Velleman K8059 User manual

2 CHANNEL RF CODELOCK TRANSMITTER
K8059
ILLUSTRATED ASSEMBLY MANUAL H8059IP-1
Total solder points: 63
Difficulty level: beginner 12345 advanced
ForusewithK8057/VM109
2ChannelRFreceiver

3
Features:
 For use with the K8057/VM109 2-channel RF receivers.
 Generates unique 32-bit code.
 More than 1,000,000,000 unique codes.
 Code can easily be changed for safety purposes.
 Choose continuous or 'burst' transmission.
 LED indicator.
 Limited compatibility with K6706 - K6706A - K6706B/G
Specifications:
 Power supply: 12V battery V23GA, GP23GA,... (not incl.)
 433MHz operation
 Open field range of up to 30m possible
 Dimensions: 63 x 40 x 16mm (2.5" x 1.6" x 0.6")
Features & Specifications
Velleman hereby certifies that the device K8059 meets the essential requirements and all other relevant
stipulations of directive 1999/5/EG and 1995/5/EC.
For the complete conformity declaration check out :
Http://www.velleman.be/downloads/doC/CE_K8059.pdf

4
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it oftenon a wet sponge or cloth, to keep it clean; then apply solderto the tip, togive it a wetlook. This is called ‘thinning’ and will
protect the tip,and enables you to makegood connections. When solder rolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒Make sure the skill level matches your experience, to avoid disappointments.
⇒Follow the instructions carefully. Read and understand the entire step before you perform each operation.
⇒Perform the assembly in the correct order as stated in this manual
⇒Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒Values on the circuit diagram are subject to changes.
⇒Values in this assembly guide are correct*
⇒Use the check-boxes to mark your progress.
⇒Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates,indicated as ‘NOTE’ on a separateleaflet.
0.000

5
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE
CORRECT MOUNTING SEQUENCE !
You will find the colour code for the resistances and the LEDs on our website:
http://www.velleman.be/common/service.aspx

6
Construction
 SW1 : KRS0611
 SW2 : KRS0611
 SW3 : KRS0611
5. Push buttons
 X1 : SAW433
4. SAW resonator
X...
 D1 : BAT85
 D2 : BAT85
1. Diodes. Watch the polarity!
D...
CATHODE
 ZD1 : 5V1 / 500mW
2. Zenerdiode. Watch the
polarity!
ZD...
CATHODE
 R1 : 33K (3 - 3 - 3 - B)
 R2 : 33K (3 - 3 - 3 - B)
 R3 : 33K (3 - 3 - 3 - B)
 R4 : 47 (4 - 7 - 0 - B)
 R5 : 220 (2 - 2 - 1 - B)
 R6 : 2K7 (2 - 7 - 2 - B)
3. 1/8W Resistors
R...
 IC1 : 8p
6. IC socket. Pay attention
to the position of the notch!
PIN1

7
Construction
 T1 : MPSH10
10. Transistor
 +
 -
 Check for good attachment of
the solder to the contacts
7. Battery contacts
 C1 : 1pF (1)
 C2 : 4p7 (4.7)
 C3 : 100pF (101)
 Bend C3 away from the LED
 C4 : 100pF (101)
 C5 : 100pF (101)
 C6 : 100nF (104)
9. Capacitors
 IC1 : VK8059
VK8059=(ProgrammedPIC12F629)
 Pay attention to the position
of the notch!
11. IC. Pay attention to the
notch !
Affix the supplied sticker to the
back of the housing.
12. Sticker
Velleman
SRFCE
433,92 MHz
 LD1 : 3mm blue
8. LED
COLOR= 2...5
LD.
CATHODE
8mm
LD...
-
+

8
The transmitter comes with a factory set default code. However, for security reasons, it might be wise not to
use the default code.
1. To program your unique code :
 Hold SW1(*) (left button).
 Briefly press the 'program'-button (SW3) 3 times. The LED will flash 3 times.
 Release SW1.
 Your unique 32-bit code has been generated and stored.
(*If you hold SW2 (right button) instead of SW1 (left button), the unit will generate and store your unique 32-
bit code and the transmitter will be configured in such a way that continuous transmission is not possible i.e.
if you hold either button transmission will stop after a +/- 1s)
2. To return to the default code :
 Hold SW1 (left button).
 Hold the 'program'-button (SW3).
 After +/- 10s the led will flash 5 times.
 Release both buttons.
 Your code has been erased.
 To set a new code, see point 1.
Use
13. Use

9
3.Compatibility with previous transmitters (K6706 - K6706A - K6706B - K6706G) :
3 different codes can be generated, solder a bridge as indicated below.
MODIFY EXCISTING TRANSMITTERS AND RECEIVERS :
-
+
-
+-
+
UM3758
No code UM3758
Pin1with -UM3758
Pin1with +
NEW
OLD

10
14. Schematic diagram.
Schematic diagram
C3
100p
C1
1p
C2
4p7
T1
MPSH10
R5
220-1/8W
R4
47-1/8W
LD1
LED3RL
X1
SAW433
R1
33K-1/8W
C4
100p
SW1
SW KRS0611
SW2
SW KRS0611
GP4/T1G/OSC2/CLKOUT
3
Vdd
1
GP5/T1CKI/OSC1/CLKIN
2
GP3/MCLR/Vpp
4
GP2/T0CKl/INT/COUT
5
GP0/CIN+/ICSPDAT
7
GP1/CIN-/ICSPCLK
6
Vss
8
IC1
PIC12F629
J2J1
SW3
SW KRS0611
R3
33K-1/8W
R6
2K7-1/8W
D2
BAT85
D1
BAT85
C5
100p
C6
100n
ZD1
5V1/0.5W
BAT1
12V
R2
33K-1/8W
L

11
PCB
15. PCB

Modifications and typographical errors reserved
© Velleman Components nv.
H8059IP - 2004 - ED1 (rev. 1.0)
VELLEMAN Components NV
Legen Heirweg 33
9890 Gavere
Belgium Europe
www.velleman.be
www.velleman-kit.com
5410329 312077