manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Velleman
  6. •
  7. Transmitter
  8. •
  9. Velleman K8049 User manual

Velleman K8049 User manual

Total solder points: 53
Difficulty level: beginner 1 23⌧45 advanced
15 Channel IR transmitter
ILLUSTRATED ASSEMBLY MANUAL H8049IP-1
K8049
K8049
CompatiblewithmostVellemanIRreceiverkits,4
adressesallowtheuseofmultiplereceiversin
oneroom.
Specifications:
• Power supply : 3 AAA batteries
• Up to 15 channels can be operated.
• Dimensions : 150 x 58 x 22mm / 5,9 x 2,3 x 0,86”
Features:
 Works together with K6711, K6712, K6713, K8046, K8050, K4100, K4500, MK161, MK163,
MK164, …
 4 addresses allow the use of multiple receivers in one room
 Ergonomic design for extra comfort.
 LED function indication.
 Rubber keypad
2
Features & specifications
Schematic diagram.
3
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them
carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to
give it a wet look. This is called ‘thinning’and will protect the tip, and enables you to
make good connections. When solder rolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads,
hold the lead so they cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒ Make sure the skill level matches your experience, to avoid disappointments.
⇒ Follow the instructions carefully. Read and understand the entire step before you perform each
operation.
⇒ Perform the assembly in the correct order as stated in this manual
⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒ Values on the circuit diagram are subject to changes.
⇒ Values in this assembly guide are correct*
⇒ Use the check-boxes to mark your progress.
⇒ Please read the included information on safety and customer service
⇒ * Typographical inaccuracies excluded. Always look for possible last minute manual updates,
indicated as ‘NOTE’on a separate leaflet.
0.000
4
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully
solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
Assembly hints
AXIAL COMPONENTS ARE TAPED IN
THE CORRECT MOUNTING SEQUENCE !
5
9mm
9mm
 LD2 : 3mm RED
First : Bend the leads exactly like the drawing.
(Fig 1.0)
Next : Mount this LED like in the drawing (fig.
2.0). Solder one lead, check the position, if
necessary correct it by heating the soldering.
Last solder the second connection.
FIG. 2.0
Bend the LED exactly like the drawing (fig.
3.0).
FIG. 3.0
Construction
 R1 : 100K (1-0-4-B)
 R2 : 100K (1-0-4-B)
 R3 : 10 (1-0-0-B)
 R4 : 470 (4-7-1-B)
 R5 : 470 (4-7-1-B)
2. 1/8W Resistors
R...
1. Jumpers
 C3 : 100nF (104, µ 1)
3. Ceramic Capacitor
C...
 IC1 : 14p
4. IC socket. Watch the position of the
notch!
5. LEDs. Watch the polarity!
 J1
 J2
 J3
 J4
 J5
 J6
 LD1
Fit the IR LED horizontally and in line with the
PCB, (fig 4.0).
FIG. 4.0
 Pay attention to the polarity!
IR-LED
3mmLED
6. IR - LED. Watch the polarity!
FIG. 1.0
6
Construction
 T1 : BC639
 Attention : Mount the transistor on the solder side!
Now bend the transistor towards the pcb, away from the IR & 3mm LED.
7. Transistor
 IC1 : VK8049 programmed Pic16F630.
8. IC. Watch the position of the notch!
T1
 Solder a wire of 7cm (Ø 0,20mm)to the negative (-) connection of the PCB. The other end of
the wire will be soldered to the negative battery contact later on.
9. Battery contacts
Solderside
FIG. 5.0
FIG. 6.0
FIG. 7.0
 Make sure the transistor
connections do not contact
any other parts of the
circuit.
7
 Now place the battery contacts into the housing on their right places.
 Connect now the wire that you earlier have mount to the negative battery lip.
 Connect a jumper between the positive battery lip and positive connection on the pcb.
Construction
1
2
3
4
 Positive battery lip
 Common battery lip
 Common battery lip
 Negative battery lip
1
2
3
4
Negative battery lip
Positive battery lip
FIG. 8.0
8
 First bend the battery lips over before closing the enclosure.
 Close the enclosure with the supplied screws.
10. Assembly
Assembly
FIG. 9.0
9
11. Keyboard Layout
Keyboard layout
1
3
5
7
2
4
6
8
SHIFT
5
6
7
8
1
2
3
3
Mute
Power
Volume up
Preset up
Volume down
Preset down
Source
Tuner seek
Insert the batteries in the battery
compartment as indicated in fig. 10
and close the compartment.
Remark : Respect your national
and local laws when disposing of
empty batteries.
FIG. 10
10
At first power up, mode 1 is automatically selected.
 Press and hold SHIFT to change mode. Led starts flashing.
 Press button 1..8 to select desired mode as shown below.
 Hint : When the batteries are inserted, the led flashes 1..4 times indicating the selected mode.
Key Description
1 'K6710 emulation with D4 mounted'- mode. Allows control of MK161/K8050/K6711/12/13.
15 channels available ('shift' & '8' = all clear). Shift is cleared after each key press.
2 'K6710 emulation with D6 mounted'-mode. Allows control of MK161/K8050/K6712/13. 15
channels available ('shift' & '8' = all clear). Shift is cleared after each key press.
3 'K6710 emulation with D5 mounted'-mode. Allows control of MK161/K8050/K6712/13. 15
channels available ('shift' & '8' = all clear). Shift is cleared after each key press.
4 Allows simultaneous control of K4100/K4500, MK163/MK164, MK161 and
K8050/K6711/12/13
5 Identical to 1 but ‘shift’is not cleared after each key press.
6 Identical to 2 but ‘shift’is not cleared after each key press.
7 Identical to 3 but ‘shift’is not cleared after each key press.
8 Identical to 4 but ‘shift’is not cleared after each key press.
12. Mode selection
To access channel 1..8 :
 Press button for channel 1..8.
 Holding the button will result in continuous transmission, led will flash indicating transmission.
To access channel 9..16 :
 Briefly press 'shift'. Led will light indicating that 'shift' has been pressed.
 Press button 1..8 to access channel 9..16
 Holding the button will result in continuous transmission.
If no button is pressed after 'shift' has been pressed, the 'shift'-led will turn off in about 10s, hereby
cancelling the 'shift'-selection.
Pressing 'shift' repeatedly toggles between shift-on and shift-off.
13. Use
Mode selection & Use
11
14. PCB layout.
PCB
VELLEMAN KIT NV
Legen Heirweg 33
9890 Gavere
Belgium Europe
Info ?: http://www.velleman.be
Modifications and typographical errors reserved
© Velleman Kit nv
H8049IP - 2003 - ED2
5410329 291983

Other Velleman Transmitter manuals

Velleman SO11001 User manual

Velleman

Velleman SO11001 User manual

Velleman AVMOD11 Series User manual

Velleman

Velleman AVMOD11 Series User manual

Velleman K6710 User manual

Velleman

Velleman K6710 User manual

Velleman AVMOD17 User manual

Velleman

Velleman AVMOD17 User manual

Velleman K8059 User manual

Velleman

Velleman K8059 User manual

Velleman K8058 User manual

Velleman

Velleman K8058 User manual

Velleman K8074 User manual

Velleman

Velleman K8074 User manual

Velleman CARSFM3 User manual

Velleman

Velleman CARSFM3 User manual

Velleman vm118 User manual

Velleman

Velleman vm118 User manual

Velleman PMR3 User manual

Velleman

Velleman PMR3 User manual

Velleman VM121 User manual

Velleman

Velleman VM121 User manual

Velleman K8074 User manual

Velleman

Velleman K8074 User manual

Popular Transmitter manuals by other brands

GRAUPNER Kingpad mc-edition mc-28 user manual

GRAUPNER

GRAUPNER Kingpad mc-edition mc-28 user manual

Williams Sound Whisper T863 Instructions for use & care

Williams Sound

Williams Sound Whisper T863 Instructions for use & care

HK Instruments DPT-2W- 100-R2 installation instructions

HK Instruments

HK Instruments DPT-2W- 100-R2 installation instructions

ARTEX B406-4 Description, operation, installation and maintenance manual

ARTEX

ARTEX B406-4 Description, operation, installation and maintenance manual

Motorola DSP56011 user manual

Motorola

Motorola DSP56011 user manual

Selve Commeo Control Operating	 instruction

Selve

Selve Commeo Control Operating instruction

hospicall Easywave FU2-AMB manual

hospicall

hospicall Easywave FU2-AMB manual

M-system Mini-M M2RS instruction manual

M-system

M-system Mini-M M2RS instruction manual

GEIGER LC AIR GF230 Original assembly and operating instructions

GEIGER

GEIGER LC AIR GF230 Original assembly and operating instructions

Kobold NMC operating instructions

Kobold

Kobold NMC operating instructions

Crestron CNRFHT-15A Operation guide

Crestron

Crestron CNRFHT-15A Operation guide

Honeywell XNX quick start guide

Honeywell

Honeywell XNX quick start guide

Fosworks OMNI Tx-4.1 DCC quick start guide

Fosworks

Fosworks OMNI Tx-4.1 DCC quick start guide

ABB 266 DDS Operating	 instruction

ABB

ABB 266 DDS Operating instruction

Danfoss AKS 41 Technical leaflet

Danfoss

Danfoss AKS 41 Technical leaflet

FlowLine EchoPulse LR30 Series quick start guide

FlowLine

FlowLine EchoPulse LR30 Series quick start guide

Visonic MCT-212 AMBER user guide

Visonic

Visonic MCT-212 AMBER user guide

Crestron DM-TX-4K-202-C quick start

Crestron

Crestron DM-TX-4K-202-C quick start

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.