
magnet switch will be bypassed. Only
the device connected to extension
terminal will activate the door contact.

CTC1000DS
V. 01 –12/06/2013 9 ©Velleman nv
Jumper off (jumper link removed or
(parked) on one pin), the internal
magnet switch is in use (factory default)
8. Operation
LED Indicator
In normal operation mode, the LED will not light.
When the door contact is in low battery condition, every time the
door contact is activated (device opened/ closed), the LED will
light on for 2 seconds.
When the cover is opened and the tamper switch is violated, the
LED will light on for 2 seconds. When a tamper condition persists,
every time the door contact is activated, the LED will light on for 2
seconds.
When the device contact is in test mode, the LED will flash every
time it is activated.
Test mode
Each press of the test button causes the door contact to transmit
a radio range test signal to the control panel and will enter the
test mode for 3 mins. When the test signal is transmitted, the led
will flash to confirm signal receipt by the control panel.
Each additional test button press will extend test mode another 3
mins.
9. Self test
After installation, the door contact will send self test signals to the
control panel at random intervals of 30 to 50 minutes.
If the control panel does not receive self test signals from the
contact, the panel will display an error message.
Refer to the section Supervision in chapter Special Settings of the
control panel manual.
10. Technical Specifications
power supply
1 x 3.6 V lithium 1/2 AA battery (incl.)
frequency
868.6375 MHz
operating temperature
-20 to 50 °C
humidity
up to 95 % non-condensing

CTC1000DS
V. 01 –12/06/2013 10 ©Velleman nv
dimensions
103 x 31 x 21 mm
weight
57 g
Use this device with original accessories only. Velleman nv
cannot be held responsible in the event of damage or injury
resulting from (incorrect) use of this device.
For more info concerning this product and the latest version
of this manual, please visit our website www.velleman.eu.
The information in this manual is subject to change without
prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All
worldwide rights reserved. No part of this manual may be copied,
reproduced, translated or reduced to any electronic medium or
otherwise without the prior written consent of the copyright holder.